Static test definition

Static test means the test during which lifting machinery or a lifting accessory is first inspected and subjected to a force corresponding to the maximum working load multiplied by the appropriate static test coefficient and then re-inspected once the said load has been released to ensure that no damage has occurred.
Sample 1Sample 2Sample 3
Static test means a test which complies with the requirements of paragraph 3(5) and which applies the forces specified in paragraph 3(6);
Sample 1Sample 2Sample 3
Static test means a test carried out to determine the compliance of the brake holding power of a trackless mobile machine measured against the design specification or an appropriate safety standard;
Sample 1Sample 2

Examples of Static test in a sentence

  • POWER: Static test a specific attribute to grant a larger bonus on a single test, if the power is very powerful you may want to have a consequence for failure.Example: Flaming Sword: Static Test Health.

  • Static test; see Table D2A, Flight Train- ing Device (FTD) Objective Tests, Entries 2.a.1., 2.a.2., and 2.a.3.

  • Toxicity to fish: Static test LC50, Pimephales promelas, 577 mg/l, 96 hours.Toxicity to daphnia: Static test LC50, Daphnia magna, 206.8 mg/l, 48 hours and other aquatic invertebrates.

  • Tolerances(a) Static test, see paragraph (b)(3) – 2.a(1), (2), and (3) of the table of FSTD validation tests.(b) Dynamic test – ± 0.9 daN (2 lbs) or ± 10% on dynamic increment above static test.The competent authority is open to alternative means such as the one described above.

  • Tolerances(a) Static test: see (b)(3) – 2.a(1), (2), and (3) of table of FSTD validation tests.(b) Dynamic test: ± 0.9 daN (2 lbs) or ± 10% on dynamic increment above static test.The competent authority should consider alternative means such as the one described above.

  • These tests should be conducted at typical flight and ground conditions.(a) Static test – slowly move the control such that approximately 100 s are required to achieve a full sweep.

  • The same as the monthly maintenance.b. Testing the battery capacity.c. Static test procedure.

  • Static test pressure(horizontal)(kg/cm2): 23.76 (COIL SIDE) Weight (erection) Kg. : 12,000(approx.) Height : 8.8 meter ID of Shell : 1.855 meter length of exhaust pipe : 6.0 meter Material of construction : Valves/instruments : data sheet available Fitting-socket weld : SA 105 ANSI B 16.11 Fitting-Butt weld: SA 234 Gr WPB ANSI B 16.9 Fastener-Bolt/Nut: SA 193 Gr B7/194 Grade 2H ELECTRO-GALVANIZED Gasket - SP.

  • Static test report or static load calculation stamped by Grade A registered National structural engineer, in duplicate; 3.

  • These tests should be conducted at typical flight and ground conditions.(a) Static test – slowly move the control such that approximately100 s are required to achieve a full sweep.


More Definitions of Static test

Static test means a test which complies with the requirements of paragraph
Sample 1
Static test means the test during which lifting machinery or a lifting accessory is first inspected and subjected to a force corresponding to the maximum working load multiplied by the appropriate static
Sample 1
Static test means the test during which lifting machinery or a lifting accessory is first inspected and subjected to a force corresponding to the maximum working load
Sample 1
Static test means the test carried out to determine the compliance of the brake holding power of a locomotive braking system measured against the design specification or an appropriate safety standard;
Sample 1

Related to Static test

  • RDDS test Means one query sent to a particular “IP address” of one of the servers of one of the RDDS services. Queries shall be about existing objects in the Registry System and the responses must contain the corresponding information otherwise the query will be considered unanswered. Queries with an RTT 5 times higher than the corresponding SLR will be considered as unanswered. The possible results to an RDDS test are: a number in milliseconds corresponding to the RTT or undefined/unanswered.

  • EPP test Means one EPP command sent to a particular “IP address” for one of the EPP servers. Query and transform commands, with the exception of “create”, shall be about existing objects in the Registry System. The response shall include appropriate data from the Registry System. The possible results to an EPP test are: a number in milliseconds corresponding to the “EPP command RTT” or undefined/unanswered.

  • DNS test Means one non-­‐recursive DNS query sent to a particular “IP address” (via UDP or TCP). If DNSSEC is offered in the queried DNS zone, for a query to be considered answered, the signatures must be positively verified against a corresponding DS record published in the parent zone or, if the parent is not signed, against a statically configured Trust Anchor. The answer to the query must contain the corresponding information from the Registry System, otherwise the query will be considered unanswered. A query with a “DNS resolution RTT” 5 times higher than the corresponding SLR, will be considered unanswered. The possible results to a DNS test are: a number in milliseconds corresponding to the “DNS resolution RTT” or, undefined/unanswered.

  • Genetic testing means an analysis of genetic markers to exclude or identify a man as the father or a woman as the mother of a child. The term includes an analysis of one or a combination of the following:

  • COVID-19 test means a viral test for SARS-CoV-2 that is:

  • Fit test means the use of a protocol to qualitatively or quantitatively evaluate the fit of a respirator on an individual.

  • Screening Test means a drug or alcohol test which uses a method of analysis allowed by the Minnesota Drug and Alcohol Testing in the Workplace Act to be used for such purposes.

  • Penetration Testing means security testing in which assessors mimic real-world attacks to identify methods for circumventing the security features of an application, system, or network. (NIST SP 800-115)

  • stratigraphic test well means a drilling effort, geologically directed, to obtain information pertaining to a specific geologic condition. Ordinarily, such wells are drilled without the intention of being completed for hydrocarbon production. They include wells for the purpose of core tests and all types of expendable holes related to hydrocarbon exploration. Stratigraphic test wells are classified as (i) "exploratory type" if not drilled into a proved property; or (ii) "development type", if drilled into a proved property. Development type stratigraphic wells are also referred to as "evaluation wells".

  • Drug test means a test designed to detect the illegal use of a controlled substance.

  • Performance Test means all operational checks and tests required to determine the performance parameters including inter-alia capacity, efficiency and operating characteristics of the Stores as specified in the Contract.

  • Percolation test means a subsurface soil test at the depth of a proposed absorption system or similar component of an OWTS to determine the water absorption capability of the soil, the results of which are normally expressed as the rate at which one inch of water is absorbed. The rate is expressed in minutes per inch.

  • Coverage Test means each of the Class A/B Par Value Test, the Class A/B Interest Coverage Test, the Class C Par Value Test, the Class C Interest Coverage Test, the Class D Par Value Test, the Class D Interest Coverage Test, the Class E Par Value Test and the Class E Interest Coverage Test.

  • Critical Test Concentration or "(CTC)" means the specified effluent dilution at which the Permittee is to conduct a single-concentration Aquatic Toxicity Test.

  • Acceptance Test is a test of the Features executed by the Customer to prepare the acceptance.

  • Drug use test means a scientifically substantiated method to test for the presence of illegal or performance-enhancing drugs or the metabolites thereof in a person’s urine.

  • Cannabis testing facility means an entity registered by

  • Collateral Quality Tests means the Collateral Quality Tests set out in the Investment Management Agreement being each of the following:

  • Instantaneous flow measurement means the flow measured during the minimum time required for the flow-measuring device or method to produce a result in that instance. To the extent practical, instantaneous flow measurements coincide with the collection of any grab samples required for the same sampling period so that together the samples and flow are representative of the discharge during that sampling period.

  • Confirmation test means a drug or alcohol test on a sample to substantiate the results of a prior drug or alcohol test on the same sample and which uses different chemical principles and is of equal or greater accuracy than the prior drug or alcohol test;