Common use of Operational Standards Clause in Contracts

Operational Standards. Member shall operate and maintain in good order and repair, all without cost to the Cooperative, all equipment required for the safe operation of the Member Facility operating in parallel with the Cooperative's electrical supply and distribution system. Equipment required for safe operation shall include, but not be limited to, equipment necessary to (1) establish and maintain automatic synchronism with the Cooperative's electrical supply and distribution system and (2) automatically disconnect the Member Facility from the Cooperative's electrical supply and distribution system in the event of an overload or outage, including loss of one or more phases of a three phase service, on the Cooperative's electrical supply and distribution system. The Member Facility shall be designed to operate within allowable operating standards for the Cooperative's electrical supply and distribution system. The Member Facility shall not cause any adverse effects upon the quality or reliability of service provided to the Cooperative's other members. Member shall operate its Member Facility in accordance with all applicable rules, laws, and regulations including, but not limited to, IEEE 519 and 1547. Member shall provide a device to disconnect Member Facility from Cooperative’s electrical distribution facilities that is accessible and in reasonably close proximity to the billing meter. Member shall obtain any permits required by governmental authorities prior to construction, installation, and interconnection of the Member Facility. Member shall also maintain compliance with these permits during the term of this Agreement.

Operational Standards. Member shall operate and maintain in good order and repair, all without cost to the Cooperative, all equipment required for the safe operation of the Member Facility operating in parallel with the Cooperative's ’s electrical supply and distribution systemsys- tem. Equipment required for safe operation shall include, but not be limited to, equipment necessary to (1) establish and maintain automatic synchronism with the Cooperative's ’s electrical supply and distribution system and (2) automatically disconnect the Member Facility from the Cooperative's ’s electrical supply and distribution system in the event of an overload or outage, including loss of one or more phases of a three phase service, on the Cooperative's ’s electrical supply and distribution system. The Member Facility shall be designed to operate within with- in allowable operating standards for the Cooperative's ’s electrical supply and distribution system. The Member Facility shall not cause any adverse effects effects upon the quality or reliability of service provided to the Cooperative's ’s other members. Member shall operate its Member Facility in accordance with all applicable rules, laws, and regulations including, but not limited to, IEEE 519 and 1547. Member shall provide pro- vide a device to disconnect Member Facility from Cooperative’s electrical distribution facilities that is accessible and in reasonably close proximity to the billing meter. Member shall obtain any permits required by governmental authorities prior to construction, installation, and interconnection of the Member Facility. Member shall also maintain compliance with these permits during the term of this Agreement.

Operational Standards. Member shall operate and maintain in good order and repair, all without cost to the Cooperative, all equipment required for the safe operation of the Member Facility operating in parallel with the Cooperative's ’s electrical supply and distribution system. Equipment required for safe operation shall include, but not be limited to, equipment necessary to (1) establish and maintain automatic synchronism syn- chronism with the Cooperative's ’s electrical supply and distribution system and (2) automatically disconnect the Member Facility from the Cooperative's ’s electrical supply and distribution system in the event of an overload or outage, including loss of one or more phases of a three phase service, on the Cooperative's ’s electrical supply and distribution system. The Member Facility shall be designed to operate within allowable al- lowable operating standards for the Cooperative's ’s electrical supply and distribution system. The Member Facility shall not cause any adverse anyadverse effects upon the quality or reliability of service provided to the Cooperative's ’s other members. Member shall operate its Member Facility in accordance with all applicable rules, laws, and regulations including, but not limited to, IEEE 519 and 1547. Member shall provide a device to disconnect Member Facility from Cooperative’s electrical distribution facilities that is accessible and in reasonably close proximity to the billing meter. Member shall obtain any permits required by governmental authorities prior to construction, installation, and interconnection of the Member Facility. Member shall also maintain compliance with these permits during the term of this Agreement.

Operational Standards. Member shall operate and maintain in good order and repair, all without cost to the Cooperative, all equipment required for the safe operation of the Member Facility operating in parallel with the Cooperative's ’s electrical supply and distribution systemsys- tem. Equipment required for safe operation shall include, but not be limited to, equipment necessary to (1) establish and maintain automatic synchronism with the Cooperative's ’s electrical supply and distribution system and (2) automatically disconnect the Member Facility from the Cooperative's ’s electrical supply and distribution system in the event of an overload or outage, including loss of one or more phases of a three phase service, on the Cooperative's ’s electrical supply and distribution system. The Member Facility shall be designed to operate within allowable operating standards for the Cooperative's ’s electrical supply and distribution system. The Member Facility shall not cause any adverse effects effects upon the quality or reliability of service provided to the Cooperative's ’s other members. Member shall operate its Member Facility in accordance with all applicable rules, laws, and regulations including, but not limited to, IEEE 519 and 1547. Member shall provide pro- vide a device to disconnect Member Facility from Cooperative’s electrical distribution facilities that is accessible and in reasonably close proximity to the billing bill ing meter. Member shall obtain any permits required by governmental authorities prior to construction, installation, and interconnection of the Member Facility. Member shall also maintain compliance with these permits during the term of this Agreement.