AML/KYC Procedures “AML/KYC Procedures” means the customer due diligence (CDD) procedures of a Reporting Financial Institution pursuant to the anti-money laundering or similar requirements of the jurisdiction concerned to which such Reporting Financial Institution is subject.
CLAIM PROCEDURES Claim forms or claim information as to the subject policy can be obtained by contacting Benmark, Inc. (800-544-6079). When the Named Fiduciary has a claim which may be covered under the provisions described in the insurance policy, they should contact the office named above, and they will either complete a claim form and forward it to an authorized representative of the Insurer or advise the named Fiduciary what further requirements are necessary. The Insurer will evaluate and make a decision as to payment. If the claim is payable, a benefit check will be issued in accordance with the terms of this Agreement. In the event that a claim is not eligible under the policy, the Insurer will notify the Named Fiduciary of the denial pursuant to the requirements under the terms of the policy. If the Named Fiduciary is dissatisfied with the denial of the claim and wishes to contest such claim denial, they should contact the office named above and they will assist in making an inquiry to the Insurer. All objections to the Insurer's actions should be in writing and submitted to the office named above for transmittal to the Insurer.
Claims Procedures Each Party entitled to be indemnified by the other Party (an “Indemnified Party”) pursuant to Section 8.1 or 8.2 hereof shall give notice to the other Party (an “Indemnifying Party”) promptly after such Indemnified Party has actual knowledge of any threatened or asserted claim as to which indemnity may be sought, and shall permit the Indemnifying Party to assume the defense of any such claim or any litigation resulting therefrom; provided:
Compliance with Privacy Code The parties acknowledge that the Warrant Agent may, in the course of providing services hereunder, collect or receive financial and other personal information about such parties and/or their representatives, as individuals, or about other individuals related to the subject matter hereof, and use such information for the following purposes:
Procurement procedures 11.1 The Recipient must secure the best value for money and shall act in a fair, open and non-discriminatory manner in all purchases of goods and services.
Subcontract Procedures Without relieving it of, or in any way limiting, its obligations to NYSERDA under this Agreement, the Contractor may enter into Subcontracts for the performance of Work or for the purchase of materials or equipment. Prior to beginning any Work, Contractor shall notify the NYSERDA Project Manager of all subcontractors performing work under the Agreement, as well as all changes in subcontractors throughout the term of the Agreement. Except for a subcontractor or supplier specified in a team arrangement with the Contractor in the Contractor’s original proposal, and except for any subcontract or order for equipment, supplies or materials from a single subcontractor or supplier totaling less than $50,000, the Contractor shall select all subcontractors or suppliers through a process of competitive bidding or multi-source price review. A team arrangement is one where a subcontractor or supplier specified in the Contractor’s proposal is performing a substantial portion of the Work and is making a substantial contribution to the management and/or design of the Project. In the event that a competitive bidding or multi-source price review is not feasible, the Contractor shall document an explanation for, and justification of, a sole source selection. The Contractor shall document the process by which a subcontractor or supplier is selected by making a record summarizing the nature and scope of the work, equipment, supplies or materials sought, the name of each person or organization submitting, or requested to submit, a bid or proposal, the price or fee bid, and the basis for selection of the subcontractor or supplier. An explanation for, and justification of, a sole source selection must identify why the work, equipment, supplies or materials involved are obtainable from or require a subcontractor with unique or exceptionally scarce qualifications or experience, specialized equipment, or facilities not readily available from other sources, or patents, copyrights, or proprietary data. All Subcontracts shall contain provisions comparable to those set forth in this Agreement applicable to a subcontractor or supplier, and those set forth in Exhibit C to the extent required by law, and all other provisions now or hereafter required by law to be contained therein. Each Subcontract shall make express reference to this Agreement, and shall state that in the event of any conflict or inconsistency between any Subcontract and this Agreement, the terms and conditions of this Agreement shall control as between Subcontractor and Contractor. For each Subcontract valued at $100,000 or more, the Contractor shall obtain and maintain, pursuant to Section 4.05, a completed Vendor Assurance of No Conflict of Interest or Detrimental Effect form from such Subcontractor prior to the execution of the Subcontract. Such form shall be made available to the Contractor by NYSERDA. Each such Subcontract shall contain a provision whereby the Subcontractor warrants and guarantees that there is and shall be no actual or potential conflict of interest that could prevent the Subcontractor’s satisfactory or ethical performance of duties required to be performed pursuant to the terms of the Subcontract and that the Subcontractor shall have a duty to notify NYSERDA immediately of any actual or potential conflicts of interest. If this Agreement includes a provision requiring Contractor to make Payments to NYSERDA for the Sale or Licensing of a Product, each Subcontract shall include the provisions of Section 8.02, suitably modified to identify the parties. The Contractor shall submit to NYSERDA’s Contract Administrator for review and written approval any subcontract(s) specified in the Statement of Work as requiring NYSERDA approval, including any replacements thereof.
CUSTOMS PROCEDURES 1. Each Party shall endeavour to apply its customs procedures in a predictable, consistent and transparent manner.
COMPLIANCE WITH NEW YORK STATE INFORMATION SECURITY BREACH AND NOTIFICATION ACT Contractor shall comply with the provisions of the New York State Information Security Breach and Notification Act (General Business Law Section 899-aa; State Technology Law Section 208).
Compliance with Privacy Laws NCPS represents and warrants that its collection, access, use, storage, disposal and disclosure of Personal Data does and will comply with all applicable federal and state privacy and data protection laws, as well as all other applicable regulations. Without limiting the foregoing, NCPS shall implement administrative, physical and technical safeguards to protect Personal Data that are no less rigorous than accepted industry, and shall ensure that all such safeguards, including the manner in which Personal Data is collected, accessed, used, stored, processed, disposed of and disclosed, comply with applicable data protection and privacy laws, as well as the terms and conditions of this Escrow Agreement. NCPS shall use and disclose Personal Data solely and exclusively for the purposes for which the Personal Data, or access to it, is provided pursuant to the terms and conditions of this Escrow Agreement, and not use, sell, rent, transfer, distribute, or otherwise disclose or make available Personal Data for NCPS’s own purposes or for the benefit of any party other than Issuer. For purposes of this section, “Personal Data” shall mean information provided to NCPS by or at the direction of the Issuer, or to which access was provided to NCPS by or at the direction of the Issuer, in the course of NCPS’s performance under this Escrow Agreement that: (i) identifies or can be used to identify an individual (also known as a “data subject”) (including, without limitation, names, signatures, addresses, telephone numbers, e-mail addresses and other unique identifiers); or (ii) can be used to authenticate an individual (including, without limitation, employee identification numbers, government-issued identification numbers, passwords or PINs, financial account numbers, credit report information, biometric or health data, answers to security questions and other personal identifiers), including the identifying information on individuals described in Section 12.
SAFETY PROCEDURES The Contractor shall:
