Originating Goods For the purposes of this Agreement, a good shall be treated as an originating good if it is: (a) wholly obtained or produced in a Party as provided in Article 3.3 (Goods Wholly Obtained or Produced); (b) produced in a Party exclusively from originating materials from one or more of the Parties; or (c) produced in a Party using non-originating materials, provided the good satisfies the applicable requirements set out in Annex 3A (Product-Specific Rules), and meets all other applicable requirements of this Chapter.
Aircraft This peril includes self-propelled missiles and spacecraft.
Fleet In general, any in-house mechanic may be assigned to respond to any emergency during normal working hours in any of the three operating companies. (This does not supersede the Mechanic Personnel Working Across 309 Jurisdictional Boundaries Agreement dated October 4, 2007). Example 1: Lincoln (CILCO) unit breaks down in the northern part of its territory. It would make sense for the Bloomington (rp) mechanic to respond to the service call. Lincoln staffs a 2nd shift mechanic only and the vehicle in need of repair is closer to the Bloomington garage. This example covers areas that both have Ameren in-house mechanics. Example 2: Any CIPS 702 units could be repaired by Ameren staffed mechanics in 702 territories. This would generally happen in areas that are in close proximity to an IP or CILCO garage. This example covers 702 CIPS areas that do not have Ameren in-house mechanics. These jobs currently are outsourced. Perform Preventive Maintenance on CIPS 702 equipment at individual operating centers where advantageous. This work is currently outsourced. It is not the company’s intent to perform all PM’s with in-house mechanics.
Customer Support and Training System Agency will provide support for the CMBHS, including problem tracking and problem resolution. System Agency will provide telephone numbers for Grantees to obtain access to expert assistance for CMBHS-related problem resolution. System Agency will provide initial CMBHS training. Grantee shall provide subsequent ongoing end-user training.
Customer Agreement I certify that the information provided in this application is true and complete and declare that the Firm may rely upon such information until it receives written notice of any changes. I acknowledge that the intended use of my account is for investing or savings purposes unless notified otherwise.
Accessories, Spare Parts and Tools Accessories, spare parts and tools dispatched with a piece of equipment, machine, apparatus or vehicle, which are part of the normal equipment and included in the price thereof or which are not separately invoiced, shall be regarded as one with the piece of equipment, machine, apparatus or vehicle in question.
Spare Parts 14.1 As specified, the supplier may be required to provide any or all of the following materials, notifications, and information pertaining to spare parts manufactured or distributed by the supplier: (a) such spare parts as the purchaser may elect to purchase from the supplier, provided that this election shall not relieve the supplier of any warranty obligations under the contract and; (b) In the event of termination of production of the spare parts: (i) advance notification to the purchaser of the pending termination, in sufficient time to permit the purchaser to procure needed requirements and; (ii) Following such termination, furnishing at no cost to the purchaser, the blueprints, drawings, and specifications of the spare parts, if requested.
Customer Agreements 29.1 Trader to include provisions in Customer Agreements: The following clauses apply in respect of the Trader’s Customer Agreements: (a) in respect of each Customer Agreement that has been entered into prior to the Commencement Date: (i) at the next review date, or, if the Trader is able to unilaterally vary the Customer Agreement, within 12 months after the Commencement Date (whichever is earlier), the Trader must issue a unilateral variation to the Customer Agreement to include provisions that have substantially the same effect as the provisions required to be included in the Customer Agreement by this Agreement, and those provisions must be expressed to be for the benefit of the Distributor and enforceable by the Distributor in accordance with section 12 of the Contract and Commercial Law Act 2017; or (ii) if the Trader is unable to unilaterally vary 1 or more Customer Agreements as set out in subparagraph (i), the Trader must: (A) use all reasonable endeavours to obtain at the next review of each Customer Agreement, or within 12 months, whichever is earlier, the agreement of the Customer to enter into a variation of the Customer Agreement to include the provisions required to be included in the Customer Agreement by this Agreement, and those provisions must be expressed to be for the benefit of the Distributor and enforceable by the Distributor under section 12 of the Contract and Commercial Law Act 2017; and (B) promptly provide notice to the Distributor if it is unable to obtain the agreement of the Customer required in subparagraph (A); or (b) in respect of each Customer Agreement that has been entered into after the Commencement Date, include the provisions required to be included in the Customer Agreement by this Agreement, and those provisions must be expressed to be for the benefit of the Distributor and enforceable by the Distributor in accordance with section 12 of the Contract and Commercial Law Act 2017.
Durable Medical Equipment Durable Medical Equipment is equipment that is Medically Necessary for treatment of an illness or Accidental Injury or to prevent further deterioration. This equipment is designed for repeated use and used to treat a medical condition or illness, and includes items such as oxygen equipment, functional wheelchairs, and crutches. Durable Medical Equipment may require Prior Authorization. Only Durable Medical Equipment considered standard and/or basic as defined by nationally recognized guidelines are Covered.
Course Curriculum, Instruction, and Grading X. Xxxx College courses offered as dual credit, regardless of where they are taught, follow the same syllabus, course outline, textbook, grading method, and other academic policies as the courses outlined in the Hill College catalog. B. Approved courses being taught for dual credit must follow the approved master syllabus of the discipline and of Hill College. C. Textbooks should be identical to those approved for use by Hill College. Should an instructor propose an alternative textbook, the textbook must be approved in advance by the appropriate instructional department of Hill College and the Vice President of Instruction. Other instructional materials for dual credit/concurrent courses must be identical or at an equivalent level to materials used by Hill College. D. Courses which result in college‐level credit will follow the standard grading practices of Hill College, as identified by college policy and as identified in the appropriately approved course syllabus. The grades used in college records are A (excellent), B (above average), C (average), D (below average), F (failure), I (incomplete), W (withdrawn), WC (withdrawn COVID). The lowest passing grade is D. Grade point averages are computed by assigning values to each grade as follows: A = 4 points, B = 3 points, C = 2 points, D = 1 point, and F = 0 points. Grading criteria may be devised by Hill College and the ISD to allow faculty the opportunity to award high school credit only or high school and college credit depending upon student performance. E. Faculty, who are responsible for teaching dual credit/concurrent classes, are responsible for keeping appropriate records, certifying census date rosters, providing interim grade reports, certifying final grade reports at the end of the semester, certifying attendance, and providing other reports and information as may be required by Hill College and/or the School District.
