Roof assembly definition

Roof assembly means all components of the roof and ceiling envelope through which heat flows, thus creating a building transmission heat loss or gain, where such assembly is exposed to outdoor air and encloses a heated space. Any skylight shaft walls less than 12 inches in depth, as measured from the ceiling plane to the roof deck, are considered in the roof assembly and are not considered in the area of exterior walls.
Sample 1Sample 2
Roof assembly. (NRS 482.106) means the structural parts of a vehicle, including, without limitation, more than one- half of the vertical roof supports, the framework of the roof and the exterior metal skin that together are designed and intended to be located over the passenger compartment to form the roof of the vehicle.
Sample 1
Roof assembly means a building cover and its supporting structure including any ceiling attached to such structure;
Sample 1

Examples of Roof assembly in a sentence

  • The definition of "Roof assembly" is limited in application to the provisions of Chapter 15.

  • C402.2.1 Roof assembly The minimum thermal resistance (R-value) of the insulating material installed either between the roof framing or continuously on the roof assembly shall be as specified in Table C402.1.3, based on construction materials used in the roof assembly.

  • Factory Mutual Research (FM), wind uplift resistance classification: Roof assembly shall be classified as FM 1-90, as defined by FM 4470.

  • In order to reduce the U- value of the Roof assembly to 0.4 W/m2C, roof tiles with surki backing shall be laid on roof to minimize heat transfer from the roof.

  • DOE’s Office of Environmental Restoration (EM-40) (contact: Mary McCune, EM-22) has developed a set of PAMs that identify commercially available environmental restoration tech- nologies and rank them on the basis of performance, risk of technology failure, and cost.

  • They are: (a) Under Body Complete (UBC) line– consists of Dash, Engine Box, Ladder, Floor sub assemblies, (b) Body Side Aperture (BSA) complete line – consists of BSA inner sub assembly, BSA outer sub- assembly, (c) Body Framing line – consists of Toy-tab, Body framing and Respot, (d) Roof assembly line, and (e) the installation of hang on panels- consists of fenders, doors, hood and trunk or lift gate sub-assemblies.The BIW assembly processes flow is shown in Figure: 1.Figure: 1.

  • Roof assembly unit Roof assembly was carried out by four teams of four people.

  • Exterior wall architectural trim, embellishments, fascias, and gutters.2. Roof or wall top cornice projections and similar assemblies.3. Roof assembly projections over gable end walls..4.

  • FMRC - Approval Guide - Roof Coverings and/or Roof assembly database.

  • Roof assembly shall achieve an R-30 value in accordance with 24 CFR 3280.506.


More Definitions of Roof assembly

Roof assembly means a building cover and its supporting structure includ- ing any ceiling attached to such structure;
Sample 1

Related to Roof assembly

  • Assembly means the Assembly of Heads of State and Government of the African Union;

  • Digital audio-visual work means a series of related images which, when shown in succession, imparts an impression of motion, together with accompanying sounds, if any.

  • Installation Works means, as the context so requires,

  • Installation Work means the construction and installation of the System and the Start-up, testing and acceptance (but not the operation and maintenance) thereof; all performed by or for the Power Producer at the Premises.

  • Installation means that the System or a Subsystem as specified in the Contract is ready for Commissioning as provided in GCC Clause 26 (Installation).

  • audiovisual work means a work that consists of a series of related images which impart the impression of motion, with or without accompanying sounds, susceptible of being made visible and, where accompanied by sounds, susceptible of being made audible;

  • Telecommunications Equipment means equipment, other than Customer Premises Equipment, used by a Carrier to provide Telecommunications Services, and include software integral to such equipment, including upgrades.

  • Installation Site means the site at which the Product is originally installed.

  • Fabrication means making up data or results and recording or reporting them.

  • Retrofit means to alter, improve, modify, remodel or renovate a building, facility or structure to make that building, facility or structure more energy-efficient.

  • the Assembly means the National Assembly for Wales;

  • Web spray adhesive means any aerosol adhesive that is not a mist spray or special purpose spray adhesive.

  • Installation Services means all those services ancillary to the supply of the Plant and Equipment for the Facilities, to be provided by the Contractor under the Contract; e.g., transportation and provision of marine or other similar insurance, inspection, expediting, site preparation works (including the provision and use of Contractor’s Equipment and the supply of all construction materials required), installation, testing, pre-commissioning, commissioning, operations, maintenance, the provision of operations and maintenance manuals, training, etc.

  • Communications Equipment means the communications equipment of the Licensee and its affiliates, including, without limitation, cabinets, racks, electronic equipment and other similar equipment.

  • Membrane filtration means a pressure or vacuum driven separation process in which particulate matter larger than one micrometer is rejected by an engineered barrier, primarily through a size exclusion mechanism, and which has a measurable removal efficiency of a target organism that can be verified through the application of a direct integrity test. This definition includes the common membrane technologies of microfiltration, ultrafiltration, nanofiltration, and reverse osmosis.

  • Display fireworks means large fireworks devices that are explosive materials intended for use in fireworks displays and designed to produce visible or audible effects by combustion, deflagration, or detonation, as provided in 27 CFR 555.11, 49 CFR 172, and APA standard 87-1, 4.1.

  • Diagnostic source assembly means the tube housing assembly with a beam-limiting device attached.

  • Installation Date means the date specified in the Statement of Work by which the Contractor must have the ordered Equipment ready (certified) for use by the State.

  • Remanufacturing means the activity of overhauling, retrofitting, fabricating, or repairing a product or its component parts for ultimate sale at retail.

  • Tube housing assembly means the tube housing with tube installed. It includes high-voltage and/or filament transformers and other appropriate elements when such are contained within the tube housing.

  • Fireworks means display fireworks, pyrotechnic special effects fireworks and consumer fireworks;

  • Semiconductor equipment means (i) machinery or tools or repair parts or replacements thereof; (ii)

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Digital audio works which means works that result from the fixation of a series of musical, spoken, or other sounds, including ringtones; and

  • Cabinet x-ray system means an x-ray system with the x-ray tube installed in an enclosure independent of existing architectural structures except the floor on which it may be placed. The cabinet x-ray system is intended to contain at least that portion of a material being irradiated, provide radiation attenuation, and exclude personnel from its interior during generation of radiation. Included are all x-ray systems designed primarily for the inspection of carry-on baggage at airline, railroad, and bus terminals, and in similar facilities. An x-ray tube used within a shielded part of a building, or x-ray equipment that may temporarily or occasionally incorporate portable shielding, is not considered a cabinet x-ray system.

  • Transformation time means the time difference between a change of concentration or flow (t0) at the reference point and a system response of 50 per cent of the final reading (t50).