Power Supply and Wiring Sample Clauses

Power Supply and Wiring. Take care when using a power supply with an overcurrent detector, because this sensor uses DC-DC converter for its power supply circuit and inrush current may activate the protective circuit for a power supply with an overcurrent detector. Recommended power supply: S8VS-06024 (Omron, DC24 V 2.5 A 60 W) • The supply voltage must be within the rated range (DC24 V ± 10 %). • Reverse connection of the power supply is not allowed. • Unstable voltage may cause unexpected operation of the sensor controller. If such condition is anticipated, use an UPS (Uninterruptible Power Supply). Recommended UPS: S8BA Series (OMRON) • Open-collector outputs should not be short-circuited. • Use the power supply within the rated load. • High-voltage lines and power lines must be wired separately from this product. Wiring them together or placing them in the same duct may cause induction, resulting in malfunction or damage. • Use adequate safety measures, for example fail-safe circuits. • Use a specified-sized wire when wiring. Do not connect wires other than those of the specification to the terminal block. • Do not connect a wire with an only twisted end directly to a terminal block. • For a power supply, use a DC power supply unit provided with a remedy, for example, safety ultralow voltage circuit, to prevent a high voltage from being generated. • Route so that power supply wires are as short as possible. • Use a power supply dedicated for this product, without sharing it with other products. • Before performing any of the following activities, be sure to turn off the product, or breakdown may result. - Connecting or wiring cables - Connecting or disconnecting connectors - Installing or removing Calibration ROM • Do not apply any loads to cables and connectors when wiring. • When inserting or removing an EtherCAT cable, do not put any stress on the calibration ROM. • Before turning ON the power after the product is connected, make sure that the power supply voltage is correct, there are no incorrect connections (e.g. load short-circuit) and the load current is appropriate. Incorrect wiring may result in breakdown of the product. • Handling fiber cables Use them in compliance with the following. This may result in damage to the fiber cable. - Fiber cable bend radiuses must be at least 20 mm. - Do not yank hard on a fiber cable. - Do not step on a fiber cable or place anything heavy on it. - Do not apply any twisting stress to the fiber cable. - Do not forcefully insert, or ben...
Sample 1
AutoNDA by SimpleDocs
Power Supply and Wiring. When using a commercially available switching regulator, make sure that the FG terminal is grounded. • If surge currents are present in the power lines, connect surge absorbers that suit the operating environment. • Use the specified voltage. If voltage exceeding the rating or AC voltage is applied, circuit parts may be burnt or rupture. • Cannot remove the Fiber interface of Sensor Head. If you accidentally remove it, need to repair. Use the optional extension fiber cable ZW-XF70□□R is suitable for the ZW-7000 series, and ZW-XF50□□R for the ZW-5000 series. Only one cable can be extended. • Be sure to use a Sensor Head and Calibration ROM with the same serial number. A pair with different serial numbers cannot operate normally. • Use the configuration software with the combination specified in this manual, or the system may operate faultily. • Do not shut down the power supply when saving any data into the memory built in the Sensor Controller, or the data may be corrupted. • While a fiber cable is not in use, be sure to attach the included protective cap to the connector of the fiber cable. Leaving it with the protective cap not attached may result in a malfunction due to the adhesion of foreign matter. • Make sure to initialize the Sensor Controller when connecting a different type Sensor Head from that which was connected the previous time the Sensor Controller was launched.
Sample 1

Related to Power Supply and Wiring

  • Power Supply The source of power for the VAS shall either be the vehicle battery or a rechargeable battery. Where provided, an additional rechargeable or non-rechargeable battery may be used. These batteries shall by no means supply energy to other parts of the vehicle electrical system.

  • Water Supply The system may or may not meet state and local requirements. It is the right and responsibility of Buyer to determine the compliance of the system with state and local requirements. [For additional information on this subject, request the “Water Supply and Waste Disposal Notification” form.]

  • All-Requirements Power Supply The service under which the Competitive Supplier provides all of the electrical energy, capacity, reserves, and ancillary services, transmission services, transmission and distribution losses, congestion management, and other such services or products necessary to provide firm power supply to Participating Consumers at the Point of Delivery.

  • TRANSPORT SERVICES Upon the conclusion of such multilateral negotiations, the Parties shall conduct a review for the purpose of discussing appropriate amendments to this Agreement so as to incorporate the results of such multilateral negotiations.

  • SHIPPING AND AIR TRANSPORT 1. Profits of an enterprise of a Contracting State from the operation of ships or aircraft in international traffic shall be taxable only in that State. 2. The provisions of paragraph 1 shall also apply to profits from the participation in a pool, a joint business or an international operating agency.

  • Logistics The Client shall arrange their own transportation and accommodation, unless Client and Performer agree otherwise. If requested, the Performer shall arrange transport within Ostrava, and provide accommodation in a hotel.

  • Interconnection Customer Provided Services The services provided by Interconnection Customer under this LGIA are set forth in Article 9.6 and Article 13.5. 1. Interconnection Customer shall be paid for such services in accordance with Article 11.6.

  • Direct Contracting Goods and works which the Association agrees meet the requirements for Direct Contracting may be procured in accordance with the provisions of said procurement method.

  • Light and Air Tenant agrees that no diminution of light, air or view by any structure which may hereafter be erected (whether or not by Landlord) shall entitle Tenant to any reduction of rent hereunder, result in any liability of Landlord to Tenant, or in any other way affect this Lease.

  • Telemedicine Services This plan covers clinically appropriate telemedicine services when the service is provided via remote access through an on-line service or other interactive audio and video telecommunications system in accordance with R.I. General Law § 27-81-1. Clinically appropriate telemedicine services may be obtained from a network or non- network provider, and from our designated telemedicine service provider. When you seek telemedicine services from our designated telemedicine service provider, the amount you pay is listed in the Summary of Medical Benefits. When you receive a covered healthcare service from a network or non-network provider via remote access, the amount you pay depends on the covered healthcare service you receive, as indicated in the Summary of Medical Benefits. For information about telemedicine services, our designated telemedicine service provider, and how to access telemedicine services, please visit our website or contact our Customer Service Department.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!