Weighing 7.1. In order to calculate the quantity of Grain delivered to a Port Terminal Facility: (a) all Grain delivered by road to the Port Terminal Facilities for unloading must be weighed using CBH’s weighing facilities operated by CBH personnel recording the gross and tare weights of the road vehicles containing the loads of Grain; (b) if the Grain is delivered by rail from a CBH Site upcountry, the weight will be determined by referencing the weight of the load as determined by CBH personnel at the relevant upcountry Site (“CBH Weight”); and (c) if the Grain is delivered by rail from a third party site and where the Port Terminal Facilities have such facilities, CBH will batch weigh the Grain unloaded from rail vehicles into the grid. 7.2. If Grain is delivered a Port Terminal Facility by rail pursuant to clause 7.1(b) of this Schedule 7, CBH may elect to conduct an audit and batch weigh the Grain delivered to the Port Terminal Facility. If, following an audit by CBH under this clause 7.2 of this Schedule 7, there is a discrepancy of more than 2.5% between the CBH Weight and the weight determined by CBH at Port (“Weight Shortfall”), CBH may deduct the relevant Weight Shortfall from the Customer’s Grain Entitlement and charge the Customer the Rail Weighing Fee as set out in the Fees and Charges Schedule. 7.3. In all cases, CBH must provide the Customer with a weighbridge ticket or other statement certifying the weight and quantity of Grain delivered to the Port Terminal Facility and confirming the name of the person in whose name the Grain is delivered based on the information contained in the Customer’s Direct to Port Delivery Declaration Form and Direct to Port Sample Declaration Form provided to CBH at or prior to the delivery of each load of Grain at the Port Terminal Facility.
Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.64 – DEBARMENT AND SUSPENSION CERTIFICATION (3/18). Pursuant to 2 CFR 180 and 2 CFR 417, Purchaser shall certify and obtain certifications from its Subcontractors regarding debarment, suspension, ineligibility, and voluntary exclusion, including additional Subcontractors obtained after award of this contract. “Subcontractors” are participants in lower tier covered transactions. Purchaser may rely upon a certification of a prospective Subcontractor that it is not proposed for debarment under 48 CFR 9.4, debarred, suspended, ineligible, or voluntarily excluded from participating in covered transactions or timber sales, unless Purchaser knows that the certification is erroneous. Purchaser shall keep the certifications of its Subcontractors on file until timber sale Termination Date and any extensions thereof, and will provide a copy at the written request of Contracting Officer. Nothing contained in the foregoing shall be construed to require establishment of a system of records in order to render in good faith the certification required by this Subsection. The knowledge and information of Purchaser is not required to exceed that which is normally possessed by a prudent person in the ordinary course of business dealings. If Purchaser knowingly enters into a timber sale transaction with a person who is proposed for debarment under 48 CFR 9.4, suspended, debarred, ineligible, or voluntarily excluded from participation in covered transactions or timber sales, in addition to other remedies available to the Government, Forest Service may pursue available remedies, including suspension and/or debarment. Contracting Officer shall provide a copy of Forms AD-1047 Certification Regarding Debarment, Suspension and Other Responsibility Matters – Primary Covered Transactions and AD-1048 Certification Regarding Debarment, Suspension, Ineligibility and Voluntary Exclusion – Lower Tier Covered Transactions to the Purchaser. Purchaser shall complete form AD-1047 and provide to the Contracting Officer upon request. Purchaser shall require each subcontractor to complete form AD-1048 and provide to the Contracting Officer upon request.
Containers The marine and intermodal cargo containers either owned or leased by the Borrower and employed by the Borrower in the conduct of its business, including, without limitation, refrigerated, dry van, tank, open top and flat rack containers and refrigeration units and generator sets associated therewith, but excluding any chassis for such containers.
Fixtures and Fittings 8.13.1 Not to remove any of the Fixtures and Fittings from the Premises to store the same in the loft, basement or garage (if any) without obtaining the Landlord’s prior written consent, such consent not to be unreasonably withheld, and then to ensure that any such items are stored safely and upon vacating the Premises, to leave the same in the places in which they were on the Commencement Date. 8.13.2 Not to remove the Fixtures and Fittings as specified in the Inventory and Schedule of Condition or any part of them or any substitute Fixtures and Fittings from the Premises and not to bring onto the Premises the Tenant’s own equipment or effects without the prior written consent of the Landlord, such consent not to be unreasonably withheld.
Packing 3.9.1 The tenderer shall provide such packing of the Goods as is required to prevent their damage or deterioration during transit to their final destination, as indicated in the Contract. 3.9.2 The packing, marking, and documentation within and outside the packages shall comply strictly with such special requirements as shall be expressly provided for in the Contract
Tooling Unless otherwise specified in this Agreement, all tooling and/or all other articles required for the performance hereof shall be furnished by Seller, maintained in good condition and replaced when necessary at Seller's expense. If NETAPP agrees to pay Seller for special tooling or other items either separately or as a stated part of the unit price of Goods purchased herein, title to same shall be and remain in NETAPP upon payment therefore.
Samples The Contractor shall submit the following samples of Materials and relevant information to the Authority’s Engineer for pre-construction review: (a) manufacturer's test reports and standard samples of manufactured Materials; and (b) samples of such other Materials as the Authority’s Engineer may require.
Calibration The comparison of a measurement system or device of unverified accuracy with a measurement system of known and greater accuracy to detect deviation of the unverified measurement system from required performance specifications (of the unverified measurement system or device) and to quantify all measured values to applicable units of the international system of units.
Painting All exterior surfaces and materials requiring paint shall be prime coated plus 2 coats of Xxxxxxx Xxxxxxxx Pro-Mar alkyd flat exterior finish, or Xxxxxxx-Xxxxxxxx SWP exterior gloss paint. 10.1 Wall Corner Guards: Provide clear plastic guards up to 60” AFF on all outside corners to protect vinyl wall covering.
Appliances The Landlord shall: (check one) ☐ - Provide the following appliances: [ENTER APPLIANCES] ☐ - Not provide any appliances.
