Common use of Acceptance conditions Clause in Contracts

Acceptance conditions. The access probe shall not touch live parts. If this requirement is verified by a signal circuit between the probe and live parts, the lamp shall not light. In the case of the test for IPXXB, the jointed test finger may penetrate to its 80 mm length, but the stop face (diameter 50 mm x 20 mm) shall not pass through the opening. Starting from the straight position, both joints of the test finger shall be successively bent through an angle of up to 90 degrees with respect to the axis of the adjoining section of the finger and shall be placed in every possible position. In case of the tests for IPXXD, the access probe may penetrate to its full length, but the stop face shall not fully penetrate through the opening. Table 1 Comment Public Figure 1 nly Comment Public Material: metal, except where otherwise specified Linear dimensions in millimeters Tolerances on dimensions without specific tolerance: (a) On angles: 0/-10°; (b) On linear dimensions: up to 25 mm: 0/-0.05 mm over 25 mm: ±0.2 mm Both joints shall permit movement in the same plane and the same direction through an angle of 90° with a 0 to +10° tolerance.

Acceptance conditions. The access probe shall not touch live parts. If this requirement is verified by a signal circuit between the probe and live parts, the lamp shall not light. In the case of the test for IPXXB, the jointed test finger may penetrate to its 80 mm length, but the stop face (diameter 50 mm x 20 mm) shall not pass through the opening. Starting from the straight position, both joints of the test finger shall be successively bent through an angle of up to 90 degrees with respect to the axis of the adjoining section of the finger and shall be placed in every possible position. In case of the tests for IPXXD, the access probe may penetrate to its full length, but the stop face shall not fully penetrate through the opening. Table 1 Comment Public Figure 1 nly Comment Public R4 = 0.05 spherical R2 ± 0.05 Material: metal, except where otherwise specified Linear dimensions in millimeters Tolerances on dimensions without specific tolerance: (a) On angles: 0/-10°; (b) On linear dimensions: up to 25 mm: 0/-0.05 mm over 25 mm: ±0.2 mm Both joints shall permit movement in the same plane and the same direction through an angle of 90° with a 0 to +10° tolerance.

Acceptance conditions. The access probe shall not touch live parts. If this requirement is verified by a signal circuit between the probe and live parts, the lamp shall not light. In the case of the test for IPXXB, the jointed test finger may penetrate to its 80 mm length, but the stop face (diameter 50 mm x 20 mm) shall not pass through the opening. Starting from the straight position, both joints of the test finger shall be successively bent through an angle of up to 90 degrees with respect to the axis of the adjoining section of the finger and shall be placed in every possible position. In case of the tests for IPXXD, the access probe may penetrate to its full length, but the stop face shall not fully penetrate through the opening. Table 1 Comment Public Figure 1 nly Comment Public Material: metal, except where otherwise specified Linear dimensions in millimeters Tolerances on dimensions without specific tolerance: (a) On angles: 0/-10°; (b) On linear dimensions: up to 25 mm: 0/-0.05 mm over 25 mm: ±0.2 mm Both joints shall permit movement in the same plane and the same direction through an angle of 90° with a 0 to +10° tolerance.

Acceptance conditions. The access probe shall not touch live parts. If this requirement is verified by a signal circuit between the probe and live parts, the lamp shall not light. In the case of the test for IPXXB, the jointed test finger may penetrate to its 80 mm length, but the stop face (diameter 50 mm x 20 mm) shall not pass through the opening. Starting from the straight position, both joints of the test finger shall be successively bent through an angle of up to 90 degrees with respect to the axis of the adjoining section of the finger and shall be placed in every possible position. In case of the tests for IPXXD, the access probe may penetrate to its full length, but the stop face shall not fully penetrate through the opening. Table 1 Comment Public Figure 1 nly Comment Public Material: metal, except where otherwise specified Linear dimensions in millimeters Tolerances on dimensions without specific tolerance: (a) On Nn angles: 0/-10°; (b) On linear dimensions: up to 25 mm: 0/-0.05 mm over 25 mm: ±0.2 mm Both joints shall permit movement in the same plane and the same direction through an angle of 90° with a 0 to +10° tolerance.