Safety, breakdowns and accidents 17.5.1 The Concessionaire shall ensure safe conditions for the Users and passengers, and in the event of unsafe conditions, it shall follow the relevant operating procedures and undertake removal of obstruction and debris without delay. Such procedures shall conform to the provisions of this Agreement, Applicable Laws, Applicable Permits and Good Industry Practice.
Trunk Group Architecture and Traffic Routing The Parties shall jointly engineer and configure Local/IntraLATA Trunks over the physical Interconnection arrangements as follows:
Safety Orientation All employees shall be certified in Safety Orientation. Safety Orientation shall consist of three parts: PART 1 - the CODC Interactive Rights and Responsibilities course; PART 2 - the XXXX course or equivalent, and PART 3 - Employer or Owner Project Specific Training. It is the responsibility of each employee to hold current certification and maintain certification in part 1 and Part 2. The Employer or Owner shall provide to each Employee before commencing work with PART 3 - Employer or Owner Project Specific Training. Each Employee shall be on the payroll and paid while receiving PART 3 training. As a condition of employment it is the sole responsibility of each and every employee to obtain, hold and maintain all current certification(s) in any and all legislated safety training requirements (i.e. WHMIS, Fall Arrest, etc.) that are trade specific. Supporting documentation of all legislated training must be provided by the employee to the Union prior to dispatch and to the employer upon hire and may be further requested by the employer at any time during the duration of their employment. Prior to the expiration of any certification, the Employer will notify the Employee of the pending expiration and give the Employee reasonable time to renew their certification. Further, prior to arriving at site, employees shall hold current qualification(s) for the specific tasks and equipment identified in the dispatch request. If the employee has to be trained after dispatch, all costs borne by the Employer shall be reimbursed by the Training Fund. The CODC Harassment Policy and Procedures, including the provisions regarding General Harassment and as amended from time to time shall be the minimum standard of this Agreement.
SAFETY AND ACCIDENT PREVENTION In performing work under this Contract on State premises, Contractor shall conform to any specific safety requirements contained in the Contract or as required by law or regulation. Contractor shall take any additional precautions as the State may reasonably require for safety and accident prevention purposes. Any violation of such rules and requirements, unless promptly corrected, shall be grounds for termination of this Contract in accordance with the default provisions hereof.
Safety Program The Contractor shall design a specific safety program for the Work for the site(s). The Contractor shall establish and require all Subcontractors to establish reasonable safety programs. The Contractor shall also submit its standard monthly safety reports to the Owner and Design Professional. No imposition of responsibility on the Contractor for safety under this Contract shall relieve any subcontractor of its responsibility for safety of persons or property on or near the Project Site. The Contractor shall include in his plant he names of the person in charge of Safety.
Safety Glasses 10.3.1 Where a teacher is considered to be working in an “eye danger” area, the teacher shall receive a personal issue of standard neutral safety glasses which shall remain the property of the employer.
Safety Issues The Tenant will procure that in the carrying out of the Building Improvement Plan:
Quality Management System Supplier hereby undertakes, warrants and confirms, and will ensue same for its subcontractors, to remain certified in accordance with ISO 9001 standard or equivalent. At any time during the term of this Agreement, the Supplier shall, if so instructed by ISR, provide evidence of such certifications. In any event, Supplier must notify ISR, in writing, in the event said certification is suspended and/or canceled and/or not continued.
CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.
Safety Shoes 3901 Employees who are required to wear steel-toed safety shoes will receive $200 toward the purchase and/or replacement of these shoes in the first quarter of each year. Any employee out on an authorized leave shall receive payment within thirty days of their return to paid duty. New employees who are required to wear steel- toed safety shoes will receive $200 toward the purchase of shoes in their first paycheck; for employees hired on or after December 1, he/she shall not receive an additional $200 in the following February.
