Reduced pressure backflow assembly definition

Reduced pressure backflow assembly. (RPBA) means a type of
Reduced pressure backflow assembly. (RPBA) means an approved assembly consisting of two independently operating check valves, spring loaded to the closed position, separated by a spring loaded differential pressure relief valve loaded to the open position, an installed as a unit with and between two resilient seated shutoff valves and having suitable connections for testing. The assembly must operate to maintain the pressure in the zone between the two check valves, less than the pressure on the public water system side of the device. At cessation of normal flow, the pressure between the check valve must be less than the supply pressure. In case of leakage of either check valve, the differential relief valve must operate to maintain the reduced pressure by discharging to the atmosphere. When the inlet pressure drops below two (2) pounds per square inch (13.8 kPa) the relief valve must open to the atmosphere thereby providing an atmospheric zone between the two check valves. (Ord. 1349 §1(part), 2003: Ord. 1190 §3(part), 1996).
Reduced pressure backflow assembly. (RPBA) means an assembly incorporating two check valves and an automatically operating differential relief valve, located between the two shutoff valves, and equipped with necessary appurtenances for testing. This assembly may be used for non-health and health-hazard applications.

Examples of Reduced pressure backflow assembly in a sentence

  • UPON RECEIVING APPROPRIATE FEE PAYMENTS AND VERIFYING THAT REDUCED PRESSURE BACKFLOW ASSEMBLY (RPBA) HAS BEEN INSTALLED (NOT BY CITY), THE CITY WILL INSTALL THE DOMESTIC METER INSIDE THE DOMESTIC METER BOX.

  • As noted in the EJR request and in the regulatory history cited above, the Secretary adopted its policy of including no-pay Part A days in the Medicare fraction policy in the FY 2005 IPPS Final Rule.

  • W4-29 REDUCED PRESSURE BACKFLOW ASSEMBLY All Reduced Pressure Backflow Assemblies shall be as listed on the most current copy of "Backflow Prevention Assemblies Approved for Installation in Washington State", published by Washington State Department of Health (D.O.H.).

  • ELL)-students identified by the State Board of Education (State Board) as not proficient in the English language based upon approved English proficiency assessment instruments administered annually in the fall of the current school year, which assessments measure oral, reading, and writing proficiency.

  • REDUCED PRESSURE BACKFLOW ASSEMBLY (RPBA)  Requires annual testing by a certified tester. High hazard systems. Allows for application of fertilizer or other chemicals into irrigation system.


More Definitions of Reduced pressure backflow assembly

Reduced pressure backflow assembly. (RPBA) means an approved assembly consisting of two independently operating check valves, spring loaded to the closed position, separated by a spring loaded differential pressure relief valve loaded to the open position, and installed as a unit with and between two resilient seated shutoff valves and having four suitable test cocks for checking the water tightness of the check valves and the operation of the relief valve.
Reduced pressure backflow assembly means an approved assembly containing two independently acting approved check valves together with a hydraulically-operatedhydraulically operated, mechanically independent pressured differential relief valve located between the check valves and at the same time below the first check valve. The assembly shall include properly located test cocks and tightly resilient seated shut-off valves at the ends of the assembly, and unions at the ends of the assembly.

Related to Reduced pressure backflow assembly

  • Bulk gasoline plant means a gasoline storage and distribution facility with an average daily throughput of 20,000 gallons (76,000 liters) of gasoline or less on a 30-day rolling average.

  • low voltage means the set of nominal voltage levels that are used for the distribution of electricity and whose upper limit is generally accepted to be an a.c. voltage of 1000V ( or a d.c. voltage of 1500 V). [SANS 1019]

  • Generator Forced Outage means an immediate reduction in output or capacity or removal from service, in whole or in part, of a generating unit by reason of an Emergency or threatened Emergency, unanticipated failure, or other cause beyond the control of the owner or operator of the facility, as specified in the relevant portions of the PJM Manuals. A reduction in output or removal from service of a generating unit in response to changes in market conditions shall not constitute a Generator Forced Outage.

  • Combustion turbine means an enclosed fossil or other fuel-fired device that is comprised of a compressor, a combustor, and a turbine, and in which the flue gas resulting from the combustion of fuel in the combustor passes through the turbine, rotating the turbine.

  • generating plant means the generating facility described in Schedule 1 as amended from time to time;

  • Backflow prevention device means a safety device used to prevent pollution or contamination of the water supply due to the reverse flow of water from the irrigation system.

  • Operational Acceptance Tests means the tests specified in the Technical Requirements and Agreed Project Plan to be carried out to ascertain whether the System, or a specified Sub system, is able to attain the functional and performance requirements specified in the Technical Requirements and Agreed Project Plan, in accordance with the provisions of GCC Clause 27.2 (Operational Acceptance Test).

  • Interconnector means equipment used to link the electricity system of the State to electricity systems outside of the State;

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Output means the exposure rate, dose rate, or a quantity related in a known manner to these rates from a brachytherapy source or a teletherapy, remote afterloader, or gamma stereotactic radiosurgery unit for a specified set of exposure conditions.

  • True vapor pressure means the equilibrium partial pressure exerted by a petroleum liquid as determined in accordance with methods described in American Petroleum Institute (API) Bulletin 2517, Evaporation Loss from External Floating Roof Tanks, 1980. The API procedure may not be applicable to some high viscosity or high pour crudes. Available estimates of true vapor pressure may be used in special cases such as these.

  • Generation Interconnection Feasibility Study means a study conducted by the Transmission Provider (in coordination with the affected Transmission Owner(s)) in accordance with Tariff, Part IV, section 36.2.

  • Gasification means the substoichiometric oxidation or steam reformation of a substance to produce a gaseous mixture containing two or more of the following: (i) oxides of carbon; (ii) methane; and (iii) hydrogen;

  • Outputs means the goods or services that are produced by an entity or other person;

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Backflow preventer means any device or means to prevent backflow;

  • Reid vapor pressure means the vapor pressure of crude oil or other volatile petroleum products at 100 degrees Fahrenheit as determined by the latest edition of ASTM D6377 (RVPE): Standard Test Method for Determination of Vapor Pressure of Crude Oil.

  • Attachment point means a point on the network at which network assets are connected to assets owned by another person.

  • Generator Planned Outage means the scheduled removal from service, in whole or in part, of a generating unit for inspection, maintenance or repair with the approval of the Office of the Interconnection in accordance with the PJM Manuals.

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV < Un 44 kV. [SANS 1019]

  • Operating pressure means the pressure at which the parts of an irrigation system are designed by the manufacturer to operate.