Updates and Upgrades Contractor grants to the Department a non-exclusive, non-transferable license to use upgrades and updates provided by Contractor during the term of the Contract. Such upgrades and updates are subject to the terms of the Contract. The Department shall download, distribute, and install all updates as released by Contractor during the length of the Contract, and Contractor strongly suggests that the Department also downloads, distributes, and installs all upgrades as released by Contractor during the length of the Contract. Contractor shall use commercially reasonable efforts to provide the Department with work-around solutions or patches to reported software problems that may affect the Department’s use of the software during the length of the Contract.
Samples The Contractor shall submit the following samples of Materials and relevant information to the Authority’s Engineer for pre-construction review:
(a) manufacturer's test reports and standard samples of manufactured Materials; and
(b) samples of such other Materials as the Authority’s Engineer may require.
Training Materials Training Materials will be provided for each student. Training Materials may be used only for either (i) the individual student’s reference during Boeing provided training and for review thereafter or (ii) Customer’s provision of training to individuals directly employed by the Customer.
Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time.
(b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.
Technical Specifications The Technical Specifications furnished on the CD are intended to establish the standards for quality, performance and technical requirements for all labor, workmanship, material, methods and equipment necessary to complete the Work. When specifications and drawings are provided or referenced by the County, these are to be considered part of the Scope of Work, and to be specifically documented in the Detailed Scope of Work. For convenience, the County supplied specifications, if any, and the Technical Specifications furnished on the CD.
Protocols Each party hereby agrees that the inclusion of additional protocols may be required to make this Agreement specific. All such protocols shall be negotiated, determined and agreed upon by both parties hereto.
Tooling Unless otherwise specified in this Agreement, all tooling and/or all other articles required for the performance hereof shall be furnished by Seller, maintained in good condition and replaced when necessary at Seller's expense. If NETAPP agrees to pay Seller for special tooling or other items either separately or as a stated part of the unit price of Goods purchased herein, title to same shall be and remain in NETAPP upon payment therefore.
Product Specifications (a) Supplier shall manufacture all Products according to the Specifications in effect as of the date of this Agreement, with such changes or additions to the Specifications of the Products related thereto as shall be requested by Buyer in accordance with this Section or as otherwise agreed in writing by the Parties. All other Products shall be manufactured with such Specifications as the Parties shall agree in writing.
(b) Buyer may request changed or additional Specifications for any Product by delivering written notice thereof to Supplier not less than one hundred twenty (120) days in advance of the first Firm Order for such Product to be supplied with such changed or additional Specifications. Notwithstanding the foregoing, if additional advance time would reasonably be required in order to implement the manufacturing processes for production of a Product with any changed or additional Specifications, and to commence manufacture and delivery thereof, Supplier shall so notify Buyer, and Supplier shall not be required to commence delivery of such Product until the passage of such additional time.
(c) Supplier shall be required to accommodate any change of, or additions to, the Specifications for any Product, if and only if (i) in Supplier’s good faith judgment, such changed or additional Specifications would not require Supplier to violate good manufacturing practice, (ii) the representation and warranty of Buyer deemed made pursuant to Subsection (e) below is true and correct, and (iii) Buyer agrees to reimburse Supplier for the incremental costs and expenses incurred by Supplier in accommodating the changed or additional Specifications, including the costs of acquiring any new machinery and tooling. For the avoidance of doubt, such costs and expenses shall be payable by Buyer separately from the cost of Products at such time or times as Supplier shall request.
(d) Supplier shall notify Buyer in writing within thirty (30) days of its receipt of any request for changed or additional Specifications (i) whether Supplier will honor such changed or additional Specifications, (ii) if Supplier declines to honor such changed or additional Specifications, the basis therefor and (iii) if applicable, the estimated costs and expenses that Buyer will be required to reimburse Supplier in respect of the requested changes or additions, as provided in Subsection (c) above. Buyer shall notify Supplier in writing within fifteen (15) days after receiving notice of any required reimbursement whether Buyer agrees to assume such reimbursement obligation.
(e) By its request for any changed or additional Specifications for any Product, Buyer shall be deemed to represent and warrant to Supplier that the manufacture and sale of the Product incorporating Buyer’s changed or additional Specifications, as a result of such incorporation, will not and could not reasonably be expected to (i) violate or conflict with any contract, agreement, arrangement or understanding to which Buyer and/or any of its Affiliates is a party, including this Agreement and any other contract, agreement, arrangement or understanding with Supplier and/or its Affiliates, (ii) infringe on any trademark, service xxxx, copyright, patent, trade secret or other intellectual property rights of any Person, or (iii) violate any Applicable Law. Buyer shall indemnify and hold Supplier and its Affiliates harmless (including with respect to reasonable attorneys’ fees and disbursements) from any breach of this representation and warranty.
Marketing Materials (a) During the term of this Agreement, the Sub-Adviser agrees to furnish the Manager at its principal office for prior review and approval by the Manager all written and/or printed materials, including but not limited to, PowerPointÒ or slide presentations, news releases, advertisements, brochures, fact sheets and other promotional, informational or marketing materials (the “Marketing Materials”) for internal use or public dissemination, that are produced or are for use or reference by the Sub-Adviser, its affiliates or other designees, broker-dealers or the public in connection with the Series, and Sub-Adviser shall not use any such materials if the Manager reasonably objects in writing within five business days (or such other period as may be mutually agreed) after receipt thereof. Marketing Materials may be furnished to the Manager by first class or overnight mail, facsimile transmission equipment, electronic delivery or hand delivery.
(b) During the term of this Agreement, the Manager agrees to furnish the Sub-Adviser at its principal office all prospectuses, proxy statements, reports to shareholders, or Marketing Materials prepared for distribution to shareholders of each Series, or the public that refer to the Sub-Adviser in any way, prior to the use thereof, and the Manager shall not use any such materials if the Sub-Adviser reasonably objects in writing within five business days (or such other period as may be mutually agreed) after receipt thereof. The Sub-Adviser’s right to object to such materials is limited to the portions of such materials that expressly relate to the Sub-Adviser, its services and its clients. The Manager agrees to use its reasonable best efforts to ensure that materials prepared by its employees or agents or its affiliates that refer to the Sub-Adviser or its clients in any way are consistent with those materials previously approved by the Sub-Adviser as referenced in the first sentence of this paragraph. Marketing Materials may be furnished to the Sub-Adviser by first class or overnight mail, facsimile transmission equipment, electronic delivery or hand delivery.
Specifications That part of the Contract Documents consisting of written requirements for materials, equipment, systems, standards, and workmanship as applied to the Work, and certain administrative requirements and procedural matters applicable thereto. The term "Specifications" shall also include all written matter in the Project Manual or on the drawings and any Addenda or Change Orders thereto.
