Pressure Switches Sample Clauses

Pressure Switches. Pressure sensing switches for alarm and shutdown shall have separate housings. Switch contacts shall be rated at 125-V ac, 10A resistive and 125-V dc 0.5A resistive. Switch contacts shall have separate terminals. Alarm -------------------------------------------------------------------------------- EPC - Exhibit B -------------------- TENASKA GEORGIA GENERATION PROJECT Page 126 of 132 -------------------------------------------------------------------------------- switches shall close to alarm. Switches used for shutdown and control shall close to cause desired action. Switches shall be snap-acting type. All wetted parts shall be Series 300 stainless steel. Pressure connections shall be 1/2-inch FNPT. Alarm and shutdown switch settings shall not be adjustable from outside the housing. Instruments and controls shall be installed with suitable isolation valves to permit removal while the system is in operation.
AutoNDA by SimpleDocs
Pressure Switches. The Contractor removes all old pressure switches from the polyelectrolyte dosing system and disposes of them according to the Employer’s waste management procedure.  The Contractor supplies and installs new pressure switches on the polyelectrolyte dosing system using existing power and signal output cables, including new gaskets, spacers, brackets, bolts, nuts and washers etc., where required, after which the Contractor calibrates and performs the signal loop checks on them.  The Contractor supplies all relevant datasheets, conformance certificates, calibration certificates and final inspection reports.  Specifications: o Quantity: One (1) o Type: ASCO TriPoint Fixed Differential Pressure Switch o Datasheet: Polymer Equipment - Pressure Switches o KKS List: 07-00GDK40CP301 POT TO POLY DIL TNK PRESS SW 0.66/19646
Pressure Switches. The Contractor removes all old pressure switches from plant and disposes of them according to the Employer’s waste management procedure.  The Contractor supplies and installs new pressure switches using existing power and signal output cables, after which the Contractor calibrates and performs the signal loop checks on them.  The Contractor supplies all relevant datasheets, conformance certificates, calibration certificates and final inspections reports.  Specifications: o Quantity: Six (6)
Pressure Switches. Direct mounted pressure switches shall be used only for fire detection circuits and in Package units. For main plant applications, pressure transmitter with alarm card or receiver switch shall be used. Switches shall have internally accessible adjustments for set point. Pressure switches shall have fixed differential. Adjusters shall be provided with scales. Contacts shall be single pole double throw, except where double pole double throw snap acting are available and suitable. Cases shall meet electrical classification of the area where located.

Related to Pressure Switches

  • Tandem Switching 4.5.1 The Tandem Switching capability Network Element is defined as: (i) trunk-connect facilities, which include, but are not limited to, the connection between trunk termination at a cross-connect panel and switch trunk card; (ii) the basic switch trunk function of connecting trunks to trunks; and (iii) the functions that are centralized in the Tandem Switches (as distinguished from separate end office switches), including but not limited to call recording, the routing of calls to operator services and signaling conversion features. 4.5.2 Where <<customer_short_name>> utilizes portions of the BellSouth network in originating or terminating traffic, the Tandem Switching rates are applied in call scenarios where the Tandem Switching Network Element has been utilized. Because switch recordings cannot accurately indicate on a per call basis when the Tandem Switching Network Element has been utilized for an interoffice call originating from a UNE port and terminating to a BellSouth, Independent Company or Facility-Based CLEC office, BellSouth has developed, based upon call studies, a melded rate that takes into account the average percentage of calls that utilize Tandem Switching in these scenarios. BellSouth shall apply the melded Tandem Switching rate for every call in these scenarios. BellSouth shall utilize the melded Tandem Switching Rate until BellSouth has the capability to measure actual Tandem Switch usage in each call scenario specifically mentioned above, at which point the rate for the actual Tandem Switch usage shall apply. The UNE Local Call Flows set forth on BellSouth's website, as amended from time to time and incorporated herein by this reference, illustrate when the full or melded Tandem Switching rates apply for specific scenarios.

  • Switching All of the negotiated rates, terms and conditions set forth in this Section pertain to the provision of local and tandem switching.

  • Radios The Contractor or its employees shall not use any of the two-way radios or special telecommunications equipment under any circumstances. No exceptions will be made to this rule. Violation is grounds for immediate termination of this Contract, as well as punitive action.

  • Local Switching 4.1.1 BellSouth shall provide non-discriminatory access to local circuit switching capability, and local tandem switching capability, on an unbundled basis, except as set forth below in Section 4.1.

  • Workstation/Laptop encryption All workstations and laptops that process and/or store DHCS PHI or PI must be encrypted using a FIPS 140-2 certified algorithm which is 128bit or higher, such as Advanced Encryption Standard (AES). The encryption solution must be full disk unless approved by the DHCS Information Security Office.

  • Electrical Provide drawings for the following systems: .1 Lighting including circuiting and luminaire identification and switching. Also provide illuminance computer printout for all indoor typical indoor spaces and parking lots. .2 Convenience outlets and circuiting, special outlets and circuiting, television outlets, and power systems and equipment. Provide riser diagrams for all electrical systems including master clock, intercom, fire alarm, ITV, computer networking/telephone. Also, provide for emergency and normal power distribution. Provide luminaire schedule. .3 Panel schedule may be in preliminary form but circuitry must be included. .4 Applicable installation details. .5 General legend and list of abbreviations. .6 Voltage drop computation for all main feeders. .7 Short circuit analysis .8 Provide 1/2" scale floor plan and wall elevations for all electrical rooms.

  • Lighting A system of fixtures providing or controlling the light sources used on or near the airport or within the airport buildings. The field lighting includes all luminous signals, markers, floodlights, and illuminating devices used on or near the airport or to aid in the operation of aircraft landing at, taking off from, or taxiing on the airport surface.

  • Pipelines Developer shall have no interest in the pipeline gathering system, which gathering system shall remain the sole property of Operator or its Affiliates and shall be maintained at their sole cost and expense.

  • Sprinkler System If there now is or shall be installed in said building a "sprinkler system" the Tenant agrees to keep the appliances thereto in the demised premises in repair and good working condition, and if the New York Board of Fire Underwriters or the New York Fire Insurance Exchange or any bureau, department or official of the State or local government requires or recommends that any changes, modifications, alterations or additional sprinkler heads or other equipment be made or supplied by reason of the Tenant's business, or the location of partitions, trade fixtures, or other contents of the demised premises, or if such changes, modifications, alterations, additional sprinkler heads or other equipment in the demised premises are necessary to prevent the imposition of a penalty or charge against the full allowance for a sprinkler system in the fire insurance rate as fixed by said Exchange or by any fire insurance company, the Tenant will at the Tenant's own expense, promptly make and supply such changes, modifications, alterations, additional sprinkler head or other equipment. As additional rent hereunder the Tenant will pay to the Landlord, annually in advance, throughout the term 100%, toward the contract price for sprinkler supervisory service.

  • Moonlighting Employment as a physician in a professional capacity outside of what is outlined in this Agreement, whether temporary special medical activity (“TSMA”) or external moonlighting, must be approved in writing, in advance, by the Departmental Chair, Program Director and Director of Graduate Medical Education (or designee). Even if approved, professional and general liability insurance as outlined in Section 5.4 is not provided to Trainee engaged in external moonlighting. Trainee acknowledges he or she has the responsibility to obtain insurance for such engagement. TSMA and external moonlighting must be included and reported as part of Trainee's hours spent on clinical experience and education. Trainee shall not be required to engage in any outside work.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!