Manufacture and Supply As between the Parties, Otsuka shall be responsible for, shall bear all costs associated with, and shall have all decision-making authority over, all Manufacturing Activities (subject to discussion of CMC matters with Acucela through the JDC or applicable Operating Team as discussed below); provided, that Otsuka shall supply Licensed Product to Acucela or its permitted subcontractors for use in clinical trials conducted in accordance with each Development Plan and, if applicable, Commercialization Plan (i.e., Phase 3b Clinical Trials or Post-Approval Studies, if any), free of charge and in such quantities as are agreed by the JDC or the JCC (as applicable) or are otherwise required to seek or obtain Regulatory Approval. In addition, if and after Acucela exercises an Opt-In Right under Section 3.1, Otsuka shall supply promotional samples of Licensed Product to Acucela for use in its performance of Co-Promotion, in such quantities and on such terms as are determined by the JCC. The cost of promotional samples of Licensed Product, which shall be included in Commercialization Costs, shall be established by the JCC based on Otsuka’s per-unit cost to manufacture such promotional samples (but, for the avoidance of doubt, Otsuka shall have no obligation to disclose any information relating to its manufacturing costs), but in no event shall such promotional sample cost exceed * per promotional sample unless mutually agreed otherwise by the Parties. Acucela’s and its permitted subcontractors’ obligations to conduct Development activities, and upon Acucela’s exercise of its Opt-in Right pursuant to Section 3.1, to conduct Development and Commercialization activities, shall be expressly conditioned upon Otsuka fulfilling its Licensed Product supply obligations as set forth in the Development Plan or the Commercialization Plan, as applicable. To the extent that Otsuka reasonably believes is necessary for performance of Development or Commercialization, Otsuka agrees to keep Acucela reasonably informed from time to time, through the JDC, JCC or applicable Operating Team, regarding the general status of Manufacturing Activities related to the Licensed Product (including Other Indication Product(s), as applicable) and from time to time shall update Acucela on any foreseeable delays and/or other material issues relating to Manufacturing the Licensed Product (including Other Indication Product(s), as applicable). Through the JDC or applicable Operating Team, Otsuka and Acucela shall confer and discuss CMC matters, and Otsuka agrees to consider suggestions of Acucela regarding CMC matters.
Supply Agreement Seller and Buyer, or their Affiliates, shall have executed the Supply Agreement.
Supply Agreements For a period of three years from the consummation of the IPO, Odetics shall not unilaterally terminate or assign its guarantee obligation with respect to any supply agreement pursuant to which it has guaranteed the performance by ATL of ATL's obligations, unless such suppliers have consented to the termination or assignment of such guarantee.
Manufacturing and Supply (a) Depomed shall supply Product for use in conducting Depomed’s development activities for Product in the Field and in the Territory as set forth in Exhibit D.
(b) During the four-year period beginning on the Effective Date (the “Supply Period”), Depomed shall supply and package (or have supplied and packaged) Product pursuant to this Section 4.8. Depomed will use commercially reasonable efforts to enter into a long-term Product supply agreement with [***] days after the Effective Date (the “Depomed Supply Agreement”) that will be freely assignable to Solvay or its Affiliates, successors or assigns at any time. In addition, Depomed and Solvay will negotiate and enter into a Product supply agreement with business terms substantially similar to the Depomed Supply Agreement concurrently with the execution and delivery by Depomed and [***] of the Depomed Supply Agreement (the “Solvay Supply Agreement”, and, together with the Depomed Supply Agreement, the “Supply Agreements”). The Supply Agreements will, together, contain the following provisions (among others mutually agreeable to the Parties):
(i) Under the Solvay Supply Agreement, Depomed will agree to supply Solvay with its requirements of finished, packaged Product during the Supply Period;
(ii) All manufacturing and records will be performed and maintained in accordance with specifications, cGMP and Applicable Law;
(iii) Depomed will provide reasonable assistance to Solvay in the event Solvay wishes to qualify a backup Product manufacturer;
(iv) Depomed shall [***];
(v) Solvay will pay Depomed the following amounts in connection with all activities performed by or on behalf of Depomed associated with Product manufacture and supply (other than activities specified on Exhibit D) (A) [***]% of Depomed’s out-of-pocket costs incurred in connection with such manufacture and supply of Product to Solvay, and (B) a labor charge equal to the FTE Charges for all Depomed employees allocated to the manufacture and supply of Product to Solvay, not to exceed FTE Charges for an aggregate of [***] during any given calendar quarter (and Depomed shall provide to Solvay periodic reports detailing the FTE Charges for which Solvay must pay Depomed hereunder);
Other Products and Services As our customer, you have access to a suite of financial products and services availed by ourselves, our affiliates and strategic partners designed to help you address and achieve your financial needs and goals. You agree that you can obtain information about such Products and Services via our website xxx.xxxxxxxx.xxx.xx and you further agree that we can from time to time communicate information in relation to such Products or Services to you specifically or generally to all cardmembers via such communication mode as we consider appropriate.
Service Agreement Refers to the Contract, Purchase Order or Terms of Service or Terms of Use. Student Data: Student Data includes any data, whether gathered by Provider or provided by LEA or its users, students, or students’ parents/guardians, that is descriptive of the student including, but not limited to,
Additional Products and Services Subject to the allocation of funds, the CPO may add similar equipment, supplies, services, or locations, within the scope of this Agreement, to the list of equipment, supplies, services, or locations to be performed or provided by giving written notification to Contractor. For purposes of this Section, the “Effective Date” means the date specified in the notification from the CPO. As of the Effective Date, each item added is subject to this Agreement, as if it had originally been a part, but the charge for each item starts to accrue only on the Effective Date. In the event the additional equipment, supplies, services, or locations are not identical to the items(s) already under this Agreement, the charges therefor will then be Contractor’s normal and customary charges or rates for the equipment, supplies, services, or locations classified in the Fees and Costs (Exhibit “F”).
Manufacture of Products All Products marketed through Grantor's Web ------------------------- Site shall be manufactured, packaged, prepared, and shipped in accordance with the specifications and requirements described on Exhibit A hereto as it may be modified from time to time. Quality control standards relating to the Product's weight, color, consistency, micro-biological content, labeling and packaging are also set forth on Exhibit A. In the event that Exhibit A is incomplete, Products shall be manufactured and shipped in accordance with industry standards.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
Contract Negotiations Where operational requirements permit, and on reasonable notice, the Employer shall grant special leave with pay for not more than two (2) representatives of each bargaining unit for the purpose of attending contract negotiation meetings with the Employer on behalf of the Union. Such permission shall not be unreasonably withheld.
