Manufacturing Capacity and Reservations Sample Clauses

Manufacturing Capacity and Reservations. NOVASEP will, on agreement of, and in accordance with, a Work Plan, reserve slots in its cGMP manufacturing suite for those cGMP Batches to be manufactured under the relevant Work Plan according to the time frame in that Work Plan. Where the time frame is amended in accordance with section 2.13 of this Agreement (amongst other sections) and such amendment affects the existing manufacturing schedule for Batches, NOVASEP will use reasonable endeavours to update its manufacturing schedule and reserve new slots for those affected Batches which will be reserved as near in time to the existing vacated slots as NOVASEP’s then current schedule will permit. CUSTOMER may delay or cancel any slot reservation at any time upon prior written notice to NOVASEP subject to the payment of the delay and cancellation payments set out in Section 2.13 or Part 9 as applicable, and NOVASEP shall accordingly modify the time frame by delaying performance of those applicable Works associated with such delayed or cancelled slot.
Sample 1Sample 2
AutoNDA by SimpleDocs

Related to Manufacturing Capacity and Reservations

  • Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time. (b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.

  • Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.

  • Testing Capabilities 7.2.2.10.2.1 LIS Acceptance Testing is provided where equipment is available, with the following test lines: seven-digit access to balance (100 type), milliwatt (102 type), nonsynchronous or synchronous, automatic transmission measuring (105 type), data transmission (107 type), loop-around, short circuit, open circuit, and non-inverting digital loop-back (108 type), and such other acceptance testing that may be needed to ensure that the service is operational and meets the applicable technical parameters. 7.2.2.10.2.2 In addition to LIS acceptance testing, other tests are available (e.g., additional cooperative acceptance testing, automatic scheduled testing, cooperative scheduled testing, manual scheduled testing, and non-scheduled testing). Charges for such testing are identified in Section 7.3.5.

  • Packaging Materials and Containers for Retail Sale 1. When packaging materials and containers in which a good is packaged for retail sales are classified in the Harmonized System with the good, they shall not be taken into account in determining whether all non-originating materials used in the production of the good undergo the applicable change in tariff classification set out in Annex 4.03. 2. When the good is subject to a requirement of regional value content, the value of these packaging materials and containers shall be taken into account as originating or non-originating materials, as the case may be, in calculating the regional value content of the good.

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Consumables During the design phase, Purchaser may participate in the selection of suppliers of consumables of the Supplier. In such case, the choice regarding the final selection of the said suppliers shall be mutually agreed between the Parties. Two suppliers shall be identified and selected for each type of consumables.

  • Fuel The Vehicle must be returned with the amount of fuel equal to that at the time of the commencement of the rental. If the Vehicle is returned with less fuel, the difference will be charged to You at a rate of $5.00 per litre (which includes a service component).

  • Generators Temporary installation of generators, and permanent installation of generators that are placed inside existing non-residential buildings or that occupy an area under 50 square feet behind the building they serve.

  • Interconnection Customer Provided Services The services provided by Interconnection Customer under this LGIA are set forth in Article 9.6 and Article 13.5. 1. Interconnection Customer shall be paid for such services in accordance with Article 11.6.

  • Manufacturing Rights (a) If QED fails to supply Product ordered by ViewRay in accordance with the terms of this Agreement regarding the quantity or quality of Products supplied to ViewRay, then QED shall within fifteen (15) Business Days of said failure present ViewRay with a plan to remedy the problem and shall use Commercially Reasonable Efforts to execute such plan and remedy the problem or QED shall secure an alternative source of supply within a reasonable time at no additional cost to ViewRay. Any such alternative source of supply shall be on terms substantially identical with the terms of this Agreement. If QED is unable to provide a plan to remedy the problem or secure an alternative source of supply within [***] after its initial failure to supply, then QED shall consult with ViewRay and the parties shall work together to remedy the problem. If QED is unable to remedy the supply problem after [***] (or longer as agreed in writing by the parties), commencing with the date upon which such failure to supply began, then ViewRay may at its option, and upon notice to QED, manufacture the Products itself or through a third party in accordance with the provisions of Section 3.10(b). [***] Certain information in this document has been omitted and filed separately with the Securities and Exchange Commission. Confidential treatment has been requested with respect to the omitted portions. (b) If ViewRay notifies QED pursuant to Section 3.10(a), above, that ViewRay will manufacture the Products itself or through a third party, QED shall (i) deliver to ViewRay within thirty (30) days media embodying or disclosing all Program technology and Program proprietary or intellectual property rights necessary to enable ViewRay or its designee to manufacture Products conforming with the Specifications; and (ii) provide ViewRay or its designee, upon request, with reasonable assistance in establishing a back-up manufacturing line. ViewRay shall require any third party ViewRay designates to manufacture Products pursuant to this Section 3.10, to agree in writing to observe the terms of this Agreement relating to confidentiality and the manufacture of Products. Notwithstanding any provision of this Section 3.10 to the contrary, in no case shall QED be required to pay ViewRay in respect of any Products purchased by ViewRay from a third party operating a back-up manufacturing line established pursuant to this Section 3.10 or manufactured by ViewRay or its Affiliates pursuant to this Section 3.10.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!