Metering Equipment 13.01. Utility will furnish, install, own and maintain metering equipment capable of measuring the flow of kilowatt-hours (kWh) of energy. The Customer's service associated with the CRG will be metered at a single metering point. The metering equipment will measure energy delivered by Utility to Customer and also measure energy delivered by Customer to Utility. Customer agrees to provide safe and reasonable access to the premises for installation of this equipment and its future maintenance or removal.
Testing of Metering Equipment Connecting Transmission Owner shall inspect and test all of its Metering Equipment upon installation and at least once every two (2) years thereafter. If requested to do so by NYISO or Developer, Connecting Transmission Owner shall, at Developer’s expense, inspect or test Metering Equipment more frequently than every two (2) years. Connecting Transmission Owner shall give reasonable notice of the time when any inspection or test shall take place, and Developer and NYISO may have representatives present at the test or inspection. If at any time Metering Equipment is found to be inaccurate or defective, it shall be adjusted, repaired or replaced at Developer’s expense, in order to provide accurate metering, unless the inaccuracy or defect is due to Connecting Transmission Owner’s failure to maintain, then Connecting Transmission Owner shall pay. If Metering Equipment fails to register, or if the measurement made by Metering Equipment during a test varies by more than two percent from the measurement made by the standard meter used in the test, Connecting Transmission Owner shall adjust the measurements by correcting all measurements for the period during which Metering Equipment was in error by using Developer’s check meters, if installed. If no such check meters are installed or if the period cannot be reasonably ascertained, the adjustment shall be for the period immediately preceding the test of the Metering Equipment equal to one-half the time from the date of the last previous test of the Metering Equipment. The NYISO shall reserve the right to review all associated metering equipment installation on the Developer’s or Connecting Transmission Owner’s property at any time.
MEASURING EQUIPMENT 1. Seller will maintain and operate, atlts own, expense and atthe point of delivery of gas hereunder, a meter or meters and othernecessary equipment by which the volume of gas delivered hereunder shall be measured. Such meters and equipment shall remain the property of the Seller.
2. Buyer agrees lo furnish to Seller electricity for operating Seller's meters, at not cost to Seller.
3. Buyer hereby grants to Seller suitable rlghts-0f-way and easements necessary or Incidental for the installatioo, maintenance, operation and removal of pipeline and other facilities together with rights ofingress thereto and egress there from at all times and hereby agrees to deliver to Seller, for the sum of one dollar ($1.00), an appropriate instrument or grant defining such rights and easements located on Buyer's planlslte.
4. Buyer may install, maintain and operate such check measuring equipment, Including arecording gravltometer and calorimeter as it shall desire, provided that such equipment shall be so installed so as not to Interfere with the operation of Seller's measuring equipment at or near the point of deliver. However, all xxxxxxxx to the Buyer shall be based on the metering of the Seller, subject only to the provisions of Paragraph 8 of this Article.
5. Each party shall have the right to be present at the time of any installing, reading, cleaning, changing, repairing, Inspecting, testing, calibrating, or adjusting done In connection with the other's measuring equlpme!lt used in measuring deliveries hereunder and each party shall advise the other of any Intended major maintenance operation sufficiently in advance in order that the other party may conveniently have its representative present.
6. All installatioo of measuring equipmenL applying to or effecting deliveries hereunder, shall be rnade in such manner as to perrnit an accurate detenninalion of the quantity of gas delivered and ready verification of the accuracy of measurement Orifice meter Installations, If used, shall oonforrn lo the recommendation for design and lnstallatioo contained in the Gas Measurement Commiltee Report No. 3 to the American Gas Association published April, 1955, and any modificatioos and amendments thereof and shall include the use of flange connections.
7. Measurement on Seller's meter or meters shall be conclusive of both parties except where the meter Is defective or fails to register, or if found in E)rror, in either of which case Seller shall repair or replace the meter and the quantity of gas delivered while the meter was out of order or failed to register shall be estimated:
(a) By using the registration of any check meter If installed and accurately registering, or, In the absence of (a): (b) By correcting the error If the percentage of error by calibration, test or mathematical calculation, or, in the absence of both (a) and (b) then: (c) By estimating the quantity of delivery from deliveries during periods under similar oonditions when the meter was registering actUrately; and an appropriate billing adjusbnentshall be made In accordance with the current Rules and Regulations governing gas systems issued by the Commission.
8. Seller will maintain its meters in .good order and to this end Wiii make periodic tests of its meters pursuant to the current Rules and Regulations governing gas systems issued by the Commission, or at such shorter intervals as seem to Seller desirable. lfBuyer Is dissatisfied with the accuracy at eny time, it may call upon Seller to have Iha meter tested in accordance with all regulatioos relating to such tests and results of such tesls as found in the current Rules and Regulations governing gas systems issued by the Commission.
9. Each party shall preserve all records for aperiod of at least two (2) years.
Equipment Specifications All equipment must meet the contract specifications and all federal and State safety codes and regulations in effect at the date of manufacture. All equipment must be Original Equipment Manufacturer (OEM) equipment unless otherwise stated in the contract. All products, materials, supplies, replacement parts, and equipment offered and furnished must be new, of current manufacturer production, and must have been formally announced by the manufacturer as being commercially available, unless otherwise stated in this Contract.
SERVICES AND EQUIPMENT 15.01. Landlord, at its own cost and expense shall:
(a) Provide full passenger elevator service (i.e., five (5) Passenger elevator cars, subject to the provisions of Section 15.03) from 8:00 A.M. to 6:00 P.M. on all Business Days with two (2) passenger elevators available at all other times. Landlord may designate local and express stops for elevators and may change such designation of express and local stops from time to time. Landlord agrees that, except in an emergency situation, Landlord shall not grant permission for any construction items or materials or for any workmen carrying the same to be transported by use of the passenger elevator cars. At times other than during Business Hours of Business Days up to one (1) elevator car in Tenant’s elevator bank may be used for the transport of construction workers or materials; provided that such elevator car shall be properly cleaned before the beginning of the next Business Day. Landlord will use a first class standard for elevator maintenance.
(b) Provide freight elevator service to the Premises on a first come-first served basis (i.e., no advance scheduling) during the Building’s normal freight elevator hours (i.e., 8 A.M. to 12:00 P.M. and 1:00 P.M. to 4:30 P.M.) of Business Days. Freight elevator service shall also be provided to the Premises on a reserved basis at all other times, upon the payment of Landlord’s then established charges therefor which shall be Additional Charges hereunder. As of the date hereof, Landlord’s charge for overtime freight elevator service is at the rate of $200 per hour subject to increase in proportion to increases in Landlord’s actual costs to provide same. Any request for overtime freight elevator service shall entail a minimum in the number of hours to the extent the applicable Building Service Union Employee Service contract requires a minimum number of hours per shift.
(i) Supply ventilation throughout the year and supply heat and air-conditioning, as seasonally required; but in all events, Landlord shall supply heat from October 15 to April 15 and air-conditioning from April 15 to October 15, from the Building heating, ventilating and air-conditioning system from 8:00 A.M. to 6:00 P.M, on all Business Days in accordance with the specifications attached hereto as Exhibit N and made a part hereof.
(ii) In connection with its operation of the existing systems and equipment in the Building, give due consideration to the applicable portions of ASHRAE Standard No. 62-1989 to the extent that the same is implemented or adhered to generally by buildings with similar systems and equipment and of similar age and size. Tenant acknowledges that if it shall fail to keep entirely unobstructed all of the vents, intakes, outlet and grilles in the Premises at all times, or shall fail to comply with and observe all reasonable regulations and requirements prescribed by Landlord for the proper functioning of the heating, ventilating and air-conditioning system, the HVAC services may not meet the standards set forth in the specifications.
(d) Provide cleaning services, in accordance with the specifications set forth in Exhibit F hereto, in the Premises and public portions of the Building on all Business Days.
(e) Furnish hot and cold water for lavatory and drinking and office cleaning purposes and for use in all pantries and kitchenettes installed by Tenant in the Premises. If Tenant requires, uses or consumes water for any other purposes, Tenant agrees that Landlord may install a meter to measure Tenant’s water consumption, and Tenant further agrees to reimburse Landlord for the reasonable out-of-pocket cost of the meter and the installation thereof, and to pay for the reasonable out-of-pocket maintenance cost of said meter equipment within thirty (30) days after Landlord’s rendition of a xxxx therefor. Tenant shall reimburse Landlord for the water consumed as measured by said meter based upon the actual out-of-pocket cost to Landlord of such water, including any actual out-of-pocket costs incurred by Landlord in connection with the meter readings, and any sewer rents, and all other charges imposed by any authority, on, or measured by, the use of water within thirty (30) days after rendition of a xxxx therefor.
(f) Maintain listings on the Building directory of the names of Tenant, or its permitted subtenants, assignees or affiliates and the names of any of their officers and employees, provided that the names so listed shall not use more than Tenant’s Proportionate Share of the space on the Building directory. Tenant shall reimburse Landlord for any actual out-of-pocket costs incurred by Landlord to unaffiliated third parties in connection with changes and additions to such directory listings requested by Tenant.
(g) Repaint or retouch, as reasonably required to compensate for ordinary wear and tear and for any damage caused by Landlord, its employees, contractors and agents, all convector covers in the Premises not less frequently than once in every three (3) years; provided, however, that Tenant shall be solely responsible at its expense to remove its property and make such convectors accessible for such painting by Landlord.
(h) With respect to the Tenant named herein only, provide at the existing security/concierge desk in the lobby of the Building during all hours other than Business Hours of Business Days personnel to carry out such security procedures as are set forth in Exhibit P hereof and to implement other security measures as Landlord shall from time to time adopt (after consultation with Tenant, but without any obligation to obtain Tenant’s agreement or approval). Notwithstanding that Landlord shall agree to instruct its employees to follow such security procedures as set forth in this Lease, Landlord shall in no way be responsible for any violation of such procedures or circumvention of such Procedures as may occur from time to time at the Building and in no event shall Landlord be liable to Tenant for any loss, injury or damage to Tenant or to any other person as may result from violations or circumventions of the security procedures instituted at the Building as described in this subsection 15.01(h).
15.02. Holidays shall be deemed to mean all those dates designated as holidays by the Board of Governors of the New York Stock Exchange, in addition to dates designated as holidays by the City of New York, State of New York and/or the United States, and in addition shall also include holidays to which maintenance or service employees of the Building are entitled under their union contract or contracts.
15.03. Landlord reserves the right to interrupt, curtail or suspend the services required to be furnished by Landlord under this Article 15 when the necessity therefor arises by reason of accident, emergency, mechanical breakdown, or when required by any law, order or regulation of any Federal, state, county or municipal authority, or for any other cause beyond the reasonable control of Landlord. Except in case of an emergency, Landlord will notify Tenant in advance of any such stoppage, and if ascertainable, its estimated duration. Landlord shall complete all required repairs or other necessary work in accordance with the standards set forth in subsection 13.01(b). Except as set forth in Section 13.03 hereof and subject to the provision of Section 27.03 hereof, no diminution or abatement of rent or other compensation shall or will be claimed by Tenant as a result therefrom, nor shall this Lease or any of the obligations of Tenant be affected or reduced by reason of such interruption, curtailment or suspension.
(a) If Tenant shall require heat or air-conditioning services at any time other than as furnished by Landlord in accordance with subsection 15.01(c) hereof, then, if Tenant shall give notice in writing to the Building superintendent prior to 4:00 P.M. in the case of services required on weekdays, prior to 4:00 P.M. on the Friday prior in the case of after hours service recurred on weekends or on holiday Mondays or prior to 4:00 P.M. on the day prior in the case of after hours service recurred on other holidays or weekends following Fridays which are holidays, Landlord shall furnish such service and Tenant shall pay to Landlord upon demand as Additional Charges hereunder Landlord’s then established charges therefor. As of the date hereof, Landlord’s standard rate charged to other tenants in the Building is $600.00 per floor per hour and, except as otherwise provided below in this subsection 15.04(a), requires a four (4) hour minimum and a four (4) floor minimum. Such charge shall be subject to increase in proportion to increases in Landlord’s actual costs to provide same provided however if Landlord charges a future tenant in the Building a lesser rate for the overtime heat or air-conditioning services, then provided Tenant shall agree to be obligated to utilize the same or more overtime heat or air-conditioning services utilized by such future tenant, such charge charged to Tenant shall then and thereafter be reduced to such lesser charge charged to such future tenant. If any other tenant or tenants of the Building in the same zone as Tenant request overtime air-conditioning or heating for any period for which Tenant has requested such service pursuant to the provisions of this subsection 15.04(a), then the Landlord’s charge for overtime HVAC, as set forth above, shall be prorated among Tenant and such other tenant or tenants, as the case may be. Notwithstanding the generality of the foregoing, any request for overtime HVAC service to commence at 6:00 P.M. on any Business Day shall not require or be subject to a “minimum” with respect to hours, but shall still require a four (4) floor minimum. Notwithstanding anything to the contrary contained herein, Tenant shall be entitled to receive overtime HVAC without being required to pay any Additional Charges therefor on up to twelve (12) occasions (each such occasion being of a duration of four (4) hours and applying with respect to four (4) floors in the Premises) during each calendar year to occur during the term of this Lease (prorated on the basis of one (1) such occasion per month with respect to any partial calendar year to occur during the term of this Lease). Each such four (4) continuous hour period is
Customer Equipment Customer represents and warrants that it owns or has the legal right and authority, and will continue to own or maintain the legal right and authority during the term of this Agreement, to place and use the Customer Equipment as contemplated by this Agreement. Customer further represents and warrants that its placement, arrangement, and use of the Customer Equipment in the Internet Data Centers complies with the Customer Equipment Manufacturer's environmental and other specifications.
Accessories, Spare Parts and Tools Accessories, spare parts and tools dispatched with a piece of equipment, machine, apparatus or vehicle, which are part of the normal equipment and included in the price thereof or which are not separately invoiced, shall be regarded as one with the piece of equipment, machine, apparatus or vehicle in question.
Electrical Equipment Residents must use only CSA, UL-approved or Canadian-certified electrical equipment; the rated wattage of light fixtures must never be exceeded; and only replacement bulbs supplied by Waterloo maintenance staff may be used. Do not leave any unattended electrical equipment turned on (i.e. hair straighteners, lights etc.)
Metering The Interconnection Customer shall be responsible for the Connecting Transmission Owner’s reasonable and necessary cost for the purchase, installation, operation, maintenance, testing, repair, and replacement of metering and data acquisition equipment specified in Attachments 2 and 3 of this Agreement. The Interconnection Customer’s metering (and data acquisition, as required) equipment shall conform to applicable industry rules and Operating Requirements.
Filing Systems and Equipment A complete and comprehensive catalog of filing systems including vertical and lateral files, bookcases, mobile cabinets and freestanding file cabinets.
