We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Minimum thickness definition

Minimum thickness the thickness of the brake disc is the point at which replacement becomes necessary.

Examples of Minimum thickness in a sentence

  • Minimum thickness of 0.040 inch, with overlapping sleeves protecting threaded joints.

  • Minimum breakthrough time (glove): not determined Minimum thickness (glove): not determined Take note of the information given by the producer concerning permeability and break through times, and of specialworkplace conditions (mechanical strain, duration of contact).

  • Minimum thickness of 0.040 inch (1 mm), with overlapping sleeves protecting threaded joints.

  • Minimum thickness of base metal without coatings according to NAAMM-HMMA 803 or SDI A250.8.

  • Minimum thickness can vary according to materials, but must be at least four inches for Portland Cement Concrete (PCC) on four inches of graded aggregate base course (GABC).

  • Minimum thickness shall be 4-5mm or as specified in the Bill of Quantities.

  • Minimum thickness of anodic coating shall not be less than 25 µm.

  • Minimum thickness of base metal without coatings according to NAAMM-HMMA 803 or SDI A250.8. 1.4 COORDINATION A.

  • Minimum thickness: A = 2.0 mm- If the lining thickness is below the minimu- m, have the brake lining (1) replaced by a dealer.Checking the disc brake - Visually inspect the disc (2).

  • Minimum thickness: B = 3.0 mm- If the disc thickness is below the minimum,have the disc (2) replaced by a dealer.

Related to Minimum thickness

  • Minimum Term means the minimum initial period of service for each Service as shown on the Service Agreement and Order Schedule, such period to start on the date on which the relevant Service is first made available to you for use. For the avoidance of doubt, unless otherwise agreed the minimum term will be 12 months from your contract commencement date or other such date as may be notified to you in accordance with paragraph 19.2.

  • height means the vertical distance between grade and the highest point of the building or structure;

  • Nominal tomographic section thickness means the full width at half-maximum of the sensitivity profile taken at the center of the cross-sectional volume over which x-ray transmission data are collected.

  • Minimum Hire Period means the Minimum Hire Period as described on the invoices, quotation, authority to hire, or any other forms as provided by the Supplier to the Client.

  • Minimum Threshold means the average daily yield on the 10 Year Treasury Note (as reported in the Bloomberg GT10 index) over the Award Period.

  • Dusting aid means a product designed or labeled to assist in removing dust and other soils from floors and other surfaces without leaving a wax or silicone based coating. “Dusting Aid” does not include “Pressurized Gas Duster.”

  • Minimum Level (ML means the concentration at which the entire analytical system must give a recognizable signal and an acceptable calibration point. The ML is the concentration in a sample that is equivalent to the concentration of the lowest calibration standard analyzed by a specific analytical procedure, assuming that all the method-specified sample weights, volumes and processing steps have been followed.

  • Minimum Order Quantity means the minimum number of batches of a Product to be produced during the same cycle of manufacturing as set forth in a Product Agreement on Schedule B;

  • Barrier Level means the Barrier Level as specified in § 1 of the Product and Underlying Data.

  • Tare Weight means the weight of an empty shipping container, excluding all materials used for wrapping, cushioning, banding, waterproofing, packaging, blocking and bracing articles within the exterior container.

  • Minimum Annual Resource Requirement means, for Delivery Years through May 31, 2017, the minimum amount of capacity that PJM will seek to procure from Annual Resources for the PJM Region and for each Locational Deliverability Area for which the Office of the Interconnection is required under Tariff, Attachment DD, section 5.10(a) to establish a separate VRR Curve for such Delivery Year. For the PJM Region, the Minimum Annual Resource Requirement shall be equal to the RTO Reliability Requirement minus [the Sub-Annual Resource Reliability Target for the RTO in Unforced Capacity]. For an LDA, the Minimum Annual Resource Requirement shall be equal to the LDA Reliability Requirement minus [the LDA CETL] minus [the Sub-Annual Resource Reliability Target for such LDA in Unforced Capacity]. The LDA CETL may be adjusted pro rata for the amount of load served under the FRR Alternative.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which (1) a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and (2) while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.

  • Minimum Condition has the meaning set forth in Annex I.

  • Contract Specific Goals means the subcontracting goals for MBE and WBE participation established for a particular contract.

  • Minimum Balance Requirements The minimum balance to open the account is $5.00. If the balance falls below $5 at any time, the account may be closed. See Balance Computation Method above. Fees and Charges; Other Requirements: See our Schedule of Fees at xxxxxxx.xxx/xxxx. Dividends: See Disclosures Concerning Dividends above. Current rates are disclosed on the Credit Union’s website.

  • Yearly (1/Year) sampling frequency means the sampling shall be done in the month of September, unless specifically identified otherwise in the effluent limitations and monitoring requirements table.

  • Altitude means the vertical distance of a level, a point or an object considered as a point, measured from mean sea level (MSL);

  • Slash means all debris created on the Work area by the precommercial thinning operation.

  • Motor-driven cycle means every motorcycle that has a gasoline engine that (i) displaces less than

  • Adult theater means a theater, concert hall, auditorium, or similar commercial establishment which regularly features persons who appear in a state of nudity or live performances which are characterized by the exposure of "specified anatomical areas" or by "specified sexual activities."

  • Scale means the height, width and length of each building proposed within the development in relation to its surroundings;

  • Minimum DSCR means, with respect to a Supplemental Loan, (i) if the Senior Indebtedness bears interest at a fixed rate, 1.25:1, or (ii) if the Senior Indebtedness bears interest at a floating rate, 1.10:1.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • Uptime means the time period when specified services are available with specified technical and service standards as mentioned in section titled WARRANTY SUPPORT” "%Uptime" means ratio of 'up time' (in minutes) as mentioned in section titled “Warranty support”

  • Penetration Testing means security testing in which assessors mimic real-world attacks to identify methods for circumventing the security features of an application, system, or network. (NIST SP 800-115)