Safety devices and safety functions Sample Clauses

Safety devices and safety functions. The technical measures needed to perform these functions will depend on their functioning under failure conditions within the E/E/PES, and are to be selected on the basis of risk assessment. If a safety device is activated, the machine shall stop at least in the direction of movement. Where a safety device at crushing or shearing points is activated, movement in the direction contrary to that of the hazardous movement shall be possible. It shall be possible to check the functioning of all safety devices. The activation of a safety device shall be indicated as long as the activation is in effect. Overtravel limit switches shall be designed as in EN 00000-0-0. It is possible to replace overtravel limit switches with encoder sensing of overtravel, provided that the system is designed in such a manner that the required SIL level, determined by risk assessment, is achieved. The minimum expected SIL level in such circumstances is SIL 3, unless the overtravel will result in no mechanical damage or injury to personnel. Safety circuits shall be configured in such a manner that the required SIL determined by means of risk assessment can be achieved even without position switches. Safety circuits which register the exceeding of specified travel paths, speeds, or loads, or unacceptable deviations from specified trajectories, which could cause a hazardous condition or damage the machinery installation shall initiate a secure emergency stop when activated. The stop category shall be established on the basis of risk assessment for the machinery installation in question. 8.3.4.1 Overtravel limits (limit switches) 8.3.4.2 Providing protection when characteristic loads are exceeded (Overload Protection) 8.3.4.3 Providing protection in underload and slack-wire situations 8.3.4.4 Providing protection when wear limits of screw jacks are reached 8.3.4.5 Providing protection when speed regulators fail 8.3.4.6 Providing protection when nominal speeds are exceeded
AutoNDA by SimpleDocs

Related to Safety devices and safety functions

  • Safety Devices All Products provided under the Contract shall be equipped with required safety devices to comply with all applicable codes, laws, and regulations that are in effect at the time of delivery.

  • Function of Joint Health and Safety Committee All incidents involving aggression or violence shall be brought to the attention of the Joint Health and Safety Committee. The Employer agrees that the Joint Health and Safety Committee shall concern itself with all matters relating to violence to staff.

  • Environmental, Health and Safety Matters (a) Comply in all material respects with all applicable Environmental Laws, including, without limitation, obtaining and complying with and maintaining any and all licenses, approvals, notifications, registrations or permits required by applicable Environmental Laws. For purposes of this Section 5.12(a), material noncompliance by the Company, any of its Subsidiaries or any tenant or subtenant, with any applicable Environmental Law shall be deemed not to constitute a breach of this covenant provided that, upon learning of any actual or suspected material noncompliance, the Company and the relevant Subsidiaries shall promptly undertake all reasonable efforts to achieve material compliance (or contest in good faith by appropriate proceedings the alleged violation or applicable Environmental Law at issue and (to the extent required by GAAP) provide on the books of the Company or any of its Subsidiaries, as the case may be, reserves in accordance with GAAP with respect thereto), and provided further that, in any case, such noncompliance, and any other noncompliance with applicable Environmental Law, individually or in the aggregate, could not reasonably be expected to have a Material Adverse Effect. (b) Promptly comply in all material respects with all lawful orders and directives of all Governmental Authorities regarding applicable Environmental Laws, except to the extent that the validity thereof is currently being contested in good faith by appropriate proceedings and (to the extent required by GAAP) reserves in accordance with GAAP with respect thereto have been provided on the books of the Company or any of its Subsidiaries, as the case may be. (c) Defend, indemnify and hold harmless the Administrative Agent and the Lenders, and their respective parents, subsidiaries, affiliates, employees, agents, officers and directors, from and against any claims, demands, penalties, fines, liabilities, settlements, damages, costs and expenses of whatever kind or nature, known or unknown, contingent or otherwise, arising out of, or in any way relating to the violation of, noncompliance with or liability under any Environmental Laws applicable to the Company or any of its Subsidiaries or any of their respective operations or properties, or any orders, requirements or demands of Governmental Authorities related thereto, including, without limitation, attorney’s and consultant’s fees, investigation and laboratory fees, response costs, court costs and litigation expenses, except to the extent that any of the foregoing arise out of the gross negligence or willful misconduct of (or, as determined pursuant to a claim initiated by the Company, breach in bad faith of its express obligations under the applicable Loan Documents by) the party seeking indemnification therefor, in each case, as determined by a final non-appealable judgment by a court of competent jurisdiction. This indemnity shall continue in full force and effect regardless of the termination of this Agreement.

  • Environmental, Health and Safety Laws There does not exist any violation by the Borrower or any of its Subsidiaries of any applicable federal, state or local law, rule or regulation or order of any government, governmental department, board, agency or other instrumentality relating to environmental, pollution, health or safety matters which has, will or threatens to impose a material liability on the Borrower or any of its Subsidiaries or which has required or would require a material expenditure by the Borrower or any of its Subsidiaries to cure. Neither the Borrower nor any of its Subsidiaries has received any notice to the effect that any part of such Person’s operations or properties is not in material compliance with any such law, rule, regulation or order or notice that it or its property is the subject of any governmental investigation evaluating whether any remedial action is needed to respond to any release of any toxic or hazardous waste or substance into the environment, which non-compliance or remedial action could reasonably be expected to constitute a Material Adverse Occurrence. Except as set out on Schedule 4.7 of the Disclosure Schedules, the Borrower does not have knowledge that it, any of its Subsidiaries or any of their respective property will become subject to environmental laws or regulations during the term of this Agreement, compliance with which could reasonably be expected to require significant Capital Expenditures or to constitute a Material Adverse Occurrence.

  • Environmental Health and Safety i. Environment, Health and Safety Performance. Seller acknowledges and accepts full and sole responsibility to maintain an environment, health and safety management system ("EMS") appropriate for its business throughout the performance of this Contract. Buyer expects that Seller’s EMS shall promote health and safety, environmental stewardship, and pollution prevention by appropriate source reduction strategies. Seller shall convey the requirement of this clause to its suppliers. Seller shall not deliver goods that contain asbestos mineral fibers.

  • Environment, Health, and Safety (a) To the Knowledge of AIDEA and the Acquired Companies, except as disclosed in Disclosure Schedules 3.16(b), (d), and (e), the Acquired Companies have complied with all Environmental, Health, and Safety Laws. No action, suit, proceeding, hearing, investigation, charge, complaint, claim, demand, or notice has been filed or commenced against any of the Acquired Companies alleging any failure to so comply. Without limiting the generality of the preceding sentence, the Acquired Companies, to the Knowledge of AIDEA and the Acquired Companies, have obtained and been in compliance with all of the terms and conditions of all permits, licenses, and other authorizations that are required under, and have complied with all other limitations, restrictions, conditions, standards, prohibitions, requirements, obligations, schedules, and timetables that are contained in, all Environmental, Health, and Safety Laws. (b) Except as disclosed in Disclosure Schedule 3.16(b), neither the Acquired Companies nor AIDEA with respect to the Acquired Companies, to the Knowledge of AIDEA and the Acquired Companies, has any Liability arising out of events or circumstances occurring under any Environmental, Health, and Safety Laws for contamination of, damage to, or polluting any site, location, property, natural resources, the air, or any body of water (surface or subsurface), or for any illness of, or personal injury to, or death of, any employee or other individual related to the foregoing. (c) To the Knowledge of AIDEA and the Acquired Companies, all equipment and personal property owned, leased, or used in the Operations are and have been free of hydrocarbon contamination, asbestos, PCBs, dioxins, and any other hazardous, toxic, radioactive, or dangerous substances, except for the liquefied natural gas and compressed natural gas the Acquired Companies produce, store, and handle, and except for the fuel, lubricants, refrigerants, and solvents that are used in the ordinary course of business in conducting the Operations. The liquefied natural gas and compressed natural gas of the Acquired Companies, and the fuel, lubricants, refrigerants, and solvents used in its Operations, have all been stored, handled, transported, used, and disposed of in accordance with all Environmental, Health, and Safety Laws and consistent with all standard industry practices. (d) Except as disclosed on Disclosure Schedule 3.16(d), all real property the Acquired Companies owns is, to the Knowledge of AIDEA and the Acquired Companies, free from contamination by any substance regulated under, or defined as or considered “hazardous” or “toxic” or “radioactive” or “contamination” or “pollution” under, any Environmental, Health, and Safety Laws, including but not limited to hydrocarbons, asbestos, PCBs, and dioxins. AIDEA has provided IGU with true and complete copies of all environmental assessments, studies, and reports (1) of which AIDEA and the Acquired Companies have Knowledge and (2) that reference the real property any of the Acquired Companies owns, leases, or uses. Although neither AIDEA nor the Acquired Companies has conducted any environmental assessments regarding the leased real property used by the Acquired Companies, neither AIDEA nor the Acquired Companies has Knowledge of any environmental contamination on or under the portions of any leased or used real property where any of the Operations have been conducted. (e) Except as disclosed on Disclosure Schedule 3.16(e), neither the Acquired Companies nor AIDEA has Knowledge of any leak, spill, release, discharge, or disposal of any substance regulated under, or defined as or considered “hazardous” or “toxic” or “radioactive” or “contamination” or “pollution” under any Environmental, Health, and Safety Laws that has occurred on, in, or under the real property any of the Acquired Companies owns, leases, or uses, or has ever owned, leased, or used, in conducting the Operations, that was reportable or should have been reported to any government or governmental agency, or that was or could have been subject to clean up or remediation, under any Environmental, Health, and Safety Laws. (f) Except as disclosed on Disclosure Schedule 3.16(f), to the Knowledge of AIDEA and the Acquired Companies, there is no underground storage tank present on any real property any of the Acquired Companies owns, leases, or uses or has owned, leased or used, in conducting the Operations.

  • CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.

  • Safety Boots Each employee, after 3 months’ continuous service, will be reimbursed (on production of a receipt), the cost of one pair of safety boots (approved by the employer), in each year, to a maximum of $110.00. All protective clothing such as wet weather jackets, safety helmets, welding jackets, welding xxxxxxx, welding gauntlets, rubber boots, etc, (which remain the property of the Company), will be supplied on all occasions deemed necessary.

  • Electrical appliance safety The Hirer shall ensure that any electrical appliances brought by them to the premises and used there shall be safe, in good working order, and used in a safe manner in accordance with the Electricity at Work Regulations 1989. Where a residual circuit breaker is provided the hirer must make use of it in the interests of public safety.

  • Health and Safety Plan Consultant shall prepare and submit a Health and Safety Plan (“HASP”) for the portion of Consultant’s work that will involve field work, assessments, or investigations of certain Project elements. The HASP shall describe how Consultant plans to complete field work, assessments, and/or investigations at the RWF. Consultant’s HASP must comply with the CIP HASP and shall be updated as new conditions are encountered.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!