WORK TO BE PERFORMED The Contractor shall do all work and furnish all labor, tools, materials, supplies and equipment for the 2018 Replacement Well 3 Drilling Project (“Work”) in accordance with, and as described in the plans, specifications, drawings, instructions and other documents provided by the City, as amended which are by this reference incorporated herein and made part hereof (the “Contract Documents”). To the extent applicable or reasonably necessary to interpret the Work, the most recent publication of the Standard Specifications for Road, Bridge and Municipal Construction of the Washington State Department of Transportation (see xxxx://xxx.xxxxx.xx.xxx/Publications/Manuals/M41-10.htm) is incorporated into the Contract Documents. All changes in the work shall be performed in accord with the Contract Documents, unless determined otherwise by the City. The Contractor, as set forth in the Contractor’s bid proposal attached hereto as Exhibit A (the "Bid Proposal"), shall assume and be responsible for the cost and expense of all Work provided in the and Contract Documents, except those items agreed in writing to be furnished by the City of Xxxxxx. The Mayor or designee shall administer and be the primary contact for Contractor. Prior to commencement of work, Contractor shall contact the Mayor or designee to review the Work, schedule, and time of completion. Contractor shall receive written authorization from the City to proceed with the Work. Upon notice from the Mayor or designee, Contractor shall promptly commence Work, complete the same in a timely manner, and cure any failure in performance under this Agreement. All Work shall be performed in conformance with the Contract Documents, City and State standards and Bid Proposal. Contractor acknowledges review of the Contract Documents and accepts the same. In the event of a conflict between the Contract Documents, City and State standards or Bid Proposal, they shall be interpreted and given precedence in the order listed herein.
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.
CORRECTIVE MEASURE The contractor shall repair any deficiencies in excess of the performance guideline.
Method of Measurement The harmonics emission on AC power lines generated by the vehicle representative of its type shall be measured using the method described in Annex 11. The method of measurement shall be defined by the vehicle manufacturer in accordance with the Technical Service.
Temperature Measurement Temperature will be measured by the nearest automatic Melbourne Bureau of Meteorology Monitoring Station for example (but not limited to): Melbourne, Moorabbin, Dunns Hill, Melbourne Airport, Frankston, and Point Xxxxxx. At the commencement of each project, the onsite management and employee representatives shall agree which is to be the applicable automatic weather monitoring station.
WORK TOOLS 5.01 All Employees must have all the necessary hand tools listed in the Master Agreement (Employee Tool List). Replacement will be the responsibility of the Employee. APPENDIX TO THE ONTARIO PROVINCIAL AGREEMENT OF THE I.C.I. SECTOR OF THE CONSTRUCTION INDUSTRY FOR OSHAWA, LOCAL 1832, TERRITORIAL JURISDICTION AS FOLLOWS: COUNTIES OF DURHAM AND THAT PORTION OF ONTARIO NOT INCLUDED UNDER TORONTO LOCAL 1819 TERRITORIAL JURISDICTION.
PERFORMANCE MEASUREMENTS Upon a particular Commission’s issuance of an Order pertaining to Performance Measurements in a proceeding expressly applicable to all CLECs generally, BellSouth shall implement in that state such Performance Measurements as of the date specified by the Commission. Performance Measurements that have been Ordered in a particular state can currently be accessed via the internet at xxxx://xxxx.xxxxxxxxx.xxx. The following Service Quality Measurements (SQM) plan as it presently exists and as it may be modified in the future, is being included as the performance measurements currently in place for the state of Tennessee. At such time that the TRA issues a subsequent Order pertaining to Performance Measurements, such Performance Measurements shall supersede the SQM contained in the Agreement. BellSouth Service Quality Measurement Plan (SQM) Tennessee Performance Metrics Measurement Descriptions Version 2.00 Issue Date: July 1, 2003 Introduction
Corrective Measures If the Participating Generator fails to meet or maintain the requirements set forth in this Agreement and/or the CAISO Tariff, the CAISO shall be permitted to take any of the measures, contained or referenced in the CAISO Tariff, which the CAISO deems to be necessary to correct the situation.
AREA TO BE SERVED [SEE G.L.c. 166A §3(a)]
