Topographic Survey The Professional shall obtain a topographic and utility survey as described below.
4.1.1. The Professional shall tie in all existing surface topographic features and structures within the survey limits shown in Figure 1. This survey shall include: tops of curbs, edges of pavement, pavement materials, driveways, sidewalks, retaining walls, drainage structures (top, edges and flow line), channels and drainage ways (tops, toes and flow line), manholes (rim, flow lines and diameters of pipes, type of material and photographs of the inside of manholes and drainage structures), including the same survey data for upstream and downstream manholes and structures that are outside of the survey limits for all gravity wastewater and drainage lines within the survey limits. Visible valves, meters, clean-outs, slabs, utility signs, utility poles and structures, fences, landscaping features, shrubbery, trees (including the approximate drip-line), tree canopies, buildings (edges within the survey limits) mailboxes, etc. Trees shall be tagged and tabulated by size and species specific in compliance with the City of New Braunfels Tree Preservation ordinance as defined in the City of New Braunfels Zoning Ordinance Chapter 5.3- 5i. The survey limits shall extend approximately 100 feet on intersecting streets. The Professional shall provide sufficient ground shots to create one (1) foot contours for the Project.
4.1.2. The Professional shall conduct a utility survey and locate existing utilities within the Project boundary in Figure 1. The Professional shall contact all utility service providers by calling Texas 811 and the NBU Project Manager to coordinate flagging of existing franchise utilities. The Professional shall request drawings of existing agency and municipal owned utilities and shall include locations of these utilities in the survey. The Professional shall tie in the locations of the discovered utilities on the survey. The Professional shall bear all costs for the Services associated with utility locates.
4.1.3. The Professional shall locate up to ten (10) geotechnical borings and tie them in to the Project survey.
4.1.4. The Professional shall set and install control points and/or benchmarks as required for the survey work (minimum 1-foot intervals). The Professional shall provide horizontal and vertical coordinates of the benchmarks in the required coordinate system and datum and show the benchmarks on the survey drawing.
4.1.5. The Professional shall research and review adjoining plats and deeds along the survey corridor. The Professional shall locate property corners and identify existing right of way (“ROW”), along the survey corridor, based on found monuments and record documents.
Adverse Weather Shall be only weather that satisfies all of the following conditions: (1) unusually severe precipitation, sleet, snow, hail, or extreme temperature or air conditions in excess of the norm for the location and time of year it occurred based on the closest weather station data averaged over the past five years, (2) that is unanticipated and would cause unsafe work conditions and/or is unsuitable for scheduled work that should not be performed during inclement weather (i.e., exterior finishes), and (3) at the Project.
Geotechnical Investigation Perform in accordance with the City Design Manual and other City requirements as designated in writing by the Director.
Third Party Components The Products and Services may contain third party components (including open source software) subject to separate license agreements. To the limited extent a third party license expressly supersedes this XXXX, such third party license governs Customer’s use of that third party component.
Field The term “
Geotechnical Engineer « »« » « » « » « » « »
Manufacturing Technology Transfer Upon AbbVie’s written request with respect to a given Collaboration CAR-T Product and Licensed Product, Caribou shall effect a full transfer to AbbVie or its designee (which designee may be an Affiliate or a Third Party Provider) of all Materials and Know-How Controlled by Caribou relating to the then-current process for the Manufacture of such Collaboration CAR-T Product and any corresponding Licensed Products (each, a “Manufacturing Process”). Caribou shall provide, shall cause its Affiliates to provide, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all Third Party Providers to provide, all reasonable assistance requested by AbbVie to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to implement each Manufacturing Process at the facilities designated by AbbVie. If requested by AbbVie, such assistance shall include facilitating the entering into of agreements with applicable Third Party suppliers relating to such Collaboration CAR-T Product and any corresponding Licensed Products. Without limitation of the foregoing, in connection with the Manufacturing Process and related transfer:
(a) Caribou shall, and shall cause its Affiliates to, make available to AbbVie (or its Affiliate or designated Third Party Provider, as applicable), and shall use Commercially Reasonable Efforts to assist AbbVie in causing all Third Party Providers to make available to AbbVie, from time to time as AbbVie may request, all Materials and Manufacturing-related Know-How Controlled by Caribou relating to each Manufacturing Process, including methods, reagents and processes and testing/characterization Know-How, and all documentation constituting material support, performance advice, shop practice, standard operating procedures, specifications as to Materials to be used, and control methods, that are necessary or reasonably useful to enable AbbVie (or its Affiliate or designated Third Party manufacturer, as applicable) to use and practice such Manufacturing Process;
(b) Caribou shall cause all appropriate employees and representatives of Caribou and its Affiliates, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all appropriate employees and representatives of Third Party Providers, to meet with employees or representatives of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) at the applicable manufacturing facility at mutually convenient times to assist with the working up and use of each Manufacturing Process and with the training of the personnel of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to the extent necessary or reasonably useful to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to use and practice such Manufacturing Process;
(c) Without limiting the generality of this Section 4.4.2, Caribou shall cause all appropriate analytical and quality control laboratory employees and representatives of Caribou and its Affiliates, and shall use Commercially Reasonable Efforts to assist AbbVie in causing all appropriate analytical and quality control laboratory employees and representatives of Third Party Providers, to meet with employees or representatives of AbbVie (or its Affiliate or designated Third Party Provider, as applicable) at the applicable manufacturing facility and make available all necessary equipment, at mutually convenient times, to support and execute the provision of all applicable analytical methods and the validation thereof (including all applicable Know-How, Information and Materials Controlled by Caribou, and sufficient supplies of all primary and other reference standards);
(d) Caribou shall, and shall cause its Affiliates to, take such steps, and shall use Commercially Reasonable Efforts to assist AbbVie in causing Third Party Providers take such steps, as are necessary or reasonably useful to assist AbbVie (or its Affiliate or designated Third Party Provider, as applicable) in obtaining any necessary licenses, permits or approvals from Regulatory Authorities with respect to the Manufacture of the applicable Collaboration CAR-T Products and corresponding Licensed Products at the applicable facilities; and
(e) Caribou shall, and shall cause its Affiliates to, provide, and shall use Commercially Reasonable Efforts to assist AbbVie in causing Third Party Providers to provide, such other assistance as AbbVie (or its Affiliate or designated Third Party Provider, as applicable) may reasonably request to enable AbbVie (or its Affiliate or designated Third Party Provider, as applicable) to use and practice each Manufacturing Process and otherwise to Manufacture the applicable Collaboration CAR-T Products and corresponding Licensed Products.
Background Screening VENDOR shall comply with all requirements of Sections 1012.32 and 1012.465, Florida Statutes, and all of its personnel who (1) are to be permitted access to school grounds when students are present, (2) will have direct contact with students, or (3) have access or control of school funds, will successfully complete the background screening required by the referenced statutes and meet the standards established by the statutes. This background screening will be conducted by SBBC in advance of VENDOR or its personnel providing any services under the conditions described in the previous sentence. VENDOR shall bear the cost of acquiring the background screening required by Section 1012.32, Florida Statutes, and any fee imposed by the Florida Department of Law Enforcement to maintain the fingerprints provided with respect to VENDOR and its personnel. The parties agree that the failure of VENDOR to perform any of the duties described in this section shall constitute a material breach of this Agreement entitling SBBC to terminate immediately with no further responsibilities or duties to perform under this Agreement. VENDOR agrees to indemnify and hold harmless SBBC, its officers and employees from any liability in the form of physical or mental injury, death or property damage resulting from VENDOR’s failure to comply with the requirements of this section or with Sections 1012.32 and 1012.465, Florida Statutes.
Engineering Forest Service completed survey and design for Specified Roads prior to timber sale advertisement, unless otherwise shown in A8 or Purchaser survey and design are specified in A7. On those roads for which Forest Service completes the design during the contract, the design quantities shall be used as the basis for revising estimated costs stated in the Schedule of Items and adjusting Timber Sale Account.
(a) A7 to show Purchaser’s performance responsibility.
(b) The Schedule of Items to include costs of survey and design, as provided under B5.24, and adjust Timber Sale Account, as provided in B5.
Geological and archaeological finds It is expressly agreed that mining, geological or archaeological rights do not form part of this Agreement with the Contractor for the Works, and the Contractor hereby acknowledges that it shall not have any mining rights or interest in the underlying minerals, fossils, antiquities, structures or other remnants or things either of particular geological or archaeological interest and that such rights, interest and property on or under the Site shall vest in and belong to the Authority or the concerned Government Instrumentality. The Contractor shall take all reasonable precautions to prevent its workmen or any other person from removing or damaging such interest or property and shall inform the Authority forthwith of the discovery thereof and comply with such instructions as the concerned Government Instrumentality may reasonably give for the removal of such property. For the avoidance of doubt, it is agreed that any reasonable expenses incurred by the Contractor hereunder shall be reimbursed by the Authority. It is also agreed that the Authority shall procure that the instructions hereunder are issued by the concerned Government Instrumentality within a reasonable period.
