Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ASTM A36 Standard for Carbon Structural Steel ASTM A153 Standard for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM A193 Standard for Alloy-Steel and Stainless Steel Bolting Materials for High- Temperature Service ASTM A194 Standard for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High- Temperature Service, or Both ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A320 Standard for Alloy Steel Bolting Materials for Low Temperature Service ASTM A563 Standard for Carbon and Alloy Steel Nuts ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings ASTM B695 Standard for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain (Flat), Unhardened for General Use ASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete Elements May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 - 2 ANCHORAGE TO CONCRETE
Appears in 1 contract
Samples: Contract
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ANSI/AWWA C111/A21 Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings ANSI/AWWA C906 Polyethylene (PE) Pressure Pipe and Fittings, 4-inch through 63-inch, for Water Distribution AWWA Manual M55 PE Pipe - Design and Installation. ASTM A36 A276 Stainless Steel Bars and Shapes ASTM D2321 Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications ASTM D2657 Heat Joining Polyolefin Pipe and Fittings ASTM D3350 Polyethylene Plastics Pipe and Fittings Material ASTM A193/A193M Standard for Carbon Structural Steel ASTM A153 Standard for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM A193 Standard Specification for Alloy-Steel and Stainless Steel Bolting Materials for High- High Temperature or High Pressure Service and Other Special Purpose Applications ASTM A194 A194/A194M Standard Specification for Carbon and Alloy Steel Nuts for Bolts for High-High Pressure and High- or High Temperature Service, or Both ASTM A307 A240/A240M Standard Specification for Carbon Chromium and Chromium-Nickel Stainless Steel Bolts Plate, Sheet, and Studs, 60,000 PSI Tensile Strength Strip for Pressure Vessels and for General Applications ASTM A320 Standard for Alloy Steel Bolting Materials for Low Temperature Service ASTM A563 Standard for Carbon and Alloy Steel Nuts ASTM A780 F2164 Standard Practice for Repair Field Leak Testing of Damaged Polyethylene (PE) Pressure Piping Systems Using Hydrostatic Pressure ASTM F2620 Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Uncoated Areas Fittings Plastics Pipe Institute (PPI): Handbook of Hot-Dip Galvanized Coatings ASTM B695 Standard Polyethylene Pipe
a. Technical Note 38, Bolt Torque for Coatings Polyethylene Flanged Joints.
b. TR-33, Generic Butt Fusion Joining Procedure for Field Joining of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain (Flat), Unhardened for General Use ASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete Elements Plastic Pipe: Qualifying Persons to Make Joints May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 15065 - 2 ANCHORAGE TO CONCRETEHIGH DENSITY POLYETHYLENE PIPE
B. Affidavit of Compliance:
1. The manufacturer shall furnish an affidavit of compliance conforming to the requirements of AWWA C906, Section 1.5, affirming that the piping components comply with the requirements of AWWA C906 and this Section.
2. The affidavit shall be signed under penalty of perjury by an officer of the pipe manufacturer's company.
Appears in 1 contract
Samples: Contract
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ASTM A36 Standard C1173 Flexible Transition Couplings for Carbon Structural Steel Underground Piping Systems ASTM A153 Standard D1248 Polyethylene Plastics Extrusion Materials For Wire and Cable ASTM D1784 Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds ASTM D1785 Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 ASTM D4101 Polypropylene Injection and Extrusion Materials ASTM D2241 Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) ASTM D2464 Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 ASTM D2466 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 ASTM D2467 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 ASTM D2513 Polyethylene (PE) Gas Pressure Pipe, Tubing, and Fittings ASTM D2564 Solvent Cements for Zinc Coating Poly(Vinyl Chloride) (HotPVC) Plastic Piping Systems ASTM D2665 Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings ASTM D 2683 Socket-DipType Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing ASTM D2657 Heat Fusion Joining of Polyolefin Pipe and Fittings ASTM D3034 Type PSM Poly(Vinyl Chloride) on Iron (PVC) Sewer Pipe and Steel Hardware Fittings ASTM A193 Standard D3261 Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Alloy-Steel Polyethylene (PE) Plastic Pipe and Stainless Steel Bolting Tubing ASTM D3350 Polyethylene Plastics Pipe and Fittings Materials ASTM D4101 Polypropylene Injection and Extrusion Materials ASTM D5926 (PVC) Gaskets for High- Temperature Service ASTM A194 Standard for Carbon Drain, Waste, and Alloy Steel Nuts for Bolts for High-Pressure and High- Temperature Service, or Both ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A320 Standard for Alloy Steel Bolting Materials for Low Temperature Service ASTM A563 Standard for Carbon and Alloy Steel Nuts ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings ASTM B695 Standard for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain Vent (FlatDWV), Unhardened for General Use ASTM F1554 Standard Specification for Anchor BoltsSewer, Steel, 36, 55Sanitary, and 105Storm Plumbing Systems ASTM F402 Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings ASTM F437 Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 ASTM F438 Socket-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40 ASTM F439 Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80 ASTM F441 Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 ASTM F477 Elastomeric Seals (Gaskets) for Joining Plastic Pipe CSA B602 Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria Coupling for Post-Installed Adhesive Anchors in Concrete Elements Drain, Waste, Vent Pipe, and Sewer Pipe May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 15064 - 2 ANCHORAGE TO CONCRETEPLASTIC PIPING
Appears in 1 contract
Samples: Contract
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ANSI B16.11 Forged Steel Fittings, Socket-Welding and Threaded ASME A13.1 Scheme for the Identification of Piping Systems ASME B1.
20.1 Pipe Threads, General Purpose ASME B16.3 Malleable-Iron Threaded Fittings Class 150 and 300 ASME B16.5 Pipe Flanges and Flanged Fittings, NPS 1/2 – NPS 24 ASME B16.22 Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings ASME B31.3 Process Piping ASME B31.9 Building Services Piping ASTM A36 Standard for Carbon Structural Steel ASTM A153 Standard for Zinc Coating (A53 Pipe, Steel, Black and Hot-Dip) on Dipped Zinc-Coated, Welded and Seamless ASTM A74 Cast Iron Soil Pipe and Fittings ASTM A105 Forgings, Carbon Steel, for Piping Applications ASTM A106 Seamless Carbon Steel Hardware ASTM A193 Standard Pipe for AlloyHigh-Steel and Stainless Steel Bolting Materials for High- Temperature Service ASTM A194 Standard for A197 Cupola Malleable Iron ASTM A234 Piping Fittings of Wrought Carbon Steel and Alloy Steel Nuts for Bolts for High-Pressure Moderate and High- Temperature Service, or Both ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength ASTM A320 Standard for Alloy Steel Bolting Materials for Low High Temperature Service ASTM A563 Standard A312 Seamless and Welded Austenitic Stainless Steel Pipes ASTM A403 Wrought Austenitic Stainless Steel Piping Fittings ASTM A888 Hubless Cast Iron Soil Pipe and Fittings for Carbon Sanitary and Alloy Steel Nuts Storm Drain, Waste, and Vent Piping Applications ASTM A780 Standard Practice B88 Seamless Copper Water Tube ASTM C1173 Flexible Transition Couplings for Repair of Damaged Underground Piping Systems ASTM D1784 Rigid Poly (Vinyl Chloride) (PVC) Compounds and Uncoated Areas of HotChlorinated Poly (Vinyl Chloride) (CPVC) Compounds ASTM D1785 Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120 ASTM D2466 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 ASTM D2467 Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 ASTM D3139 Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals ASTM D3262 “Fiberglass” (Glass-Dip Galvanized Coatings ASTM B695 Standard for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for EpoxyFiber-Reinforced Thermosetting-Resin) Sewer Pipe ASTM D3517 “Fiberglass” (Glass-Base Bonding Systems Fiber-Reinforced Thermosetting-Resin) Pressure Pipe ASTM D5926 Poly (Vinyl Chloride) (PVC) Gaskets for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics Drain, Waste, and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain Vent (FlatDWV), Unhardened for General Use ASTM F1554 Standard Specification for Anchor BoltsSewer, Steel, 36, 55Sanitary, and 105Storm Plumbing Systems ASTM F441 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80 ASTM F477 Elastomeric Seals (Gaskets) for Joining Plastic Pipe AWWA C111 Rubber-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria Gasket Joints for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for PostDuctile-Installed Adhesive Anchors in Concrete Elements Iron Pressure Pipe and Fittings May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 15050 - 2 ANCHORAGE TO CONCRETEPIPING SYSTEMS Reference Title AWWA C151 Ductile-Iron Pipe, Centrifugally Cast for Water or Other Liquids AWWA C200 Steel Water Pipe - 6 Inches and Larger AWWA C207 Steel Pipe Flanges for Waterworks Service - Sizes 4 In. Through 144 In. AWWA C208 Dimensions for Fabricated Steel Water Pipe Fittings AWWA C509 Resilient-Seated Gate Valves for Water Supply Service AWWA C600 Installation of Ductile-Iron Water Mains and Their Appurtenances AWWA C651 Disinfecting Water Mains CISPI 301 Specification Data for Hubless Cast Iron Sanitary System with No-Hub Pipe and Fittings CISPI 310 Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Application. EPA SDWA Section 1417(d) Reduction of Lead in Drinking Water Act Requirements, Amendments to Safe Drinking Water Act (SDWA), effective January 4, 2014 MIL-H-13528B Hydrochloric Acid, Inhibited, Rust Removing MIL-STD-810 Environmental Engineering Considerations and Laboratory Tests XXXX XX-0169 Control of External Corrosion on Underground or Submerged Metallic Piping Systems XXXX XX-0286 Electrical Isolation of Cathodically Protected Pipelines NFPA 13 Installation of Sprinkler Systems NSF/ANSI Health effects criteria (Lead Content Compliance) for water system components Standard 61 NSF/ANSI Standard 372 Lead Content Compliance Guidelines for water system components UPC Uniform Plumbing Code
Appears in 1 contract
Samples: Contract
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title AISC 348 Specification for Structural Joints using Using High-Strength Bolts AISC 303 Code of Standard Practice for Steel Buildings and Bridges, excluding Sections 3, 4, 7.2, 7.11.3, 4, 7.11.4 and 7.11.5 AISC 206 Erector Certification Program AISC 325 Steel Construction Manual AISC Quality Certification Program AISC 360 Specification for Structural Steel Buildings ASTM A6 Standard Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Steel Piling ASTM A36 Standard Specification for Carbon Structural Steel ASTM A53 Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless ASTM A123 Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products ASTM A143 Standard Practice for Safeguarding Against Embrittlement of Hot-Dip Galvanized Structural Steel Products and Procedures for Detecting Embrittlement ASTM A153 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM A193 A325 Standard for Alloy-Steel and Stainless Steel Bolting Materials for High- Temperature Service ASTM A194 Standard for Carbon and Alloy Steel Nuts for Bolts Specification for High-Pressure Strength Bolts for Structural Steel Joints ASTM A384 Standard Practice for Safeguarding Against Warpage and High- Temperature ServiceDistortion During Hot- Dip Galvanizing of Steel Assemblies ASTM A385 Standard Practice for Providing High-Quality Zinc Coatings (Hot-Dip) ASTM A490 Standard Specification for Heat-Treated Steel Structural bolts, or Both ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI 150 ksi Minimum Tensile Strength ASTM A320 A500 Standard Specification for Alloy Cold-Formed Welded and Seamless Carbon Steel Bolting Materials for Low Temperature Service Structural Tubing in Rounds and Shapes ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings ASTM A992 Standard Specification for Steel for Structural Shapes for Use in Building Frames ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain (Flat), Unhardened for General Use ASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete Elements May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 05120 - 2 ANCHORAGE TO CONCRETESTRUCTURAL STEEL
Appears in 1 contract
Samples: Contract
Referenced Standards. This Section incorporates by reference the latest revision of the following documents. These references are a part of this Section as specified and modified. In case of conflict between the requirements of this Section and those of the listed documents, the requirements of this Section shall prevail. Reference Title ANSI/NAAMM MBG 531 Metal Bar Grating Manual ASME Section V Boiler and Pressure Vessel Code : Nondestructive Examination ASME Section IX Boiler and Pressure Vessel Code: Welding and Brazing Qualifications ASTM A29 General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought ASTM A36 Standard for Carbon Structural Steel ASTM A53 Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless ASTM A123 Zinc (Hot-Dip Galvanize) Coatings on Iron and Steel Products ASTM A153 Standard for Zinc Coating (Hot-Dip) on Iron and Steel Hardware ASTM A167 Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip ASTM A193 Standard for Alloy-Steel and Stainless Steel Bolting Materials for High- High-Temperature Service ASTM A194 Standard for Carbon and Alloy Steel Nuts for Bolts for High-Pressure and High- Temperature Service, or Both ASTM A240 Heat-Resisting Chromium-Nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels ASTM A242 High-Strength Low-Alloy Structural Steel ASTM A276 Stainless Steel Bars and Shapes ASTM A307 Standard for Carbon Steel Bolts and Studs, 60,000 PSI psi Tensile Strength ASTM A312 Seamless and Welded Austenitic Stainless steel Pipes ASTM A320 Standard for Alloy Steel Bolting Materials for Low Temperature Service ASTM A325 Structural Bolt, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength ASTM A479 Stainless Steel Bars and Shapes for Pressure Vessels ASTM A496 Steel Wire, Deformed, for Concrete Reinforcement ASTM A500 Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes ASTM A563 Standard for Carbon and Alloy Steel Nuts ASTM A588 High-Strength Low-Alloy Structural Steel, up to 50 Ksi [345 MPa] Minumum Yield Point, with Atmospheric Corrosion Resistance May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05500 - 2 METAL FABRICATIONS Reference Title ASTM A606 Steel, Sheet and Strip, High-Strength, Low-Alloy, Hot-rolled and Cold-Rolled, with Improved Atmospheric Corrosion Resistence ASTM A615 Deformed and Plain Billet-Steel Bars for Concrete Reinforcement ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings ASTM A786 Rolled Steel Floor Plates ASTM A793 Rolled Floor Plate, Stainless Steel ASTM A847 Cold-Formed Welded and Seamless High-Strength, Low Alloy Structural Tubing with Improved Atmospheric Corrosion Resistance ASTM B209 Aluminum and Aluminum-Alloy Sheet and Plate ASTM B210 Aluminum and Aluminum-Alloy Drawn Seamless Tubes ASTM B211 Aluminum and Aluminum-Alloy Bar, Rod, and Wire ASTM B221 Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes ASTM B241 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube ASTM B308 Aluminum-Alloy 6061-T6 Standard Structural Profiles ASTM B632 Aluminum-Alloy Rolled Tread Plate ASTM B695 Standard for Coatings of Zinc Mechanically Deposited on Iron and Steel ASTM C881 Standard for Epoxy-Resin-Base Bonding Systems for Concrete ASTM C882 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete by Slant Shear ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position ASTM D695 Standard Test Method for Compressive Properties of Rigid Plastics ASTM D746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique ASTM D1525 Standard Test Method for Vicat Softening Temperature of Plastics ASTM F436 Standard Specification for Hardened Steel Washers ASTM F844 Standard for Washers, Steel, Plain (Flat), Unhardened for General Use ASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength SSPC SP-1 Solvent Cleaning SSPC SP-2 Hand Tool Cleaning SSPC SP-3 Power Tool Cleaning AC193 Acceptance Criteria for Mechanical Anchors in Concrete Elements AC308 Acceptance Criteria for Post-Installed Adhesive Anchors in Concrete Elements May 2017 C01025C17 Georgetown Wet Weather Treatment Station 05501 - 2 ANCHORAGE TO CONCRETESSPS SP-5 White Metal Blast Cleaning
Appears in 1 contract
Samples: Contract
