Test voltage definition

Test voltage. Voltage, at the input terminals of the ballast for which the electrical and photometric characteristics of the gas- discharge light source are intended and are to be tested.
Test voltage. 1500 vdc Trip Current: <= 5 mA Voltage Ramp: 1500 vdc/ 100 msec maximum Test Time: 1 second. Ground Continuity Criteria: Test circuit: 25 Amps AC Trip Resistance: 0.1 ohm Test Time: 6 second. Adept / Samsung Page 33 Motor Resistance Check - Validate proper system resistance and connection. Connect to Controller System - Confirm controller configuration and connections. [GRAPHIC] BRING-UP - This series of operations sets model specific and unit specific information about the robot. Such information will be stored offline or in the Robot Signature Card, (RSC), if this component is included in the robot system design. Each process step is automated using Adept test software (Autotest). Process steps, data collection and test results are maintained by software and stored to disc.
Test voltage means voltage at the filament lamp terminals for which the electrical and photometric characteristics of the filament lamp are intended and are to be tested. In case of gas-discharge light source, voltage at the input terminals of the ballast.

Examples of Test voltage in a sentence

  • Test voltage shall be in accordance with manufacturer’s published data.

  • Test voltage shall be recorded when measured RIV passes through 100 microvolts in each direction.

  • Test voltage and amperage on all condenser fan motors and evaporator fan motors.- Inspect conditions of condenser fan and evaporator fan blades.4. Check for proper air flow on condenser fans and evaporator fans.5. Check proper operation of any outside, supply and return air dampers.6. Clean and flush all condensation pans and drain lines.7. Check all electrical components and connections to include safety controls.- Safety controls are strictly prohibited from being bypassed.

  • Test voltage should be in accordance with manufacturer’s published data.

  • Test coupons shall be provided per the specification for each shipment.MSQ-30 Printed Wiring Board TestingGuidance: A and B apply when MSQ-30 is required.A. Unless otherwise specified in Engineering Requirements Documentation, Seller shall perform bare board testing with these values: Test voltage -10-250V, continuity -10 ohm maximum, insulation resistance -10K ohm minimum.

  • If, during the Performance Test, voltage tests cannot be performed due to Grid System, data supplied from tests of the generator step-up transformers and generators supplied by the manufacturers shall be used to establish the ability of the Unit to operate within the specified voltage limits.

  • Unless otherwise specified in Engineering Requirements Documentation, Seller shall perform bare board testing with these values: Test voltage -10-250V, continuity -10 ohm maximum, insulation resistance -10K ohm minimum.

  • Test voltage shall be in accordance with manufacturer’s published data or 500 Vdc.

  • Test voltage on each conductor to verify that it is de-energized.

  • Test voltage shall be in accordance with manufacturer's published data.


More Definitions of Test voltage

Test voltage means the voltage, at the input terminals of the light source or at the terminals of the ballast for the gas-discharge light source, for which the electrical and photometric characteristics of the light source are intended and are to be tested.

Related to Test voltage

  • low voltage means the set of nominal voltage levels that are used for the distribution of electricity and whose upper limit is generally accepted to be an a.c. voltage of 1000V ( or a d.c. voltage of 1500 V). [SANS 1019]

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV to 44 kV;

  • voltage means the root-mean-square value of electrical potential between two conductors.

  • high voltage means the classification of an electric component or circuit, if its working voltage is > 60 V and ≤ 1500 V DC or > 30 V and ≤ 1000 V AC root mean square (rms).

  • High voltage bus means the electrical circuit, including the coupling system for charging the REESS that operates on a high voltage.

  • Rated Voltage means the manufacturer’s design voltage at which the transmission system is designed to operate or such lower voltage at which the line is charged, for the time being, in consultation with Transmission System Users;

  • Working voltage means the highest value of an electrical circuit voltage root-mean-square (rms), specified by the manufacturer, which may occur between any conductive parts in open circuit conditions or under normal operating conditions. If the electrical circuit is divided by galvanic isolation, the working voltage is defined for each divided circuit, respectively.

  • Output means the exposure rate, dose rate, or a quantity related in a known manner to these rates from a brachytherapy source or a teletherapy, remote afterloader, or gamma stereotactic radiosurgery unit for a specified set of exposure conditions.

  • generating plant means the generating facility described in Schedule 1 as amended from time to time;

  • Small quantity generator means a generator who generates less than 1000 kg of hazardous waste in a calendar month.

  • Outputs means the goods or services that are produced by an entity or other person;

  • INTER-CONNECTION POINT/ DELIVERY/ METERING POINT means a single point at 220kV or above, where the power from the Project(s) is injected into the identified ISTS Substation (including the dedicated transmission line connecting the Projects with the substation system) as specified in the RfS document. Metering shall be done at this interconnection point where the power is injected into. For interconnection with grid and metering, the WPDs shall abide by the relevant CERC/ SERC Regulations, Grid Code and Central Electricity Authority (Installation and Operation of Meters) Regulations, 2006 as amended and revised from time to time.

  • Sewage sludge weight means the weight of sewage sludge, in dry U.S. tons, including admixtures such as liming materials or bulking agents. Monitoring frequencies for sewage sludge parameters are based on the reported sludge weight generated in a calendar year (use the most recent calendar year data when the NPDES permit is up for renewal).

  • Backpressure means a pressure (caused by a pump, elevated tank or piping, boiler, or other means) on the consumer's side of the service connection that is greater than the pressure provided by the public water system and which may cause backflow.

  • Load means energy consumed by Customers together with allocated losses and unaccounted for energy;

  • heat pump means a machine, a device or installation that transfers heat from natural surroundings such as air, water or ground to buildings or industrial applications by reversing the natural flow of heat such that it flows from a lower to a higher temperature. For reversible heat pumps, it may also move heat from the building to the natural surroundings;

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Tank means an enclosed space which is formed by the permanent structure of a ship and which is designed for the carriage of liquid in bulk.

  • Net Metering Net metering refers to customers who sell electricity they produce, typically through a rooftop solar panel, back to the utility for credit. If you are a net metering customer, you should not enroll with XOOM because your net metering agreement will not transfer to XOOM once you enroll.

  • Net metering system means a facility for the production of electrical energy that does all of the following:

  • Biomass means the biodegradable fraction of products, waste and residues from biological origin from agriculture (including vegetal and animal substances), forestry and related industries including fisheries and aquaculture, as well as the biodegradable fraction of industrial and municipal waste;

  • Diameter at breast height (dbh) means the diameter of a tree at 4 1/2 feet above the ground measured from the uphill side.

  • Bulk mixing plant means machinery, appliances or other similar devices that are assembled in such a manner so as to be able to mix materials in bulk for the purposes of using the mixed product for construction work;

  • Generator Forced Outage means an immediate reduction in output or capacity or removal from service, in whole or in part, of a generating unit by reason of an Emergency or threatened Emergency, unanticipated failure, or other cause beyond the control of the owner or operator of the facility, as specified in the relevant portions of the PJM Manuals. A reduction in output or removal from service of a generating unit in response to changes in market conditions shall not constitute a Generator Forced Outage.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.