Appropriate Methods i. Specific teaching methods, student learning activities, and assessment methods used and the procedures/steps followed to achieve the FLO
Appropriate Methods Sample Clauses
Related to Appropriate Methods
Selection Criteria Each Contract is secured by a new or used Motorcycle. No Contract has a Contract Rate less than 1.00%. Each Contract amortizes the amount financed over an original term no greater than 84 months (excluding periods of deferral of first payment). Each Contract has a Principal Balance of at least $500.00 as of the Cutoff Date.
Construction Methods 3.1 The Contractor shall provide all tools, equipment, materials, labor and work for the excavation and removal of the unsuitable subgrade soils and their subsequent replacement with the specified backfill soils as directed by the Owner’s representative. All work under this item shall be performed in a safe and workmanlike manner. 3.2 All work shall be performed in accordance with DelDOT Standard Specifications Section 821. 3.3 Following the removal of existing pavements, the Owner’s representative will review the exposed subgrade and provide recommendations for the undercutting of unsuitable subgrade materials as required. The depth and extent of undercut excavation, if required, will be determined by the Owner’s representative at the time of excavation. 3.4 All excavated materials shall become the property of the Contractor and be removed from the site at the completion of the project at no additional expense to the Owner. 3.5 Undercut excavations should be backfilled with graded aggregate. Backfill shall be placed in loose lifts not exceeding 8 inches thick. Each lift should be compacted with at least 3 passes of a minimum 5-ton, walk-behind or self-propelled vibratory roller when the size of the area permits, or with a vibrating plate mechanical compactor for smaller areas. Lift thickness shall be reduced to 6 inch loose lift when using a vibratory plate compactor. 3.6 The Contractor shall take precautions as necessary to minimize the potential for disturbance or softening of the pavement subgrade materials from inclement weather or construction traffic. As a minimum, this shall include the placement of backfill on the same day as the excavation. Any soft areas which develop shall be undercut and replaced with graded aggregate at no additional cost to the Owner. 3.7 Where undercutting is performed, the geotextile fabric shall be installed. The fabric should be pulled tight and lapped a minimum of 12 inches.
Transfer Methods and Amounts Section 15 of the General Terms (Payment Methods and Amounts) applies to the Service, even in circumstances where the External Account is closed and we are attempting to return funds to such Account.
Payment Methods A. Except as otherwise provided by this Contract, the payment method will be one or more of the following:
Accounting Methods Implement or adopt any change in its accounting principles, practices or methods, other than as may be required by generally accepted accounting principles.
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C. 1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
BRAND NAME OR EQUALS/DEVIATIONS Unless otherwise specified, the mention of a particular manufacturer’s brand name or number in the specifications does not imply that this particular good is the only one that will be considered for purchase. This reference is intended solely to designate the type or quality of good that will be acceptable. Equal offers will be considered and must include descriptive literature and/or specifications. Failure to provide descriptive literature and/or specifications with equal offers will result in the disqualification of the bid. The determination as to whether any alternate good or service is or is not equal shall be made solely by the County and such determination shall be final and binding upon all bidders. The County reserves the right to request and review additional information to make such a determination. Although the County provides for the consideration of alternate bids, it reserves the right to make an award in the best interest of the County. Award may not necessarily be given to the lowest bid offered. The Bidder shall be responsible for reading very carefully, and understanding completely, the requirements and the specifications of the items bid upon. Unless the bid is in response to a “Brand Name or Equal” requirement, deviations from the specifications will only be considered if requested in writing prior to the date and time specified for receipt of bids. Deviations, if accepted, will be specifically addressed in writing via an addendum to this Invitation for Bids. Any goods or services that are not in compliance with the specifications will not be accepted.
Time and Method of Payment (Amounts Distributed by the Administrative Agent). Except as otherwise provided in Section 4.02, all amounts payable to any Funding Agent or Investor hereunder or with respect to the Series 2019-1 Class A-1 Advance Notes shall be made to the Administrative Agent for the benefit of the applicable Person, by wire transfer of immediately available funds in Dollars not later than 3:00 p.m. (Eastern time) on the date due. The Administrative Agent will promptly, and in any event by 5:00 p.m. (Eastern time) on the same Business Day as its receipt or deemed receipt of the same, distribute to the applicable Funding Agent for the benefit of the applicable Person, or upon the order of the applicable Funding Agent for the benefit of the applicable Person, its pro rata share (or other applicable share as provided herein) of such payment by wire transfer in like funds as received. Except as otherwise provided in Section 2.07 and Section 4.02, all amounts payable to the Swingline Lender or the L/C Provider hereunder or with respect to the Swingline Loans and L/C Obligations shall be made to or upon the order of the Swingline Lender or the L/C Provider, respectively, by wire transfer of immediately available funds in Dollars not later than 3:00 p.m. (Eastern time) on the date due. Any funds received after that time on such date will be deemed to have been received on the next Business Day. The Master Issuer’s obligations hereunder in respect of any amounts payable to any Investor shall be discharged to the extent funds are disbursed by the Master Issuer to the Administrative Agent as provided herein or by the Trustee or Paying Agent in accordance with Section 4.02, whether or not such funds are properly applied by the Administrative Agent or by the Trustee or Paying Agent. The Administrative Agent’s obligations hereunder in respect of any amounts payable to any Investor shall be discharged to the extent funds are disbursed by the Administrative Agent to the applicable Funding Agent as provided herein whether or not such funds are properly applied by such Funding Agent.
Claims Review Methodology a. C laims Review Population. A description of the Population subject to the Quarterly Claims Review.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
