Minimum length definition

Minimum length means the length of a fish measured in a straight line from the tip of the nose or jaw, whichever is longer, to the farthest tip of the tail fin when fully extended. When measuring turtles, it means the length of the dorsal surface of the carapace (top shell) measured from side to side across the shell at midpoint.
Minimum length means the smallest total length of a species or species group that may be legally possessed, measured from the tip of the snout to the end of the tail unless otherwise specified. No person shall possess any fish less than the lengths specified and any fish less than the minimum length shall, without avoidable injury, be immediately returned to the water from which taken.

Examples of Minimum length in a sentence

  • Minimum length of weld to be provided at various places in the stay sets shall be indicated by the bidder.

  • For dynamic bytes arrays (bytes), the minimum and maximum length may be specified using keyord arguments:• min_size: Minimum length for each returned value.

  • Minimum length blocks of four (4) feet six (6) inches may be poured only at the end of a day’s pour and then only with permission of the Engineer.303.2(d) Joints.

  • The minimum length of vertical curves necessary to provide adequate safe stopping sight distance shall be determined using the following formula:L = K AWhere:L = Minimum length of curve as measured in a horizontal plane.K = A measure of curvature, values of which are set forth in the following table.A = The algebraic difference between the grades of the tangents to the curve expressed in percent.

  • Minimum length, in feet, of these curves shall be twenty (20) times the algebraic difference in the percent of grade of the two adjacent slopes.

  • Minimum length blocks of four (4) feet six (6) inches may be poured only at the end of a day’s pour and then only with permission of the Engineer.

  • O.H. Ivie Reservoir (Coleman, Concho, and Runnels counties).(I) Daily bag limit: 5.(II) Minimum length limit: No limit.(III) It is unlawful to retain more than two bass of less than 18 inches in length.

  • Minimum Penetration Depth: Minimum length of pile below existing surface level or other specified surface level at pile location shown on the Design Documentation drawings.

  • H: Minimum height of shroud L: Minimum length of shroud W: Minimum width of shroudHWLShaded area represents screened open area.

  • L: Minimum length of shroud top opening W: Minimum width of shroud top opening H1: Minimum total height of shroudB: Minimum length of opening along base H2: Minimum height of opening along baseWLH1H2BShaded area represents screened open area.

Related to Minimum length

  • Minimum Level (ML means the concentration at which the entire analytical system must give a recognizable signal and an acceptable calibration point. The ML is the concentration in a sample that is equivalent to the concentration of the lowest calibration standard analyzed by a specific analytical procedure, assuming that all the method-specified sample weights, volumes and processing steps have been followed.

  • overall length means the distance between the two vertical planes perpendicular to the median longitudinal plane of the vehicle and touching its front and rear outer edge, disregarding the projection:

  • Minimum Threshold means the average daily yield on the 10 Year Treasury Note (as reported in the Bloomberg GT10 index) over the Award Period.

  • Minimum Transaction Size means the minimum value of subsequent subscriptions,

  • Minimum Acceptable Price with respect to any Put Notice Date shall mean seventy-five percent (75%) of the lowest closing bid prices for the ten (10) Trading Day period immediately preceding such Put Notice Date.

  • Minimum Term means, in respect of this Agreement, the period of 12 months beginning on the Effective Date;

  • Minimum Trade Price means the lowest Spot Price of the Units (subject to any adjustment to such Spot Price as may be necessary to reflect any event as contemplated in Product Condition 3 such as capitalisation, rights issue, distribution or the like) during the MCE Valuation Period;

  • Minimum Index Level means, in respect of a series of bull CBBCs, the lowest Spot Level of the Index during the MCE Valuation Period;

  • stipulated minimum threshold means that portion of local production and content as determined by the Department of Trade and Industry; and