ACCEPTANCE OF DEFECTIVE OR NON-CONFORMING WORK 13.3.1 The State may accept defective or nonconforming Work pursuant to Paragraph 13.2.1
Non-Conforming Product (a) In the event Patheon discovers a potential Non-Conforming Product prior to delivery of such Product to Flexion, Patheon shall provide written notice to Flexion as soon as practicable describing in detail the Non-Conforming Product and the potential cause of such Non-Conforming Product. Flexion (or its shipping carrier) will perform a customary inspection of the Products Manufactured by Patheon on receipt. For the avoidance of doubt, such inspection will be limited to a visual inspection of the shipment-ready packaged Products (and associated shipping documentation) and Flexion will not be obliged to perform any testing of the Product. Flexion shall within (i) […***…] days after delivery thereof by Patheon or (ii) within […***…] days after Flexion discovers or is informed of a discovery of nonconformity that could not reasonably have been detected by the customary inspection on delivery (but not after the expiration date of the Product), give Patheon notice of any Non-Conforming Product (including a sample of such Non-Conforming Product, if applicable) (a “Deficiency Notice”). Subject to Flexion’s rights under 3.10 and 3.12, should Flexion fail to give Patheon the Deficiency Notice within the applicable […***…] day period, then the delivery will be deemed to have been accepted by Flexion on the […***…] day after delivery or discovery, as applicable. Patheon shall have no liability under this Section 2.8 for Nonconforming Product for which it has not received a Deficiency Notice within such applicable […***…] day period.
(b) Patheon shall conduct a root-cause analysis to verify whether a Product constitutes a Non-Conforming Product and, if found, to determine the cause of such Non-Conforming Product (including by undertaking an appropriate evaluation of a Non-Conforming Product sample, as applicable). Flexion shall provide reasonable cooperation to Patheon in connection with any such root-cause analysis. Patheon shall notify Flexion in writing of its determination regarding whether the Product constitutes a Non-Conforming Product within […***…] days after either discovery of the Non-Conforming Product or receipt of such Deficiency Notice from Flexion, as applicable. Such notification shall include Patheon’s good faith determination of the cause of the Non-Conforming Product.
ACCEPTANCE OF NONCONFORMING WORK If the Owner prefers to accept Work that is not in accordance with the requirements of the Contract Documents, the Owner may do so instead of requiring its removal and correction, in which case the Contract Sum will be reduced as appropriate and equitable. Such adjustment shall be effected whether or not final payment has been made.
Right to Refuse Unsafe Work Employees have the right to refuse to perform unsafe work pursuant to the Occupational Health and Safety Regulations of the Workers Compensation Act.
Right to Refuse Dangerous Work An employee shall have the right to refuse to work in dangerous situations.
Inspection and Rejection of Nonconforming Goods The Buyer has the right to inspect the Goods on or after the Delivery Date. Buyer, at its sole option, may inspect all or a sample of the Goods, and may reject all or any portion of the Goods if it determines the Goods are nonconforming or defective. If Buyer rejects any portion of the Goods, Buyer has the right, effective upon written notice to Seller, to: (a) rescind the Order in its entirety; (b) accept the Goods at a reasonably reduced price; or (c) reject the Goods and require replacement of the rejected Goods. If Buyer requires replacement of the Goods, Seller shall, at its expense, promptly replace the nonconforming Goods and pay for all related expenses, including, but not limited to, transportation charges for the return of the defective goods and the delivery of replacement Goods. If Seller fails to timely deliver replacement Goods, Buyer may replace them with goods from a third party and charge Seller the cost thereof and terminate this Order for cause pursuant to Section 19. Any inspection or other action by Buyer under this Section shall not reduce or otherwise affect Seller's obligations under the Order, and Buyer shall have the right to conduct further inspections after Seller has carried out its remedial actions.
Right to Reject The Department reserves the right to accept or reject all proposals, or separable portions thereof, and to waive any minor irregularity, technicality, or omission if the Department determines that doing so shall serve the Department’s best interests. The Department may reject any proposal not submitted in the manner specified by the solicitation documents.
Nonconforming Work 5.6.1 Rejection, Removal and Replacement of Nonconforming Work
Non-Conforming Measures 1. Articles 2, 3 and 6 shall not apply to:
(a) any existing non-conforming measure that is Maintained by the following, as set out in the Schedule of each Contracting Party in Annex I:
(i) the central government of a Contracting Party; or
(ii) a prefecture of Japan or a province or a Municipality of the Republic of Mozambique;
(b) any existing non-conforming measure that is maintained by a local government other than a prefecture and a province and a municipality referred to in subparagraph (a)(ii);
(c) the continuation or prompt renewal of any nonconforming measure referred to in subparagraphs
(a) and (b); or
(d) an amendment or modification to any nonconforming measure referred to in subparagraphs
(a) and (b), provided that the amendment or modification does not decrease the conformity of the measure as it existed immediately before the amendment or modification with Articles 2, 3 and 6.
2. Articles 2, 3 and 6 shall not apply to any measure that a Contracting Party adopts or maintains with respect to sectors, sub-sectors or activities set out in its Schedule in Annex II.
3. Neither Contracting Party shall, under any measure adopted after the date of entry into force of this Agreement and covered by its Schedule in Annex II, require an investor of the other Contracting Party, by reason of its nationality, to sell or otherwise dispose of an investment that exists at the time when the measure becomes effective.
4. In cases where a Contracting Party makes an amendment or a modification to any existing non-conforming measure set out in its Schedule in Annex I or where a Contracting Party adopts any new or more restrictive measure with respect to sectors, sub-sectors, or activities set out in its Schedule in Annex II after the date of entry into force of this Agreement, the Contracting Party shall, prior to the implementation of the amendment or modification or the new or more restrictive measure, or in exceptional circumstances, as soon as possible thereafter:
(a) notify the other Contracting Party of detailed information on such amendment or modification, or such measure; and
(b) hold, upon request by the other Contracting Party, consultations in good faith with the other Contracting Party with a view to achieving mutual satisfaction.
5. Each Contracting Party shall endeavour, where appropriate, to reduce or eliminate the non-conforming measures specified in its Schedules in Annexes I and II respectively.
6. Articles 2, 3 and 6 shall not apply to any measure covered by the exceptions to, or derogations from, obligations under Articles 3 and 4 of the TRIPS Agreement, as specifically provided in Articles 3 through 5 of the TRIPS Agreement.
7. Articles 2, 3 and 6 shall not apply to any measure that a Contracting Party adopts or maintains with respect to government procurement.
Rejection of Work Using the Notice of Non-Conforming Work procedures outlined in the General Conditions, the Design Professional shall reject work that does not comply with the requirements of the Contract Documents or that does not comply with the applicable laws and codes. The Design Professional shall have authority to order testing of the Work, as is provided in the Contract Documents or as otherwise required in its judgment, whether such work is fabricated, installed, or completed.
