REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.
Contractor’s Equipment Payment for required equipment owned by the Construction Manager or an affiliate of the Construction Manager will be based solely on an hourly rate derived by dividing the current appropriate monthly rate by 176 hours. No payment will be made under any circumstances for repair costs, freight and transportation charges, fuel, lubricants, insurance, any other costs and expenses, or overhead and profit. Payment for such equipment made idle by delays attributable to the Government will be based on one-half the derived hourly rate under this subsection.
Spare Parts 14.1 As specified, the supplier may be required to provide any or all of the following materials, notifications, and information pertaining to spare parts manufactured or distributed by the supplier:
(a) such spare parts as the purchaser may elect to purchase from the supplier, provided that this election shall not relieve the supplier of any warranty obligations under the contract and;
(b) In the event of termination of production of the spare parts:
(i) advance notification to the purchaser of the pending termination, in sufficient time to permit the purchaser to procure needed requirements and;
(ii) Following such termination, furnishing at no cost to the purchaser, the blueprints, drawings, and specifications of the spare parts, if requested.
ESTIMATED / SPECIFIC QUANTITY CONTRACTS Estimated quantity contracts, also referred to as indefinite delivery / indefinite quantity contracts, are expressly agreed and understood to be made for only the quantities, if any, actually ordered during the Contract term. No guarantee of any quantity is implied or given. With respect to any specific quantity stated in the contract, the Commissioner reserves the right after award to order up to 20% more or less (rounded to the next highest whole number) than the specific quantities called for in the Contract. Notwithstanding the foregoing, the Commissioner may purchase greater or lesser percentages of Contract quantities should the Commissioner and Contractor so agree. Such agreement may include an equitable price adjustment.
Accessories, Spare Parts and Tools Accessories, spare parts and tools dispatched with a piece of equipment, machine, apparatus or vehicle, which are part of the normal equipment and included in the price thereof or which are not separately invoiced, shall be regarded as one with the piece of equipment, machine, apparatus or vehicle in question.
Shipment Dell will ship the APEX System to the Site when included as part of the APEX Service. The terms and process for shipment and delivery of the APEX System will be stated in the applicable Service Offering Description.
Repair or Replacement Except where an appraisal has been made, the Insurer, instead of making payment, may, within a reasonable time, repair, rebuild or replace the property damaged or lost with other of like kind and quality if, within seven days after the receipt of the proof of loss, it gives written notice of its intention to do so.
Repair (a) Tenant, at its sole cost and expense, shall take good care of the Premises, including all building equipment and systems located therein and serving the Premises. Tenant shall make all repairs, interior or exterior, structural or otherwise, as and when needed, to preserve the Premises, the need for which repair arises out of (i) the performance or existence of any Alteration to the Premises made by Tenant, (ii) the installation or operation of Tenant's property or fixtures, and the movement of same in or about the Premises or the Building, (iii) the acts, failures to act or negligence of Tenant or Tenant's servants, employees, contractors, agents, visitors or licensees, or (iv) the use, of the Premises by Tenant or Tenant's servants, employees, contractors, agents, visitors or licensees. Landlord shall not be liable for and, except as provided in Paragraph 20, there shall be no abatement of Rent with respect to any injury to or interference with Tenant's business arising from any repairs, maintenance, alteration or interruption of services in or to any portion of the Office Park or Building, including the Premises, or to the fixtures, appurtenances and equipment therein.
(b) All repairs and replacements made by or on behalf of Tenant shall be made and performed in a workmanlike manner (i) at Tenant's cost and expense and at such time and in such manner as Landlord may designate, (ii) by contractors approved by Landlord, (iii) such work shall be at least equal in quality, value, and utility to the original work or installation, and (iv) in accordance with the Rules and Regulations for the Building adopted by Landlord from time to time and in accordance with all applicable laws and regulations of governmental authorities having jurisdiction over the Premises. If Tenant shall fail after 10 days' notice by Landlord to proceed with due diligence to make repairs required to be made by Tenant, Landlord may make the repairs at the expense of Tenant and the expenses thereof incurred by Landlord shall be reimbursed immediately as Additional Rent after submission of a xxxx or statement there for.
Spares Boeing will revise, as applicable, the customized Recommended Spares Parts List (RSPL) and Illustrated Parts Catalog (IPC).
Packing Materials and Containers for Shipment Packing materials and containers in which the good is packed for shipment shall be disregarded in determining whether--
(i) the non-originating materials used in the production of the good undergo an applicable change in tariff classification set out in subdivision (t) of this note; and
(ii) the good satisfies a regional value-content requirement.
