Common use of Transitional provisions6 Clause in Contracts

Transitional provisions6. 14.1. As from 24 months after the official date of entry into force of UN Regulation No. 148, Contracting Parties applying this Regulation shall cease to grant approvals to this Regulation. 14.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of approval to this and any previous series of amendments of this Regulation. 14.3. Contracting Parties applying this Regulation shall continue to grant approvals for devices on basis of this and any previous series of amendments to this Regulation, provided that the devices are intended as replacements for fitting to vehicles in use. 14.4. Contracting Parties applying this Regulation shall continue to allow fitting or use on a vehicle in use of a device approved to this Regulation as amended by any previous series of amendments, provided that the device is intended for replacement. Front and rear position lamps, end-outline marker lamps and stop-lamps: minimum angles required for light distribution in space of these lamps7 In all cases, the minimum vertical angles of light distribution in space are 15° above and 15° below the horizontal for all categories of devices included in this Regulation, except: (a) For lamps intended to be installed with their H plane at a mounting height less than 750 mm above the ground, for which they are 15° above and 5° below the horizontal; (b) Optional lamps intended to be installed with their H plane at a mounting height more than 2,100 mm above the ground, for which they are 5° above and 15° below the horizontal; (c) For category S3 or S4 stop lamp for which they are 10° above and 5° below the horizontal. Under the H plane for front position lamps intended to be installed with this plane at a mounting height less than 750 mm above ground. Front position lamps Front end outline marker lamp (AM) R ear end outline marker lamp (RM1, RM2) Rear position lamps Under the H plane for rear position lamps intended to be installed with this plane at a mounting height less than 750 mm above ground. S top-lamps (S1 and S2) Under the H plane for stop lamps (S1 and S2) intended to be installed with this plane at a mounting height less than 750 mm above ground. 20° 45° Stop-lamps (S3 and S4) (Maximum format: A4 (210 x 297 mm)) issued by: Name of Administration: ...................................... ...................................... ...................................... Concerning:0 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of device pursuant to UN Regulation No. 7

Transitional provisions6. 14.1. As from 24 months after the official date of entry into force of UN Regulation No. 148, Contracting Parties applying this Regulation shall cease to grant approvals to this Regulation. 14.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of approval to this and any previous series of amendments of this Regulation. 14.3. Contracting Parties applying this Regulation shall continue to grant approvals for devices on basis of this and any previous series of amendments to this Regulation, provided that the devices are intended as replacements for fitting to vehicles in use. 14.4. Contracting Parties applying this Regulation shall continue to allow fitting or use on a vehicle in use of a device approved to this Regulation as amended by any previous series of amendments, provided that the device is intended for replacement. 6 The 03 series of amendments does not require changes in the approval number (TRANS/WP.29/815, para. 82). Front and rear position lamps, end-outline marker lamps and stop-lamps: minimum angles required for light distribution in space of these lamps7 lamps1 In all cases, the minimum vertical angles of light distribution in space are 15° above and 15° below the horizontal for all categories of devices included in this Regulation, except: (a) For lamps intended to be installed with their H plane at a mounting height less than 750 mm above the ground, for which they are 15° above and 5° below the horizontal; (b) Optional lamps intended to be installed with their H plane at a mounting height more than 2,100 mm above the ground, for which they are 5° above and 15° below the horizontal; (c) For category S3 or S4 stop lamp for which they are 10° above and 5° below the horizontal. 45° 80° Reference axis Front position lamps 20° 80° Under the H plane for front position lamps intended to be installed with this plane at a mounting height less than 750 mm above ground. Front position lamps Reference axis 1 The angles shown in these diagrams are correct for devices to be mounted on the right side of the vehicle. The arrows point to the front of the vehicle. Front end outline marker lamp (AM) R ear Rear end outline marker lamp (RM1, RM2) Rear position lamps 80° Driving direction 80°8 20° Reference axisReference Under the H plane for rear position lamps intended to be installed with this plane at a mounting height less than 750 mm above ground. S topStop-lamps (S1 and S2) 45° 45° Under the H plane for stop lamps (S1 and S2) intended to be installed with this plane at a mounting height less than 750 mm above ground. 20° 45° Stop-lamps (S3 and S4) (Maximum format: A4 (210 x 297 mm)) issued by: Name of Administration: ...................................... ...................................... ...................................... Concerning:0 Concerning:2 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of device pursuant to UN Regulation No. 7

Transitional provisions6. 14.1. As from 24 months after the official date of entry into force of UN Regulation No. 148, Contracting Parties applying this Regulation shall cease to grant approvals to this Regulation. 14.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of approval to this and any previous series of amendments of this Regulation. 14.3. Contracting Parties applying this Regulation shall continue to grant approvals for devices on basis of this and any previous series of amendments to this Regulation, provided that the devices are intended as replacements for fitting to vehicles in use. 14.4. Contracting Parties applying this Regulation shall continue to allow fitting or use on a vehicle in use of a device approved to this Regulation as amended by any previous series of amendments, provided that the device is intended for replacement. Front and rear position lamps, end-outline marker lamps and stop-lampsCategories of direction indicators: minimum Minimum angles required for light distribution in space of these lamps7 Categories of direction indicators7 In all cases, the minimum vertical angles of light distribution in space of direction indicator lamps are 15° above and 15° below the horizontal for all categories of devices included in this Regulation, except: (a) For Direction indicator lamps intended to be installed with their the H plane of the lamp at a mounting height of less than 750 mm above the ground, for which they are 15° above and 5° below the horizontal; (b) Optional direction indicator lamps intended to be installed with their the H plane of the lamp at a mounting height of more than 2,100 2100 mm above the ground, for which they are 5° above and 15° below the horizontal; (c) For category S3 or S4 stop lamp Direction indicator lamps of Category 6, for which they are 1030° above and 5° below the horizontal. Under Minimum horizontal visibility angles Direction indicators for the H plane for front position lamps intended to be installed with this plane of the vehicle Category 1: For use at a mounting height distance not less than 750 40 mm above ground. Front position lamps Front end outline marker lamp (AM) R ear end outline marker lamp (RM1, RM2) Rear position lamps Under from the H plane for rear position lamps intended to be installed with this plane dipped-beam headlamp and/or the front fog lamp; Category 1a: For use at a mounting height distance greater than 20 mm but less than 750 40 mm above ground. S top-lamps (S1 and S2) Under from the H plane for stop lamps (S1 and S2) intended to be installed with this plane at a mounting height less than 750 mm above ground. 20° 45° Stop-lamps (S3 and S4) (Maximum format: A4 (210 x 297 mm)) issued by: Name of Administration: ...................................... ...................................... ...................................... Concerning:0 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of device pursuant to UN Regulation No. 7dipped‑beam headlamp and/or the front fog lamp;

Transitional provisions6. 14.1. As from 24 months after the official date of entry into force of UN Regulation No. 148, Contracting Parties applying this Regulation shall cease to grant approvals to this Regulation. 14.2. Contracting Parties applying this Regulation shall not refuse to grant extensions of approval to this and any previous series of amendments of this Regulation. 14.3. Contracting Parties applying this Regulation shall continue to grant approvals for devices on basis of this and any previous series of amendments to this Regulation, provided that the devices are intended as replacements for fitting to vehicles in use. 14.4. Contracting Parties applying this Regulation shall continue to allow fitting or use on a vehicle in use of a device approved to this Regulation as amended by any previous series of amendments, provided that the device is intended for replacement. Front and rear position lamps6 The 02 series of amendments does not require changes in the approval number (TRANS/WP.29/815, end-outline marker lamps and stop-lampspara. 82). Annex 1 Categories of direction indicators: minimum Minimum angles required for light distribution in space of these lamps7 Categories of direction indicators1 In all cases, the minimum vertical angles of light distribution in space of direction indicator lamps are 15° above and 15° below the horizontal for all categories of devices included in this Regulation, except: (a) For Direction indicator lamps intended to be installed with their the H plane of the lamp at a mounting height of less than 750 mm above the ground, for which they are 15° above and 5° below the horizontal; (b) Optional direction indicator lamps intended to be installed with their the H plane of the lamp at a mounting height of more than 2,100 2100 mm above the ground, for which they are 5° above and 15° below the horizontal; (c) For category S3 or S4 stop lamp Direction indicator lamps of Category 6, for which they are 1030° above and 5° below the horizontal. Under Minimum horizontal visibility angles Direction indicators for the H plane for front position lamps intended to be installed with this plane of the vehicle Category 1: For use at a mounting height distance not less than 750 40 mm above ground. Front position lamps Front end outline marker lamp (AM) R ear end outline marker lamp (RM1, RM2) Rear position lamps Under from the H plane for rear position lamps intended to be installed with this plane dipped-beam headlamp and/or the front fog lamp; Category 1a: For use at a mounting height distance greater than 20 mm but less than 750 40 mm above ground. S topfrom the dipped-lamps (S1 and S2) Under beam headlamp and/or the H plane for stop lamps (S1 and S2) intended to be installed with this plane at a mounting height less than 750 mm above ground. 20° 45° Stop-lamps (S3 and S4) (Maximum format: A4 (210 x 297 mm)) issued by: Name of Administration: ...................................... ...................................... ...................................... Concerning:0 Approval granted Approval extended Approval refused Approval withdrawn Production definitively discontinued of a type of device pursuant to UN Regulation No. 7front fog lamp;