First sampling. In the first sampling four rear marking plates are selected at random. The first sample of two is marked A, the second sample of two is marked B. 2.1. The conformity is not contested 2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall not be contested if the deviation of the measured values of the rear marking plates in the unfavourable directions are: 2.1.1.1. sample A A1: one rear marking plate 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. sample B 2.2. The conformity is contested 2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates are: 2.2.1.1. sample A A3: one rear marking plate not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.2.1.2. sample B B2: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 30 per cent 2.3. Approval withdrawn 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per cent 2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per cent
Appears in 2 contracts
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation deviations of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate headlamp 0 per cent one rear marking plate headlamp not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but not more than 20 per cent go Go to sample B 2.1.1.2. sample BSample B B1: both headlamps 0 per cent
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample Sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample Sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawnwithdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:
2.3.1. sample Sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample Sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per cent
Appears in 2 contracts
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate headlamp one headlamp not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent go to sample B cent
2.1.1.2. Sample B B1: both headlamps 0 per cent
2.1.2. Or, if the conditions of paragraph 1.2.2. above for sample BA are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A : A3: one rear marking plate headlamp one headlamp but not more than more than not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent
2.2.1.2. sample cent Sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp but more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate not more than 20 per cent 30 per cent
2.2.1.1. Sample A 2.2.1.2.
2.2.2. Or, if the conditions of paragraph 1.2.2. above for sample A are not fulfilled.
2.3. Approval withdrawn Conformity shall be contested and paragraph 12. of this Regulation applied if, following the sampling procedure in Figure 1 of this annex, the deviations of the measured values of the headlamps are: A4: one rear marking plate headlamp one headlamp not more than more than 20 per cent 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample cent Sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but one headlamp not more than more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per centcent 2.3.1. Sample A 2.3.2.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp 0 per cent one rear marking plate headlamp not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. sample BB B1: both headlamps 0 per cent
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per cent
Appears in 1 contract
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate headlamp one headlamp not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent go to sample B cent
2.1.1.2. Sample B B1: both headlamps 0 per cent
2.1.2. Or, if the conditions of paragraph 1.2.2. above for sample BA are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A : A3: one rear marking plate headlamp one headlamp but not more than more than not more than 20 per cent one rear marking plate more than 20 per cent but not more than 30 per cent
2.2.1.2. sample cent Sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp but more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate not more than 20 per cent 30 per cent
2.2.1.1. Sample A 2.2.1.2.
2.2.2. Or, if the conditions of paragraph 1.2.2. above for sample A are not fulfilled.
2.3. Approval withdrawn Conformity shall be contested and paragraph 10. applied if, following the sampling procedure in Figure 1 of this annex, the deviations of the measured values of the headlamps are: A4: one rear marking plate headlamp one headlamp not more than more than 20 per cent 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample cent Sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but one headlamp not more than more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per centcent 2.3.1. Sample A 2.3.2.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested:
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate One headlamp 0 per cent one rear marking plate One headlamp not more than 20 per cent A2: both rear marking plates Both headlamps more than But not more than Go to sample B 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. Sample B B1: Both headlamps 0 per cent
2.1.2. Or if the conditions of paragraph 1.2.2. for sample BA are fulfilled.
2.2. The conformity is contested:
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample Sample A A3: one rear marking plate One headlamp not more than 20 per cent one rear marking plate One headlamp more than 20 per cent but But not more than 30 per cent
2.2.1.2. sample Sample B B2: in In the case of A2 one rear marking plate One headlamp more than 0 per cent but But not more than 20 per cent one rear marking plate One headlamp not more than 20 per cent B3: in In the case of A2 one rear marking plate One headlamp 0 per cent one rear marking plate One headlamp more than 20 per cent but But not more than 30 per cent
2.2.2. Or if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawnwithdrawn Conformity shall be contested and paragraph 10. applied if, following the sampling procedure in Figure 1 of this annex, the deviations of the measured values of the headlamps are:
2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per centSample A
2.3.2. sample Sample B B4: in In the case of A2 one rear marking plate One headlamp more than But not more than One headlamp more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in In the case of A2 both rear marking plates Both headlamps more than 20 per cent B6: in In the case of A2 one rear marking plate One headlamp One headlamp more than 0 per cent one rear marking plate more than 30 per cent
2.3.3. Or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp 0 per cent one rear marking plate headlamp not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. sample BB B1: both headlamps 0 per cent 2/ See footnote 15/ of the text of the Regulation.
2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 one headlamp not more than 20 per per cent cent B3: in the case of A2 one headlamp 0 per cent one headlamp more than 20 per cent but not more than 30 per cent
2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawn
2.3.1. sample A
2.3.2. sample B B4: in the case of A2 one headlamp more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of both headlamps A2 both rear marking plates more than 20 per cent B6: in the case of one headlamp A2 one rear marking plate 0 per cent one rear marking plate headlamp more than 30 per centcent 2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested:
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate One headlamp 0 per cent one rear marking plate One headlamp not more than 20 per cent A2: both rear marking plates Both headlamps more than 0 per cent but But not more than 20 per cent go Go to sample B 2.1.1.2. Sample B B1: Both headlamps 0 per cent
2.1.2. Or if the conditions of paragraph 1.2.2. for sample BA are fulfilled.
2.2. The conformity is contested:
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A : A3: one rear marking plate One headlamp not more than One headlamp more than But not more than 20 per cent one rear marking plate 20 per cent 30 per cent Sample B B2: In the case of A2 One headlamp more than But not more than One headlamp not more than 0 per cent 20 per cent 20 per cent B3: In the case of A2 One headlamp One headlamp more than But not more than 0 per cent 20 per cent 30 per cent
2.2.1.1. Sample A 2.2.1.2.
2.2.2. Or if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawn Conformity shall be contested and paragraph 10. applied if, following the sampling procedure in Figure 1 of this annex, the deviations of the measured values of the headlamps are: A4: One headlamp not more than One headlamp more than 20 per cent but not 30 per cent A5: Both headlamps more than 30 20 per cent
2.2.1.2. sample cent Sample B B2B4: in In the case of A2 one rear marking plate One headlamp more than But not more than One headlamp more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in In the case of A2 both rear marking plates Both headlamps more than 20 per cent B6: in In the case of A2 one rear marking plate One headlamp One headlamp more than 0 per cent one rear marking plate more than 30 per cent
2.3.1. Sample A 2.3.2.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp 0 per cent one rear marking plate headlamp not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but not more than 20 per cent go to sample B B
2.1.1.2. sample BB B1: both headlamps 0 per cent
2.1.2. or if the conditions of paragraph 1.2.2. for sample A are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.2. or if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per cent
2.3.3. or if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates retro-reflectors are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates retro-refle ctors shall not be contested if the deviation of the measured values of the rear marking plates retro-reflectors in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate retro-reflector one retro-reflector not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates retro-reflectors more than but not more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2B
1.1.2. sample BB B1: both retro-reflectors 0 per cent
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates retro-reflectors shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates retro-reflectors are:
2.2.1.1. sample A A3: one rear marking plate retro-reflector not more than 20 per cent one rear marking plate retro-reflector more than but not more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate retro-reflector more than but not more than one retro-reflector not more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate retro-reflector 0 per cent one rear marking plate retro-reflector more than 20 per cent but not more than 30 per cent
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate retro-reflector not more than 20 per cent A5: one rear marking plate retro-reflector more than both retro-reflectors more than 30 per cent A5: both rear marking plates more than 20 per centcent Annex 18
2.3.2. sample B B4: in the case of A2 one rear marking plate retro-reflector more than but not more than one retro-reflector more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates retro-reflectors more than 20 per cent B6: in the case of A2 one rear marking plate retro-reflector one retro-reflector more than 0 per cent one rear marking plate more than 30 per cent
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp 0 per cent one rear marking plate headlamp not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but not more than 20 per cent go to sample B 2.1.1.2. sample BB B1: both headlamps 0 per cent
2.1.2. or, if the conditions of paragraph 1.2.2. for sample A are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.2. or, if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per cent
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation deviations of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp one headlamp not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates headlamps more than 0 per cent but But go to sample B not more than 20 per cent go to cent
1.1.2. sample B 2.1.1.2. sample BB1: both headlamps 0 per cent
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
cent 2.3. Approval withdrawn
withdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in Figure 1 of this annex, the deviations of the measured values of the headlamps are: 2.3.1. sample A A4: one rear marking plate not more than 20 per cent one rear marking plate more than 30 per cent A5: both rear marking plates more than 20 per centA
2.3.2. sample B B4: in the case of A2 one rear marking plate headlamp but one headlamp more than not more than more than 0 per cent 20 per cent 20 per cent B5: in the case of A2 both headlamps more than 20 per cent B6: in the case of A2 one headlamp 0 per cent one headlamp more than 30 per cent 3. REPEATED SAMPLING In the case of A3, B2, B3 a repeated sampling, third sample C of two headlamps, selected from stock manufactured after alignment, is necessary within two months' time after the notification.
3.1. The conformity is not contested
3.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall not be contested if the deviations of the measured values of the headlamps are:
3.1.1.1. sample C C1: one headlamp one headlamp not more than 0 per cent 20 per cent C2: both headlamps but go to sample D more than not more than 0 per cent 20 per cent
3.1.1.2. sample D D1: in the case of C2 both headlamps 0 per cent
3.2. The conformity is contested
3.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the headlamps are:
3.2.1.1. sample D D2: in the case of C2 one headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp not more than 20 per cent
3.3. Approval withdrawn
3.3.1. sample C
3.3.2. sample D D3: in the case of C2 one headlamp 0 or more than 0 per cent one headlamp more than 20 per cent B5Abbreviations: in P: passing beam lamp D: driving beam lamp (D1 + D2 means two driving beams) F: front fog lamp : means a cycle of 15 minutes off and 5 minutes lit. All following grouped headlamps and front fog lamps together with the case of A2 both rear added class B marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per centsymbols are given as examples and are not exhaustive.
1. P or D or F (C-BS or R-BS or B) P, D or F 2. P+D (CR-BS) or P+D1+D2 (CR-BS R-BS)
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample A A1: one rear marking plate headlamp one headlamp not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent go to sample B cent
2.1.1.2. sample BB B1: both headlamps 0 per cent
2.1.2. or, if the conditions of paragraph 1.2.2. for sample A are fulfilled.
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.2. sample B B2: in the case of A2 one rear marking plate headlamp more than 0 per cent but one headlamp not more than not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp but more than not more than 20 per cent but not more than 30 per cent
2.2.2. or, if the conditions of paragraph 1.2.2. for sample A are not fulfilled.
2.3. Approval withdrawn
2.3.1. sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample B B4: in the case of A2 one rear marking plate headlamp more than 0 per cent but not more than 20 per cent one rear marking plate headlamp more than 20 per cent B5: in the case of A2 both rear marking plates headlamps more than 20 per cent B6: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp more than 30 per cent
2.3.3. or, if the conditions of paragraph 1.2.2. for samples A and B are not fulfilled.
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles
First sampling. In the first sampling four rear marking plates headlamps are selected at random. The first sample of two is marked A, the second sample of two is marked B.
2.1. The conformity is not contested
2.1.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall not be contested if the deviation deviations of the measured values of the rear marking plates headlamps in the unfavourable directions are:
2.1.1.1. sample Sample A A1: one rear marking plate headlamp one headlamp not more than 0 per cent one rear marking plate not more than 20 per cent A2: both rear marking plates headlamps but go to sample B more than not more than 0 per cent but not more than 20 per cent go to sample B cent
2.1.1.2. sample BSample B B1: both headlamps 0 per cent
2.2. The conformity is contested
2.2.1. Following the sampling procedure shown in Figure figure 1 of this annex the conformity of mass-produced rear marking plates headlamps shall be contested and the manufacturer requested to make his production meet the requirements (alignment) if the deviations of the measured values of the rear marking plates headlamps are:
2.2.1.1. sample Sample A A3: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 20 per cent but not more than 30 per cent
2.2.1.22.1.2. sample Sample B B2: in the case of A2 one rear marking plate headlamp but one headlamp more than not more than not more than 0 per cent but not more than 20 per cent one rear marking plate not more than 20 per cent B3: in the case of A2 one rear marking plate headlamp 0 per cent one rear marking plate headlamp but more than not more than 20 per cent but not more than 30 per centcent Annex 7
2.3. Approval withdrawnwithdrawn Conformity shall be contested and paragraph 11. applied if, following the sampling procedure shown in figure 1 of this annex, the deviations of the measured values of the headlamps are:
2.3.1. sample Sample A A4: one rear marking plate headlamp not more than 20 per cent one rear marking plate headlamp more than 30 per cent A5: both rear marking plates headlamps more than 20 per cent
2.3.2. sample Sample B B4: in the case of A2 one rear marking plate more than 0 per cent but not more than 20 per cent one rear marking plate more than 20 per cent B5: in the case of A2 both rear marking plates more than 20 per cent B6: in the case of A2 one rear marking plate 0 per cent one rear marking plate more than 30 per centA2
Appears in 1 contract
Samples: Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles