FAA Type Certification Basis Sample Clauses

FAA Type Certification Basis. (a) The FAA shall develop its type certification basis using the applicable airworthiness standards (14 CFR) in effect on the date application was made to EASA, or where applicable an AA, for its type certificate. (When 14 CFR part 26 applies to a European transport category airplane, the applicable standard is the amendment in effect on the date the FAA type certificate is issued.)
Sample 1Sample 2Sample 3See All (4)
AutoNDA by SimpleDocs
FAA Type Certification Basis. (a) The FAA shall develop its type certification basis using the applicable airworthiness standards (14 CFR) in effect on the date application was made to EASA, or where applicable an AA, for its type certificate. (When 14 CFR part 26 applies to a European transport category airplane, the applicable standard is the amendment in effect on the date the FAA type certificate is issued.) (b) The applicable airworthiness requirements may be supplemented with the following additional requirements: (1) Special conditions: The FAA shall review all novel and unusual design features for development of special conditions. (2) Technical requirements necessary in the interest of safety: These include requirements to preclude a potential unsafe condition finding for the product under 14 CFR 21.21(b)(2). These may be generated as a result of adverse service history of this product, or other products of a similar nature or design. This includes, but is not limited to, actions taken by EASA to correct unsafe conditions. 2.1.3.2
Sample 1

Related to FAA Type Certification Basis

  • CONTRACT EXHIBIT I PREFERRED PRICING AFFIDAVIT This preferred-pricing affidavit is entered into in accordance with section 216.0113, F.S., and as required by Contract No. 80101507-21-STC-ITSA (“Contract”) between (“Contractor”) and the Department of Management Services. As the person authorized by Contractor to sign this affidavit, I attest that the Contractor is in full compliance with the preferred-pricing clause of the Contract. Contractor’s Name: By: Signature Printed Name/Title Date: STATE OF COUNTY OF Sworn to (or affirmed) and subscribed before me this day of , by . Signature of Notary Vendor Name: FEIN# Vendor’s Authorized Representative Name and Title: Address: City, State, and Zip code: Phone Number: ( ) - E-mail: CORPORATE SEAL (IF APPLICABLE) (Print, Type, or Stamp Commissioned Name of Notary Public) [Check One] Personally Known OR Produced the following I.D.

  • AS9100 Certification ‌ AS9100 Certification, specifies requirements for a quality management system to demonstrate the Contractor’s ability to consistently meet the customer requirements as well as statutory and regulatory requirements for the aerospace industry. An AS9100 Certification, is not mandatory; however, Contractors who desire to compete for work within the aerospace industry are encouraged to have AS9100 Certification, during the entire term of OASIS. The Contractor shall notify the OASIS CO, in writing, if there are any changes in the status of their AS9100 Certification, and provide the reasons for the change and copies of audits from an AS9100 Certification Body, as applicable. If only part of a Contractor’s organization is AS9100, certified, the Contractor shall make the distinction between which business units or sites and geographic locations have been certified.

  • ISO 9001 Certification The Contractor shall maintain or exceed their ISO 9001 Certification and submit updates, if applicable

  • Special Certification The individual or officer signing this agreement certifies by his or her signature that he or she is authorized to sign this agreement on behalf of the responsible governing board, official or Grantee.

  • E-VERIFY CERTIFICATION Pursuant to Executive Order RP-80, Engineer certifies and ensures that for all contracts for services, Engineer shall, to the extent permitted by law, utilize the United States Department of Homeland Security’s E-Verify system during the term of this agreement to determine the eligibility of:

  • Instructions for Certification 1. By signing and submitting this CONTRACT, the prospective lower tier participant is providing the certification set out below.

  • Owner Certification During the term of this Contract, the Owner certifies that:

  • Employee Certification Employee hereby certifies that he has had an adequate opportunity to review, and understands all the terms and conditions of, this Agreement.

  • Contractor Certification Clauses Contractor represents and warrants that the following statements are true. During the term of the Agreement, Contractor shall not take an action, or omit to perform any act, that results in a representation and warranty becoming untrue. Contractor shall promptly notify the Judicial Council if any representation and warranty becomes untrue.

  • Drug-Free Workplace Certification As required by Executive Order No. 90-5 dated April 12, 1990, issued by the Governor of Indiana, the Contractor hereby covenants and agrees to make a good faith effort to provide and maintain a drug-free workplace. The Contractor will give written notice to the State within ten (10) days after receiving actual notice that the Contractor, or an employee of the Contractor in the State of Indiana, has been convicted of a criminal drug violation occurring in the workplace. False certification or violation of this certification may result in sanctions including, but not limited to, suspension of contract payments, termination of this Contract and/or debarment of contracting opportunities with the State for up to three (3) years. In addition to the provisions of the above paragraph, if the total amount set forth in this Contract is in excess of $25,000.00, the Contractor certifies and agrees that it will provide a drug-free workplace by:

Time is Money Join Law Insider Premium to draft better contracts faster.