Principal characteristics. Remarks: For laminated glass panes with enhanced mechanical properties with additional symbol /D (yes/no) 1 ...................................................................................................................................... 1 Strike out what does not apply." Annex 7
Principal characteristics. Composition of double-glazed units (symmetrical/asymmetrical): .................. Nominal thickness of the gap: .......................................................................... Method of assembly: ......................................................................................... Type of each glazing component as defined in Xxxxxxx 0, 0, 0, 00 xx 00: ....... ...........................................................................................................................
Principal characteristics. Shape category: Number of layers of plastics: Normal thickness of glass: Treatment of the glass (yes/no): Nominal thickness of the windscreen: Nominal thickness of the layer(s) of plastics acting as interlayer: Nature and type of layer(s) of plastics acting as interlayer: Nature and type of the outer layer of plastics: Secondary characteristics: Nature of the material (plate, float, sheet glass): Colouring of glass: Colouring of the layer(s) of plastics (total/partial): Conductors incorporated (yes/no): Opaque obscuration incorporated (yes/no): Remarks: ______________________________________________________________________________________ Documents attached: list of windscreens (see Appendix 13) Annex 1 - Appendix 6 Glass-plastics panes (Principal and secondary characteristics as defined in Annex 11 to Regulation No. 43)
Principal characteristics. Composition of multiple glazed units (symmetrical/asymmetrical): ................ Nominal thickness of the gap: .......................................................................... Method of assembly: ......................................................................................... Type of each glazing component as defined in Xxxxxxx 0, 0, 0, 00 xx 00: ....... ........................................................................................................................... Documents attached: One form for all panes of a symmetrical multiple glazed unit in accordance with the annex under which the panes have been tested or approved. One form for each different pane of an asymmetrical multiple glazed unit in accordance with the annexes under which these panes have been tested or approved. Remarks: ....................................................................................................................... ...................................................................................................................................... ...................................................................................................................................... Annex 1 - Appendix 8 Rigid plastic panes
Principal characteristics. Chemical designation of the material: ............................................................................................... Process of manufacture: .................................................................................................................... Nominal thickness:............................................................................................................................ Colouring of the plastic product:....................................................................................................... Nature and type of surface coating: ...................................................................................................
Principal characteristics. The vessel shall be a monohull diesel-powered twin screw survey vessel designed for year round surveying operations. The vessel’s principal characteristics shall be as follows: • Length (bow to transom) 48 to 52 feet (longer within this range is better) • Beam (fender to fender) 15 to 17 feet (wider within this range is better) • Maximum Design Draft 4.5 feet maximum (less draft is better) The vessel shall have a minimum cruise speed of 25-30 knots (faster is better) at 85% engine rated power and the full load condition, defined in contract Clause C150. The minimum speed at the full load condition identified by the proposer shall be a contractual requirement. The vessel’s freeboard shall be suitable for open ocean operation. The vessel shall have a flat single-level main deck. The Contractor shall develop and submit a hull lines plan as 846-C105-01 HULL LINES to the COR during Phase I of the contract.
Principal characteristics. Chemical designation of the material: The classification of the material by the manufacturer: Process of manufacture: Shape and dimensions: Nominal thickness: Colouring of the rigid plastic material: Nature and type of surface coating: Secondary characteristics: Conductors incorporated (yes/no): Remarks: Annex 1 - Appendix 9 Flexible plastic panes (Principal and secondary characteristics in accordance with Annex 15 to Regulation No. 43)
Principal characteristics. Composition of double-glazed units (symmetrical/asymmetrical) . . . . . . : Nominal thickness of the gap: . . . . . . . . . . . . . . . . . . . . . . : Method of assembly: . . . . . . . . . . . . . . . . . . . . . . . . . . . : Type of each glazing component as defined in annexes 5, 7, 9, 11 or 14 . : Documents attached: One form for the two panes of a symmetrical double-glazed unit in accordance with the annex under which the panes have been tested or approved. E/ECE/324 Rev.1/Add.42/Rev.1/Amend.1 Regulation No. 43 page 14 One form for each pane of an asymmetrical double-glazed unit in accordance with the annexes under which these panes have been tested or approved. Remarks" Insert new Annex 1 - Appendices 8 and 9, to read: "Annex 1 — Appendix 8 RIGID PLASTICS PANES OTHER THAN WINDSCREENS (Principal and secondary characteristics in accordance with annex 14)
Principal characteristics. Chemical designation of the material : The classification of the material by the manufacturer.......................: Process of manufacture.......................................................: Shape and dimensions.........................................................: Nominal thickness............................................................: Colouring of the rigid plastic material......................................: Nature and type of surface coating...........................................: Secondary characteristics Conductors incorporated (YES/NO).............................................: Remarks Annex 1 — Appendix 9 PANES OF FLEXIBLE PLASTICS OTHER THAN WINDSCREENS (Principal and secondary characteristics in accordance with annex 15)
Principal characteristics. These specifications are intended to describe the contract design for one inland river crane barge. The principal dimensions of the barge are: Length Overall Beam Overall Molded Depth (@ C.L.) Molded Depth (@ Side) 200’-0”56’-0”10’-6”10’-0” Light Ship Draft 6’-0” Max Draft 6’-6” C010 DEFINITIONS The following definitions are applicable to phrases and acronyms used throughout this contract: • ABS – American Bureau of Shipping • COR - Contracting Officer’s Representative - a member of the contract management and quality assurance team authorized by the Contracting Officer to perform certain administrative and managerial duties. A copy of the COR’s authority letter is furnished to the Contractor. • GFE – Government Furnished Equipment – Equipment, materials or components furnished by the Government to the Contractor for installation on the vessel. • K.O. - Contracting Officer - A person with the authority to enter into, administer and/or terminate contracts and make related determinations and findings. • MDC – Acronym for the Marine Design Center. • QC - Quality Control - Quality Control is a function of the Contractor. Refer to clause E03. Quality Assurance (QA) is a function of the Government. • USACE – Acronym for United States Army Corps of Engineers. • USCG - Acronym for United States Coast Guard.
