SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officer, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 8 contracts
Samples: Construction Contract, General Terms & Conditions, General Terms & Conditions
SPECIFICATIONS AND DRAWINGS. (
a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, drawings or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.such
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 6 contracts
Samples: Contract for Activate Dental Clinic, Contract for Burger King Image Upgrade, Contract for Conversion of Food Service
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement OfficerSubcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications.
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
(7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 4 contracts
Samples: Construction Contract, General Terms & Conditions, General Terms & Conditions
SPECIFICATIONS AND DRAWINGS. (a) Seller A. Contractor shall be furnished keep, at the number of drawings and specifications specified in Division One at no cost.
(b) Seller shall keep on the work site Work site, a copy of the drawings and specifications required by this Agreement and shall at all times give Company provide Owner access thereto. Anything mentioned in the specifications and not shown on shall have the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like same effect as if shown or mentioned in both. In case of difference between both drawings and specifications, the specifications shall govern. Within the specifications, Division One shall govern. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter discrepancy shall be promptly submitted to the Technical Project Officer and the Procurement Officerimmediately submitted, who shall promptly make a determination in writing, to Owner. Any adjustment Discrepancies shall not be resolved by Seller Contractor without such a determination shall be decision of Owner, except at its own Contractor's risk and expense. Company Owner shall furnish resolve such discrepancy in writing or by releasing a clarifying revision on the figure, drawing or specification. Owner may furnish, from time to time time, such detailed drawings other detail drawings, specifications and information as it may consider necessary. All drawings, plans, specifications, data and other information as considered necessaryfurnished by Owner to Contractor, unless otherwise providedor developed by Contractor in the performance of this Agreement, shall remain, or become, the property of Owner and Contractor shall deliver the original and all copies of all such documents to Owner upon completion and acceptance, or termination, of the Work.
(1) The B. Whenever the specifications or drawings indicate or specify by patent or proprietary material name or manufacturers' name, such material or process shall generally be deemed to be required and “NO SUBSTITUTIONS" shall be made without the express written approval of Owner. Nevertheless, with regard to materials that qualify as "Or Equal", Contractor may request, and Owner may authorize, use of such "Or Equal" materials, in writing. In the event Contractor, or its Subcontractors at any tier, uses materials, supplies, goods or processes not permitted by the specifications incorporated into or drawings or authorized by Owner, Contractor shall be obligated to remove and replace such materials, at the request of Owner, at no cost to Owner. This clause is in addition to Owner's other remedies as provided herein.
C. All lists, rules, regulations and standards referred to in this Agreement are intended recognized as requirements of this Agreement. When American Society of Testing Materials (ASTM) Specifications are referred to, it is understood to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact mean that every item necessarily involved may not be specifically mentioned.
(2) Omissions from the drawings or these ASTM specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and latest ASTM specifications.
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
(7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 3 contracts
Samples: General Terms and Conditions, General Terms and Conditions, Construction Contract
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, drawings or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed detail drawings and other information as considered the contracting officer may consider necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2) . Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3) The . In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer. It The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility for the dimensions and design of adequate connections, details and satisfactory construction of all work. During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to define lowerall changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer. Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractors' limits subcontractor pursuant to a construction contract, showing in detail, (1) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The Exchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. The subparagraph "f" shall be included in all subcontracts hereunder at any tier. The contractor shall lay out the contractor’s work from base lines and to ensure that grades established by the Exchange and shall be responsible for all lower-tier subcontractors measurements in connection therewith. The contractor shall, at the contractor’s own expense, furnish all stakes, templates, platforms, equipment and suppliers at whatever level are familiar with all provisions of this Agreement ranges and labor that may affect be required in setting and cutting, or laying out any part of the work. The contractor will be held responsible for the proper execution of the work to such lines and grades as may be established or indicated by the contracting officer, and all stakes or other marks thus established shall be preserved by the contractor until their work.
(7) removal is authorized by the contracting officer. The data sheet equipment numbers are not unique. Multiple pieces contracting officer xxxx xxxxxxx, on request from the contractor, all location and limit marks reasonably necessary for the conduct of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 3 contracts
Samples: Contract for Shopping Center Image Upgrade, Contract for Services, Contract for Ordinance Troop Store Mpa Expansion
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.such
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 2 contracts
Samples: Contract for Electrical Improvements, Contract for Family Recreation Center
SPECIFICATIONS AND DRAWINGS. (
a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed detail drawings and other information as considered the contracting officer may consider necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed details mis-described
c) In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be done from the general nature and tendency of the plans and descriptions. Plans and drawings remain the property of the Exchange and shall be returned upon completion of the work, but they . Contractor shall be performed as if fully and correctly set forth and described in not deviate from the drawings and or specifications.
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 1 contract
Samples: Contract for Deca Commissary Upgrade
SPECIFICATIONS AND DRAWINGS. (
a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, drawings or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed detail drawings and other information as considered the contracting officer may consider necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed details mis-described
c) In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be done from the general nature and tendency of the plans and descriptions. Plans and drawings remain the property of the Exchange and shall be returned upon completion of the work, but they . Contractor shall be performed as if fully and correctly set forth and described in not deviate from the drawings and or specifications.
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 1 contract
Samples: Contract for Relocate Express
SPECIFICATIONS AND DRAWINGS. (a) Seller The drawings furnished to the Contractor shall be furnished interpreted and identified by figured dimensions and nomenclature as indicated therein. On no occasion the number drawings shall be scaled off and transferred to work. In all cases where enlarged detailed drawings are given for any component of work, these drawings and specifications specified shall take precedence over those incorporated in Division One at no costgeneral drawing to a comparatively smaller scale.
(b) Seller shall keep on a. Prior to the work site a copy execution of the drawings and work, the Contractor shall check all drawings, specifications and shall immediately report all errors, discrepancies and / or omissions discovered therein to NIRM and obtain appropriate corrections/orders on the same. Any adjustment made by the Contractor without prior approval of the NIRM shall be at all times give Company access thereto. Anything mentioned his own risk, each description of item in the schedule of quantities shall be read in conjunction with the relevant drawings and the specifications and not shown on the Contractor’s rate shall be deemed to be for such complete work unless otherwise specified by the Contractor while tendering.
b. Cost of all shop drawings, fabrication drawings, or shown on the form work drawings and not mentioned in details to be furnished by the specifications, Contractor shall be deemed to be included in his tendered rates for the work. Accordingly, approval to shop drawings or other fabrication drawings shall not be construed as authorising award of like effect additional work and as if shown long as these belong to common individual scheme governed by specifications for which the Contractor has already quoted, no extra payment on any account will be admissible for all essential components that are to be necessarily executed to complete the work in all respects.
c. Prior to submission for approval, the Contractor shall be responsible for thoroughly checking all drawings to ensure that they comply with the intent and requirements of the contract specifications and they fit with the over all building layout. Drawing found to be inaccurate or mentioned otherwise in botherror will be returned for correction by the Contractor.
d. For all drawings to be submitted by the Contractor for the approval of NIRM, the Contractor shall submit 6 (six) copies of each drawing for approval.
e. The approval of drawing by NIRM shall not be construed as a complete dimensional check, but will indicate only that the general method of construction and detailing is satisfactory. The Contractor shall be totally responsible for the dimensions and design, safety of the system evolved inclusive of providing interconnected operational accessories adequate enough to accomplish satisfactory completion of work.
f. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One shall govern. In case of discrepancy Anything mentioned in the figures, specification and not shown in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officer, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of shown on the drawings and specifications, or that are customarily performed, shall but not relieve Seller from performing such omitted or misdescribed details of mentioned in the work, but they specifications shall be performed like effect as if fully and correctly set forth and described shown or mentioned in the drawings and specificationsboth.
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
(7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 1 contract
SPECIFICATIONS AND DRAWINGS. (
a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.such
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 1 contract
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed detail drawings and other information as considered the contracting officer may consider necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their workkind whatsoever, unless the same be authorized in writing by the contracting officer.
(7d) The data sheet equipment numbers are contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not uniquebe construed as a complete check, but will indicate only that the general method of construction
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. Multiple pieces The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of equipment all subsurface utility lines in order that the location of these lines and the appurtenances may utilize be determined in the same numberevent the surface openings or indicators become covered or obscured. Seller The record drawings shall determine show by offset dimensions two permanently fixed surface features at the quantity end of equipment each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and material needed will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to complete separately placed facilities or the workcontract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (1) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The Exchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. The subparagraph "f" shall be included in all subcontracts hereunder at any tier.
Appears in 1 contract
Samples: Construction Contract
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed detail drawings and other information as considered the contracting officer may consider necessary, unless otherwise provided.
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 1 contract
Samples: Contract for Services
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller a. The Contractor shall keep on the work site Site a copy of the drawings and specifications and shall at all times give Company L3Harris access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference differences between drawings and specifications, the specifications shall govern. Within the specifications, Division One shall govern. In any case of discrepancy either in the figures, in the drawings, drawings or in the remainder of the specifications, specifications the matter shall be promptly submitted to the Technical Project Officer and the an authorized L3Harris Procurement OfficerRepresentative, who shall promptly make a determination in writing. Any adjustment by Seller the Contractor without such a this written determination shall be at its the Contractor's own risk and expense. Company L3Harris shall furnish from time to time such detailed detail drawings and other information as may be considered necessary, unless otherwise provided.
(1) The drawings b. Omission and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2) Omissions Misdescriptions\MOmissions from the drawings or specifications or the misdescription of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, specifications or that which are customarily performed, shall not relieve Seller the Contractor from performing such omitted or misdescribed details of the or work, but they shall be performed as if fully and correctly set forth and described in the drawings and specificationsspecifications after notifying a L3Harris authorized representative of such omission or misdescription.
c. Checking of Drawings and Dimensions\MThe Contractor shall check all drawings furnished him immediately upon their receipt and shall promptly notify L3Harris in writing of any discrepancies. Figures marked on drawings shall, in general, be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The Contractor shall compare all drawings and verify the figures before laying out the work and will be responsible for any errors which might have been avoided thereby. When measurements are affected by conditions already established, the Contractor shall take measurements notwithstanding the giving of scale or figure dimensions in the drawings.
d. Deviations\MDeviations from the drawings and the dimensions therein given, whether or not an error is believed to exist, shall be made only after written authority is obtained from L3Harris.
e. Base Lines and Grades\MThe Contractor shall lay out its work from L3Harris established lines and benchmarks indicated on the drawings or established by L3Harris, and shall be responsible for all measurements in connection with the layout. The Contractor shall furnish, at its own expense, all stakes, templates, platforms, equipment, tools, materials, and labor required to lay out any part of the work. The Contractor shall be responsible for executing the work to the lines and grades that may be established or indicated by L3Harris. The Contractor shall also be responsible for maintaining and preserving all stakes and other marks established by L3Harris until authorized to remove them. If such marks are destroyed by the Contractor or through the Contractor's negligence before their removal is authorized, L3Harris may replace them and deduct the expense of the replacement from any amount due or to become due to the Contractor.
f. Special Shop Drawings\MWhenever required by the specifications, the Contractor shall make special or detailed shop drawings in amplification of the drawings referred to in this Contract, or in furtherance of the specifications before proceeding with the work. Such drawings shall be submitted to L3Harris in duplicate, and in such format as L3Harris may prescribe. Such drawings shall (3i) reflect the Contract number, (ii) show in detail the proposed fabrication and assembly of structural elements, and (iii) in detail show the installation (i.e., form, fit, and attachment details) of materials of equipment. Such drawings shall include such diagrams, layouts, schematics, descriptive literature, illustrations, schedules, performance and test data, and similar materials furnished by the Contractor to completely explain in detail the specific portion of work required by this Contract.
g. It is understood that all special shop drawings shall be reviewed by the Contractor prior to submitting, in duplicate to L3Harris for approval, for accuracy, completeness, and compliance with Contract requirements and shall indicate the Contractor's approval on each drawing as evidence of such coordination and review. Any drawings submitted to L3Harris without evidence of the Contractor's approval shall be returned for resubmission. L3Harris will indicate an approval or disapproval of the shop drawings and if not approved as submitted shall indicate L3Harris' reasons therefore. Any work done before such approval shall be at the Contractor's risk. Approval by L3Harris shall not relieve the Contractor from responsibility for any errors or omissions in such drawings, or from responsibility for complying with the requirements of this Contract.
h. It is further understood that the approval by L3Harris of the Contractor's drawings, whether general or detailed, is a general approval relating only to their sufficiency and compliance with the intention of the Contract and shall not excuse or constitute a waiver of errors, discrepancies, or omissions, or of detailed requirements. When a drawing has been approved the Contractor shall furnish L3Harris with four (4) additional prints with the tracing or a reproducible print. If a tracing is submitted, L3Harris will make such prints as are required and will return the tracing to the Contractor. All drawings shall become the property of L3Harris, and L3Harris shall be entitled, without further payment or liability to the Contractor and without further permission, to use such drawings and to reproduce them; provided, however, the use of such drawings shall not imply a license to L3Harris under any patent and shall not be construed as affecting the scope of any license otherwise granted to L3Harris under any patent.
i. The specifications and drawings may identify and Contractor shall furnish to L3Harris four (4) complete sets of certified shop drawings, a complete list quantities of items materials to be furnished used, fabrication and welding procedures, specifications, and any applicable standards and shall receive L3Harris written approval of the drawings or specifications, as noted, before starting fabrication. All required corrections shall be made and current shop drawings shall be submitted for approval prior to commencing fabrication.
j. Approvals of shop drawings shall not relieve the Contractor from responsibility of producing completed and installed by Sellerwork in strict conformance with the drawings, specifications, Contractor's approved drawings and specifications, and applicable codes and regulations. These identifications may be incomplete and L3Harris will not assume the quantities are estimates only. Seller is responsible responsibility for furnishing searching out deviations in the items and quantities manifestly necessary to carry out the intent of the Contractor's shop drawings and specifications.
(4) The k. Upon completion of the work, one print of each of the drawings furnished accompanying this specification and any drawings subsequently issued in accordance with the stipulations heretofore set forth shall be neatly and clearly marked\Min red\Mto show all variations between the construction actually provided and that indicated or specified by Company arethe Contract Documents, and shall be delivered to L3Harris. Where a choice of material, equipment and/or methods is permitted herein, or where variations in general, to scale. Scales shown on a microfilmed reproduced drawing the scope or character of the work from that indicated or specified is permitted by subsequent change in proportion to the reduction Contract, such choices or variations shall be reflected by the "as-built" drawings. The representations and such supplementary notes, legends, and details as may be necessary for legibility and clear portrayal on the as-built construction prints shall be subject to approval by L3Harris before final acceptance of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaledfacility.
(5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
(7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 1 contract
Samples: General Agreement
SPECIFICATIONS AND DRAWINGS. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost.
(b) Seller The contractor shall keep on at the work site a current copy of the drawings and specifications and shall at all times give Company the contracting officer access thereto. Anything mentioned in the specifications and not shown on the drawings, drawings or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within Figures marked on drawings shall in general be followed in preference to scale measurements. Large scale drawings shall, in general, govern small scale drawings. The contractor shall compare all drawings and verify before laying out the specificationswork and will be responsible for any errors which might have been avoided thereby. Further, Division One the contractor shall governcheck all drawings, figures and specifications immediately upon their receipt. In any case of discrepancy in the figures, in the drawings, drawings or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officercontracting officer, who shall promptly make a determination in writing. Any adjustment by Seller contractor without such a determination shall be at its own the contractor’s risk and expense. Company The contracting officer shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided.such
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.
(2b) Omissions from the drawings or specifications or the misdescription mis-description of details of work that which are manifestly necessary to carry out the intent of the drawings and specifications, or that which are customarily performed, shall not relieve Seller the contractor from performing such omitted or misdescribed mis-described details of the work, but they shall will be performed as if fully and correctly set forth and described in the drawings and specifications.
(3c) The In addition to the requirements of subparagraph "a" above, contractor hereby acknowledges receipt of all plans, drawings and specifications identified as Exhibits to this contract. Contractor agrees and admits that the said plans, drawings and specifications and drawings may identify and list quantities of items particulars are sufficient for their intended purpose without any additional extra work, other than the work set forth thereby or necessarily inferred to be furnished done from the general nature and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent tendency of the plans and descriptions. Plans and drawings and specifications.
(4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to remain the reduction property of the drawing Exchange and shall be returned upon completion of the work. Contractor shall not deviate from original size. Figured dimensions shall always be followed and the drawings not scaled.
(5) Prior to fabricating or specifications, or execute any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of extra work of any subcontractorkind whatsoever, unless the same be authorized in writing by the contracting officer.
d) The contractor shall submit to the contracting officer for approval, with such promptness as to cause no delay in the contractor’s own work or in that of any other contractor, copies of all shop or installation drawings and schedules required for the work of the various trades called for under the various headings of the specifications. It Unless otherwise stipulated in the specifications, six copies of each such shop or installation drawing and schedule will be submitted. These drawings and schedules shall be complete and detailed. The contractor shall make any and all corrections required by the contracting officer, file with the contracting officer four corrected copies and furnish such other copies as may be needed. If the contractor considers any corrections indicated on the drawings to constitute a change to the contract drawings or specifications, notice as required under the clause entitled "Changes" will be given to the contracting officer. The contracting officer's approval of such drawings or schedules shall not be construed as a complete check, but will indicate only that the general method of construction and detailing is Seller's satisfactory. Approval of such drawings will not relieve the contractor of responsibility to define lower-tier subcontractors' limits for the dimensions and design of work adequate connections, details and to ensure that satisfactory construction of all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
e) During the progress of the job, the contractor shall keep a careful record at the job site of all changes and corrections from the details shown on the drawings. The contractor shall enter such changes and corrections on contract drawings promptly, but in no case later than on a weekly basis. The record drawings shall indicate, in addition to all changes and corrections, the actual location of all subsurface utility lines in order that the location of these lines and the appurtenances may be determined in the event the surface openings or indicators become covered or obscured. The record drawings shall show by offset dimensions two permanently fixed surface features at the end of each run including each change in direction. The average depth below the surface of each run shall also be recorded. At the time of beneficial occupancy of each structure or facility involved under this contract, the contractor shall submit to the contracting officer as-built prints showing the aforementioned data. If the contractor fails to maintain the record drawings as required herein, the contracting officer will deduct from the monthly progress payment an amount representing the estimated monthly cost of maintaining the record drawings and will continue deduction of the 10% retainage even after completion of the contract. In addition, final payment with respect to separately placed facilities or the contract as a whole will be withheld until proper as-built drawings have been furnished to the contracting officer.
f) Shop drawings for construction means drawings, submitted to the Exchange by the contractor, subcontractor or any lower tier subcontractor pursuant to a construction contract, showing in detail, (71) the proposed fabrication and assembly of structural elements and (2) the installation (i.e. form, fit and attachment details) of materials or equipment. The data sheet equipment numbers are not uniqueExchange may duplicate, use and disclose in any manner and for any purpose shop drawings delivered under this contract. Multiple pieces of equipment may utilize the same number. Seller The subparagraph "f" shall determine the quantity of equipment and material needed to complete the workbe included in all subcontracts hereunder at any tier.
Appears in 1 contract
SPECIFICATIONS AND DRAWINGS. General Provisions 40 (Performance of Work by the Contractor) is supplemented as follows.
(a) Seller Six (6) sets of contract drawings and specifications along with one (1) set of reproducibles will be furnished to the contractor after issuance of the Notice to Proceed. The reproducible drawings shall be used in the preparation of "As-Built" drawings which shall show all revisions made as a result of contract modifications. This set of reproducibles shall be furnished by the number of contractor upon contract completion. See as-built drawings and specifications specified in Division One at no costparagraph for further information.
(b) Seller The contractor shall keep on the work site a copy check all drawings immediately upon receipt. Drawings shall not be scaled. Large scale drawings shall in general govern over small scale drawings. On any of the drawings where a portion of the work is drawn out and specifications the remainder is shown in outline, the parts drawn out shall apply also to all other like portions of the work. Schedules on the drawings shall take precedence over conflicting drawing information.
(c) The contractor shall submit, for approval, at least four (4) sets of shop drawings in accordance with Additional General Provisions 17 (Specifications and Drawings for Construction). ANTHC will retain three (3) sets of the submittal for ANTHC files. Shop drawings, coordination drawings and equipment schedules shall be submitted within fourteen (14) calendar days after date of receipt of Notice to Proceed or according to the approved submittal schedule.
(d) Prior to submission of shop drawings on the mechanical and electrical work, the contractor shall submit lists of mechanical and electrical equipment and materials as required by the specifications, and shall at all times give Company access theretoobtain the Project Manager's approval thereof. Anything mentioned in Drawings and schedules shall be delivered to the Project Manager, unless otherwise directed.
(e) Material and equipment submittals as required by the specifications and not shown on drawings shall be made in at least four (4) copies, three (3) of which will be retained by ANTHC.
(f) As soon as possible after the issuance of the Notice to Proceed, the contractor shall submit composite drawings, as specified, showing coordination of mechanical and electrical work with structural and architectural work. The composite drawing shall be in detail to show overall dimensions of duct work, piping, conduit and related items and clearances between structural members, lighting, ceilings, and related architectural features. The drawings should indicate any conflicts or clearance problems between the various trades. Installation of work prior to submission of these drawings, or shown on failure to point out such conflicts or clearance problems in the drawings and not mentioned will be at the contractor's risk. Composite drawings shall be submitted where appropriate or where called for in the technical specifications, .
(g) The contractor shall be of like effect as if shown or mentioned in both. In case of difference between submit all drawings and specificationsschedules in advance of construction requirements to permit approval and checking, the specifications shall govern. Within the specifications, Division One shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Technical Project Officer and the Procurement Officer, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed appropriate action.
(h) The approval drawings and other information as considered necessaryschedules will be general, unless otherwise provided.but approval shall not be construed:
(1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and necessary to complete As permitting any departure from the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned.contract requirements;
(2) Omissions from As relieving the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent contractor of the drawings and specificationsresponsibility for any errors, or that are customarily performedincluding details dimensions, shall not relieve Seller from performing such omitted or misdescribed details of the workmaterials, but they shall be performed as if fully and correctly set forth and described in the drawings and specificationsetc.;
(3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications.
(4) The drawings As approving departure from details furnished by Company arethe Project Manager, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaledexcept as otherwise provide herein.
(5) Prior to fabricating any item (structural steel, piping, ductwork, etc.), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution.
(6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.
(7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.
Appears in 1 contract
Samples: Memorandum of Agreement
