Contract Governance Any contract made or entered into by the TIPS is subject to and is to be governed by Section 271.151 et seq, Tex Lo Code. Otherwise, TIPS does not waive its governmental immunities from suit or liability except to the extent expressly by other applicable laws in clear and unambiguous language. Yes, I Agree (Yes) 9
Project Governance (a) If advised in writing by the Ministry the Recipient will:
Shared Governance The parties shall develop a variety of shared governance models which schools may consider. Schools shall select a model that best suits their needs or the staff may develop an alternative model of governance with direct involvement by teachers, other staff and community representatives. Staff approval and commitment to the model is essential. The selected model of governance will be specifically described in each school's improvement plan.
Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
GOVERNANCE AND REPORTING Measure 3a Is the school complying with governance requirements? Meets Standard: The school materially complies with applicable laws, rules, regulations and provisions of the charter contract relating to governance by its board, including but not limited to: • Governing board composition and membership requirements pursuant to Ch. 302D, HRS • Governing board policies • Governing board reporting requirements • Procurement policies • State Ethics Code (Ch. 84, HRS), including conflict of interest policy Measure 3b Is the school holding management accountable? Meets Standard: The school materially complies with applicable laws, rules, regulations and provisions of the charter contract relating to oversight of school management, including but not limited to: • (For Education Service Providers [ESPs]) maintaining authority over management, holding it accountable for performance as agreed under a written performance agreement and requiring annual financial reports of the ESP • (For Others) oversight of management that includes holding it accountable for performance expectations that may or may not be agreed to under a written performance agreement Measure 3c Is the school complying with data and reporting requirements? Meets Standard: The school materially complies with applicable laws, rules, regulations and provisions of the charter contract relating to relevant reporting requirements to the State Public Charter School Commission, State Department of Education as the State Education Agency (SEA) and sole Local Education Agency (LEA) and/or federal authorities, including but not limited to: • Compliance with minimum educational data reporting standards established by the BOE • Maintaining and reporting accurate enrollment and attendance data • Maintaining and reporting accurate personnel data • Annual reporting and immediate notice requirements • Additional information requested by the State Public Charter School Commission
Function of Joint Health and Safety Committee All incidents involving aggression or violence shall be brought to the attention of the Joint Health and Safety Committee. The Employer agrees that the Joint Health and Safety Committee shall concern itself with all matters relating to violence to staff.
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Responsibilities of Committee The Committee shall not have jurisdiction over wages or any other matter of collective bargaining, including the administration of this Agreement. The Committee shall not supersede the activities of any other committee of the Union or of the Employer and shall not have the power to bind either the Union or its members or the Employer to any decisions or conclusions reached in their discussions. The Committee shall have the power to make recommendations to the Union and the Employer on the following general matters:
Restricted Use By Outsourcers / Facilities Management, Service Bureaus or Other Third Parties Outsourcers, facilities management or service bureaus retained by Licensee shall have the right to use the Product to maintain Licensee’s business operations, including data processing, for the time period that they are engaged in such activities, provided that: 1) Licensee gives notice to Contractor of such party, site of intended use of the Product, and means of access; and 2) such party has executed, or agrees to execute, the Product manufacturer’s standard nondisclosure or restricted use agreement which executed agreement shall be accepted by the Contractor (“Non-Disclosure Agreement”); and 3) if such party is engaged in the business of facility management, outsourcing, service bureau or other services, such third party will maintain a logical or physical partition within its computer system so as to restrict use and access to the program to that portion solely dedicated to beneficial use for Licensee. In no event shall Licensee assume any liability for third party’s compliance with the terms of the Non-Disclosure Agreement, nor shall the Non-Disclosure Agreement create or impose any liabilities on the State or Licensee. Any third party with whom a Licensee has a relationship for a state function or business operation, shall have the temporary right to use Product (e.g., JAVA Applets), provided that such use shall be limited to the time period during which the third party is using the Product for the function or business activity.
