Shape and dimensions Sample Clauses

Shape and dimensions. 3.1.1. The shape and dimensions of samples are given in Figure 6. The thickness of the sample corresponds to the thickness of the product to be tested. It shall not be more than 13 mm. When taking the sample permits, the sample shall have a constant section over its entire length. Figure 6 Sample (Dimensions in millimetres) 3.1.2. If the shape and dimensions of a product do not permit taking a sample of the given size, the following minimum dimensions shall be maintained: (a) For samples having a width of 3 to 60 mm, the length shall be 356 mm. In this case the material is tested in the product's width; (b) For samples having a width of 60 to 100 mm, the length shall be at least 138 mm. In this case the potential burning distance corresponds to the length of the sample, the measurement starting at the first measuring point.
Sample 1Sample 2Sample 3See All (8)
AutoNDA by SimpleDocs
Shape and dimensions. As per the VT-200-F drawing shown on page 5 .
Sample 1Sample 2Sample 3
Shape and dimensions. Colouring of the plastic product .............................................................................................. Nature of the surface coating ................................................................................................... Secondary characteristics: Conductors incorporated (yes/no) ........................................................................................... Obscuration incorporated (yes/no) .......................................................................................... Remarks Documents attached: list of windscreens (see Appendix 13) (Principal and secondary characteristics as defined in Annex 18 to Regulation No. 43) Approval No. …………………………… Extension No. …………………………. Principal characteristics: Number of layers of plastic ..................................................................................................... Number of layers of interlayer ................................................................................................ Nominal thickness ................................................................................................................... Nominal thickness of interlayer (s............................................................................................ Nature and type of interlayer (s) .............................................................................................. Special treatment of plastic ..................................................................................................... Colouring of plastic product .................................................................................................... Chemical designation of single sheet material ........................................................................ Classification of the material ................................................................................................... Process of manufacture ...........................................................................................................
Sample 1
Shape and dimensions. As per the SP-T2A-F drawing shown on page 5 .
Sample 1Sample 2
Shape and dimensions. As per the SSP-T7-F drawing shown on page 5 .
Sample 1Sample 2
Shape and dimensions. Nature of the surface coating ............................................................................
Sample 1
Shape and dimensions. The shape and dimensions of samples are given in figure 20. The thickness of the sample corresponds to the thickness of the product to be tested. It shall not be more than 13 mm. When sample-taking so permits, the sample shall have a constant section over its entire length. When the shape and dimensions of a product do not permit taking a sample of the given size, the following minlmimi dimensions shall be observed : (a) for samples having a width of 3 to 60 шш, the length shall be 356 mm. In this case the material is tested over the product's width; (b) for samples having a width of 60 to 100 шш, the length shall be at least 138 ШШ. In this case the potential burning distance corresponds to the length of the sample, the measurement starting at the first measuring (c) samples less than 60 mm wide and less than 356 пш. long, 'and samples 60 to
Sample 1
AutoNDA by SimpleDocs

Related to Shape and dimensions

  • Permitted Uses and Disclosures of PHI and the third party notifies the Business Associate of any instances of which it is aware in which the confidentiality of the information has been breached.

  • Permitted Uses and Disclosures i. Business Associate shall use and disclose PHI only to accomplish Business Associate’s obligations under the Contract. i. To the extent Business Associate carries out one or more of Covered Entity’s obligations under Subpart E of 45 C.F.R. Part 164, Business Associate shall comply with any and all requirements of Subpart E that apply to Covered Entity in the performance of such obligation. ii. Business Associate may disclose PHI to carry out the legal responsibilities of Business Associate, provided, that the disclosure is Required by Law or Business Associate obtains reasonable assurances from the person to whom the information is disclosed that: A. the information will remain confidential and will be used or disclosed only as Required by Law or for the purpose for which Business Associate originally disclosed the information to that person, and; B. the person notifies Business Associate of any Breach involving PHI of which it is aware. iii. Business Associate may provide Data Aggregation services relating to the Health Care Operations of Covered Entity. Business Associate may de-identify any or all PHI created or received by Business Associate under this Agreement, provided the de-identification conforms to the requirements of the HIPAA Rules.

  • Permitted Uses and Disclosures by Business Associate Except as otherwise limited by this Agreement, Business Associate may make any uses and disclosures of Protected Health Information necessary to perform its services to Covered Entity and otherwise meet its obligations under this Agreement, if such use or disclosure would not violate the Privacy Rule if done by Covered Entity. All other uses or disclosures by Business Associate not authorized by this Agreement or by specific instruction of Covered Entity are prohibited.

  • Markings If permitted by applicable Law, on or reasonably promptly after the Closing Date, Owner will cause to be affixed to, and maintained in, the cockpit of the Airframe and on each Engine, in each case, in a clearly visible location, a placard of a reasonable size and shape bearing the legend: “Subject to a security interest in favor of Wilmington Trust, National Association, not in its individual capacity but solely as Mortgagee.” Such placards may be removed temporarily, if necessary, in the course of maintenance of the Airframe or Engines. If any such placard is damaged or becomes illegible, Owner shall promptly replace it with a placard complying with the requirements of this Section.

  • Prohibited Uses and Disclosures BA shall not use or disclose PHI other than as permitted or required by the Contract and Addendum, or as required by law. BA shall not use or disclose Protected Information for fundraising or marketing purposes. BA shall not disclose Protected Information to a health plan for payment or health care operation purposes if the patient has requested this special restriction, and has paid out of pocket in full for the health care item or service to which the PHI solely relates [42 U.S.C. Section 17935(a) and 45 C.F.R. Section 164.522(a)(vi)]. BA shall not directly or indirectly receive remuneration in exchange for Protected Information, except with the prior written consent of CE and as permitted by the HITECH Act, 42 U.S.C. Section 17935(d)(2), and the HIPAA regulations, 45 C.F.R. Section 164.502(a)(5)(ii); however, this prohibition shall not affect payment by CE to BA for services provided pursuant to the Contract.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!