Section 1 - Union Label Sample Clauses

Section 1 - Union Label. It shall not be a violation of this Agreement for an employee to post the Teamsters' Union Label in a conspicuous place on the glass area of the equipment he is operating. The said label to be a size not in excess of three (3") by four inches (4") and not to be attached to any area which will impair the vision of the driver.
AutoNDA by SimpleDocs
Section 1 - Union Label. The Union Labels, as furnished by the Union, shall be placed upon all work manufactured, fabricated or built by members of the Sheet Metal Workers' Union by the Shop Xxxxxxx and such Union Labels shall be in the custody of the Shop Xxxxxxx. It shall not be considered a violation of this agreement in the event that a Shop Xxxxxxx fails to affix the Union Label. In addition there shall be placed upon such work the Employer's imprint.

Related to Section 1 - Union Label

  • Union Label Upon depletion of existing stocks, all uniforms and clothing issued by the Employer shall bear a recognized Union label.

  • Reactive Power and Primary Frequency Response 9.6.1 Power Factor Design Criteria

  • Transfer and Seniority Outside the Bargaining Unit (a) It is understood that an employee shall not be transferred by the Hospital to a position outside the bargaining unit without his consent except in the case of temporary assignments not exceeding six (6) months. Such employees on temporary assignments shall remain members of the bargaining unit.

  • Transfer and Seniority Outside Bargaining Unit No employee shall be transferred to a position outside the bargaining unit without his consent. If an employee is transferred to a position outside of the bargaining unit, he shall retain his seniority accumulated up to the date of leaving the unit, but will not accumulate any further seniority. If such an employee returns to the bargaining unit within twelve (12) months, he shall be placed in a job consistent with his seniority. Such return shall not result in the layoff or bumping of an employee holding greater seniority.

  • Increasing Seat Belt Use in the United States Pursuant to Executive Order 13043, 62 FR 19217 (Apr. 18, 1997), Recipient should encourage its contractors to adopt and enforce on-the- job seat belt policies and programs for their employees when operating company-owned, rented or personally owned vehicles.

  • GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.

  • CFR Part 200 or Federal Provision - Xxxx Anti-Lobbying Amendment - Continued If you answered "No, Vendor does not certify - Lobbying to Report" to the above attribute question, you must download, read, execute, and upload the attachment entitled "Disclosure of Lobbying Activities - Standard Form - LLL", as instructed, to report the lobbying activities you performed or paid others to perform. 2 CFR Part 200 or Federal Provision - Federal Rule Compliance with all applicable standards, orders, or requirements issued under section 306 of the Clean Air Act (42 U.S.C. 1857(h)), section 508 of the Clean Water Act (33 U.S.C. 1368), Executive Order 11738, and Environmental Protection Agency regulations (40 CFR part 15). (Contracts, subcontracts, and subgrants of amounts in excess of $100,000) Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, ESC Region 8 and TIPS Members requires the proposer certify that in performance of the contracts, subcontracts, and subgrants of amounts in excess of $250,000, the vendor will be in compliance with all applicable standards, orders, or requirements issued under section 306 of the Clean Air Act (42 U.S.C. 1857(h)), section 508 of the Clean Water Act (33 U.S.C. 1368), Executive Order 11738, and Environmental Protection Agency regulations (40 CFR part 15). Does vendor certify compliance? Yes

  • AIR FORCE FEDERAL ACQUISITION REGULATION SUPPLEMENT CONTRACT CLAUSES 5352.201-9101 OMBUDSMAN (APR 2014) Para (c). Ombudsmen names, addresses, phone numbers, fax, and email addresses. 'Xx. Xxxx Xxxxxxxxxx, AFLCMC/AQP, Phone: DSN 000-0000 Comm (000) 000-0000, E- mail: Xxxx.xxxxxxxxxxxxxxx.0@xx.xx.xxx.' 5352.223-9000 ELIMINATION OF USE OF CLASS I OZONE DEPLETING SUBSTANCES (ODS) (NOV 2012) 5352.223-9001 HEALTH AND SAFETY ON GOVERNMENT INSTALLATIONS (NOV 2012) 5352.242-9000 CONTRACTOR ACCESS TO AIR FORCE INSTALLATIONS (NOV 2012) Para (b), Any additional requirements to comply with local security procedures '"to be cited in each individual task order"' Para (d). Additional requirements. '"any additional requirements to comply with AFI 31- 101, Volume 1, the Air Force Installation Security Program, and AFI 31-501, Personnel Security Program Management"' 5352.242-9001 COMMON ACCESS CARDS (CAC) FOR CONTRACTOR PERSONNEL-AF SYSTEMS (NOV 2012)

  • Tax Law Section 5-A Section 5-a of the Tax Law, requires certain Contractors awarded State Contracts for commodities, services and technology valued at more than $100,000 to certify to the NYS Department of Taxation and Finance (DTF) that they are registered to collect New York State and local sales and compensating use taxes. The law applies to Contracts where the total amount of such Contractors’ sales delivered into New York State are in excess of $300,000 for the four quarterly periods immediately preceding the quarterly period in which the certification is made, and with respect to any affiliates and subcontractors whose sales delivered into New York State exceeded $300,000 for the four quarterly periods immediately preceding the quarterly period in which the certification is made. A Vendor is required to file the completed and notarized Form ST-220-CA with OGS certifying that the Vendor filed the ST-220-TD with the NYS Department of Taxation and Finance (DTF). Please note that the NYS Department of Taxation and Finance should receive the completed Form ST-220-TD, not OGS. OGS should only receive the Form ST-220-CA. Proposed Contractors should complete and return the certification forms within five (5) business days of request (if the forms are not completed and returned with Vendor Submission). Failure to make either of these filings may render a Vendor non- responsive and non-responsible. Each Vendor shall take the necessary steps to provide properly certified forms within a timely manner to ensure compliance with the law. Website links to the Contractor certification forms and instructions are provided below. Form No. ST- 220-TD must be filed with and returned directly to DTF and can be found at xxxx://xxx.xxx.xx.xxx/pdf/current_forms/st/st220td_fill_in.pdf. Unless the information upon which the ST-220-TD is based changes, this form only needs to be filed once with DTF. If the information changes for the Contractor, its affiliate(s), or its subcontractor(s), a new Form No. ST-220-TD must be filed with DTF. Form ST-220-CA must be submitted to OGS. This form provides the required certification that the Contractor filed the ST-220-TD with DTF. This form can be found at xxxx://xxx.xxx.xx.xxx/pdf/current_forms/st/st220ca_fill_in.pdf. Vendors may call DTF at 000-000-0000 for any and all questions relating to §5-a of the Tax Law and relating to a company's registration status with the DTF. For additional information and frequently asked questions, please refer to the DTF web site: xxxx://xxx.xxx.xx.xxx.

  • Reciprocal Compensation Arrangements Pursuant to Section 251(b (5) of the Act

Time is Money Join Law Insider Premium to draft better contracts faster.