Cooling mode definition

Cooling mode means an active mode in which a room air conditioner has activated the main cooling function according to the thermostat or temperature sensor signal or switch (including remote control).
Sample 1Sample 2Sample 3
Cooling mode. ’ means an active
Sample 1Sample 2Sample 3
Cooling mode means an active mode in which a portable air conditioner has activated the main cooling function according to the thermostat or temperature sensor signal, including activating the refrigeration system, or the fan or blower without activation of the refrigeration system.
Sample 1Sample 2

Examples of Cooling mode in a sentence

  • To remove the frost from the coil, the control initiates the defrost cycle when necessary (defrost mode acts as Cooling mode).

  • These tools can perform jobs like creating reports and therefore provide more time for professionals to focus on solving more complex problems, further enhancing efficiency.

  • The declaration is optional for AC2 multisplits, it will be tested only if declaredIf declared, the following performances must be tested:LRcontmin & CcpLRcontmin in Cooling mode and if relevant, in Heating mode.

  • Auto(2-Step Cooling or Heat)In Auto mode, the air conditioner will automatically set the temperature and fan speed depending on the room temperature detected by the room temperature sensor.• 2-Step Cooling mode sets the air conditioner to operate in Fast + Cool mode when set temperature is lower than indoor temperature, and then the air conditioner will automatically operate in Dry mode when indoor temperature reaches set temperature.

  • Start the heat pump, see Paragraph 5.2.4, press to select the operating mode:• Heating, is displayed, see Figure 13.• Cooling, is displayed, see Figure 14.Whenever the operating mode changes, the set temperature is switched to the following default values:• Heating mode, 40 [°C].• Cooling mode, 30 [°C].Thus, the set temperature must be regulated, see Paragraph 5.2.6, whenever the operating mode changes.

  • The initial lower limited value in the Cooling mode is 26℃ .When the Save function is activated, press Function to enter the Save setting interface and then press Enter/cancel to cancel this function.The Save setting for cooling is shown in the Fig.15 Fig.

  • Monitor and annunciate alarms for systems, conditions and equipment such as follows: • Fan failure (critical); • Heating mode out of nominal range (critical); • Cooling mode out of nominal range (critical); • Low space temperature (critical); • High space temperature (critical); • Run time accumulator reached; • Pump failure (critical).

  • Cooling mode tests for different types of air conditioners and heat pumps.

  • Cash used in operations for the quarter-ended June 30, 2015 resulted from a net loss, deferred income tax recovery and unrealized gain / loss on foreign exchange, which was offset by changes in non-cash working capital items, and by items not affecting cash such as amortization, interest accretion and stock-based compensation.

  • This is normal.Select Cooling ModeUse the mode button to select Cooling (instead of Heating).Programmed (AUTO) OperationFollow the steps in 7.1 (Operate the System in AUTO Mode), but at Step 7.1.b, select Cooling mode.Fan Only OperationFollow the steps in 9.1 (Fan Only Operation), but at Step 9.1.b, select Cooling mode.

Related to Cooling mode

  • Reliability pricing model or "RPM" means PJM's capacity-

  • Reliability Pricing Model Auction or “RPM Auction” shall mean the Base Residual Auction or any Incremental Auction, or, for the 2016/2017 and 2017/2018 Delivery Years, any Capacity Performance Transition Incremental Auction.

  • Cathode ray tube or “CRT” means a vacuum tube, composed primarily of glass, which is the visual or video display component of an electronic device. A “used, intact CRT” means a CRT whose vacuum has not been released. A “used, broken CRT” means glass removed from its housing or casing whose vacuum has been released.

  • Diameter means the diameter of the stem of a tree measured outside the bark at a specified point of measurement.

  • Diameter at breast height (dbh) means the diameter of a tree at 4 1/2 feet above the ground measured from the uphill side.

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Cubic Metre means the volume of gas which occupies one cubic metre when such gas is at a temperature of 15 degrees Celsius, and at a pressure of 101.325 kilopascals absolute;

  • Runway means a defined rectangular area on a land aerodrome prepared for the landing and take-off of aircraft;

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • Trench means 1. below-grade soil treatment area consisting of a shallow excavation with a width of 3 feet or less containing distribution media and one lateral; and 2. excavation for placement of piping or installation of electrical wire or conduit.

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Nameplate Capacity Rating means the maximum capacity of the Facility as stated by the manufacturer, expressed in kW, which shall not exceed 10,000 kW.

  • Ton means a ton of two thousand two hundred and forty (2,240) lbs. net dry weight;

  • Loop Concentrator/Multiplexer or "LCM" is the Network Element that does one or more of the following: aggregates lower bit rate or bandwidth signals to higher bit rate or bandwidth signals (multiplexing); disaggregates higher bit rate or bandwidth signals to lower bit rate or bandwidth signals (demultiplexing); aggregates a specified number of signals or channels to fewer channels (concentrating); performs signal conversion, including encoding of signals (e.g., analog to digital and digital to analog signal conversion); or in some instances performs electrical to optical (E/O) conversion. LCM includes DLC, and D4 channel banks and may be located in Remote Terminals or Central Offices.

  • Undercoating means any aerosol product designed to impart a protective, non-paint layer to the undercarriage, trunk interior, and/or firewall of motor vehicles to prevent the formation of rust or to deaden sound. “Undercoating” includes, but is not limited to, rubberized, mastic, or asphaltic products.

  • Vapor tight means equipment that allows no loss of vapors. Compliance with vapor-tight requirements can be determined by checking to ensure that the concentration at a potential leak source is not equal to or greater than 100 percent of the lower explosive limit (LEL) when measured with a combustible gas detector, calibrated with propane, at a distance of 1 inch (2.54 cm) from the source.

  • NACE means National Association of Corrosion Engineers

  • Adjusted Treasury Rate means, with respect to any Redemption Date, the rate per annum equal to the semi-annual equivalent yield to maturity of the Comparable Treasury Issue, assuming a price for the Comparable Treasury Issue (expressed as a percentage of its principal amount) equal to the Comparable Treasury Price for such Redemption Date.

  • Design-bid-build means a project delivery method in which:

  • Built-Up Area and/or “Covered Area” in relation to a Flat shall mean the floor area of that Flat including the area of balconies and terraces, if any attached thereto, and also the thickness of the walls (external or internal) and the columns and pillars therein Provided That if any wall, column or pillar be common between two Flats, then one-half of the area under such wall column or pillar shall be included in the built-up area of each such Flat.