RAM and RAP SRL Sample Clauses

RAM and RAP SRL. For HMA wearing courses, limit the total combination of RAM and RAP to a maximum of 15% of the mixture by mass (weight) unless documentation of the SRL designation of the coarse aggregate in the RAM and RAP materials is provided to the DME and the RAM and RAP meet the specified SRL or can be blended for SRL as specified in Section 409.2(b)1.
AutoNDA by SimpleDocs

Related to RAM and RAP SRL

  • Unbundled Copper Sub-Loop (UCSL) is a copper facility of any length provided from the cross-box in the field up to and including the End User’s point of demarcation. If available, this facility will not have any intervening equipment such as load coils between the End User and the cross-box.

  • Unbundled Copper Loops (UCL) 2.4.1 BellSouth shall make available Unbundled Copper Loops (UCLs). The UCL is a copper twisted pair Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters) and is not intended to support any particular telecommunications service. The UCL will be offered in two types – Designed and Non-Designed.

  • Maximum Contractual Obligation The maximum obligation of COUNTY under this Agreement shall not exceed the amount of $970,800 or actual allowable costs, whichever is less. The estimated annual amount for each twelve (12) month period is as follows:

  • Extension of Concession Period Subject to the provisions of Clause 35.6, in the event that a material default or breach of this Agreement set forth in Clause 35.2 causes delay in achieving COD or leads to suspension of or reduction in collection of Fee, as the case may be, the Authority shall, in addition to payment of compensation under Clause 35.2, extend the Concession Period, such extension being equal in duration to the period by which COD was delayed or the collection of Fee remained suspended on account thereof, as the case may be.

  • Voice Grade Unbundled Copper Sub-Loop Unbundled Sub-Loop Distribution – Intrabuilding Network Cable (aka riser cable)

  • Unbundled Copper Loop Designed (UCL-D)

  • Unbundled Sub-Loop Distribution Intrabuilding Network Cable (USLD-INC) is the distribution facility owned or controlled by BellSouth inside a building or between buildings on the same property that is not separated by a public street or road. USLD-INC includes the facility from the cross connect device in the building equipment room up to and including the point of demarcation at the End User’s premises.

  • Unbundled Voice Loop – SL2 (UVL-SL2 Loops may be 2-wire or 4-wire circuits, shall have remote access test points, and will be designed with a DLR provided to NewPhone. SL2 circuits can be provisioned with loop start, ground start or reverse battery signaling. OC is provided as a standard feature on XX0 Xxxxx. The OC feature will allow NewPhone to coordinate the installation of the Loop with the disconnect of an existing customer’s service and/or number portability service. In these cases, BellSouth will perform the order conversion with standard order coordination at its discretion during normal work hours.

  • Unbundled Copper Loop – Designed (UCL-D) 2.4.2.1 The UCL-D will be provisioned as a dry copper twisted pair (2- or 4-wire) Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters).

  • Contractual Obligations Without limitation, the indemnity set forth in this Section 7.6 shall extend to any liability of any Indemnitee pursuant to a loan guaranty (except a guaranty by a Limited Partner of nonrecourse indebtedness of the Partnership or as otherwise provided in any such loan guaranty), contractual obligation for any indebtedness or other obligation or otherwise for any indebtedness of the Partnership or any Subsidiary of the Partnership (including, without limitation, any indebtedness which the Partnership or any Subsidiary of the Partnership has assumed or taken subject to), and the General Partner is hereby authorized and empowered, on behalf of the Partnership, to enter into one or more indemnification agreements consistent with the provisions of this Section 7.6 in favor of any Indemnitee having or potentially having liability for any such indebtedness.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!