SURFACE FINISHING Sample Clauses

SURFACE FINISHING. Surface finishing shall have a semi-gloss sheen, and shall be one of the following Federal Standard 595B colors: Green # 14036, Brown # 10049, Black # 27038, Grey # 26147 or as selected by the EIU.
Sample 1Sample 2Sample 3See All (4)
AutoNDA by SimpleDocs
SURFACE FINISHING. Surface finishing shall have a semi-gloss sheen, and shall be one of the following Federal Standard 595B colors: Green #14036, Brown #10049, Black #27038, Grey #26147 or as selected by the Engineer. 4.2.42.1. PAINT- All painted posts and/or painted surfaces shall be cleaned of all foreign matter, such as loose paint, rust, dirt, and grease before painting. Paint used must be of the anti-graffiti, corrosion resisting, non-conductive, semi-gloss type as manufactured by Armor Products, Inc., by BC Products International, Inc., by Con- Lux Coatings, Inc. or an approved equal. 4.2.42.1.1. Paint Characteristics: - The protective coating must exhibit the following characteristic. Exceptional resistance to ultra violet light, road salt compounds, and industrial chemical fumes. High impact resistance forward and reverse to withstand 160 psi directly without cracking, chipping, or peeling. Display a water transmission rate of less than 0.00000005 Perms. Bend over 180 degrees and 1/8" mandrel without cracking. Suitable for applications in below freezing temperatures. Resist solvents for removal of graffiti off painted surface. Resist flame or high temperatures to 400 degrees Fahrenheit. Shall possess unique molecular structure suitable for brush, roll or spray application to achieve high quality, general purpose usage, exceptional spreadability and adhesion. Exhibit corrosion resistance equal to that tested as part of Painting System #41 by the Steel Structures Painting Council.
Sample 1Sample 2
SURFACE FINISHING. 4.43.1. PAINT The Paint shall have a semi-gloss sheen, and shall be one of the following Federal Standard 595B colors: Green #14036, Brown #10049, Black #27038 or Grey #26147 or as selected by the Engineer. All painted posts and/or painted surfaces shall be cleaned of all foreign matter, such as loose paint, rust, dirt, and grease before painting. Paint used must be of the anti-graffiti, corrosion resisting, semi-gloss type as manufactured by Armor Products, Inc., by BC Products International, Inc., by Con-Lux Coatings, Inc. or an approved equal. Paint Characteristics: The protective coating must exhibit the following characteristic. Exceptional resistance to ultra violet light, road salt compounds, and industrial chemical fumes. High impact resistance forward and reverse to withstand 160 psi directly without cracking, chipping, or peeling. Display a water transmission rate of less than 0.00000005 Perms. Bend over 180 degrees and 1/8" mandrel without cracking. Suitable for applications in below freezing temperatures. Resist solvents for removal of graffiti off painted surface. Resist flame or high temperatures to 400 degrees Fahrenheit. Shall possess unique molecular structure suitable for brush, roll or spray application to achieve high quality, general purpose usage, exceptional spreadability and adhesion. Exhibit corrosion resistance equal to that tested as part of Painting System #41 by the Steel Structures Painting Council. Chemical Composition of Paint All paint must conform with the following chemical requirements: No more than 20 percent Oxal Hexel, 17 percent Butyl Acetate, 3 percent Xylol. Maximum of 40 percent volatile by volume. Minimum of 60 degrees Fahrenheit Flashpoint. Formulated with air out additives for flowability. Two part aliphatic urethane with a 3 to 1 mixture ration and an absolute minimum of 60 percent solid content. Maximum VOC of 3.45 per gallon.
Sample 1
SURFACE FINISHING. 4.43.1. PAINT The Paint shall have a semi-gloss sheen, and shall be one of the following Federal Standard 595B colors: Green #14036, Brown #10049, Black #27038 or Grey #26147 or as selected by the Engineer. All painted posts and/or painted surfaces shall be cleaned of all foreign matter, such as loose paint, rust, dirt, and grease before painting. Paint used must be of the anti-graffiti, corrosion resisting, semi-gloss type as manufactured by Armor Products, Inc. or approved equal, by BC Products International, Inc. or approved equal, by Con-Lux Coatings, Inc. or approved equal. Paint Characteristics: The protective coating must exhibit the following characteristic. Exceptional resistance to ultra violet light, road salt compounds, and industrial chemical fumes. High impact resistance forward and reverse to withstand 160 psi directly without cracking, chipping, or peeling. Display a water transmission rate of less than 0.00000005 Perms. Bend over 180 degrees and 1/8" mandrel without cracking. Suitable for applications in below freezing temperatures. Resist solvents for removal of graffiti off painted surface. Resist flame or high temperatures to 400 degrees Fahrenheit. Shall possess unique molecular structure suitable for brush, roll or spray application to achieve high quality, general purpose usage, exceptional spreadability and adhesion. Exhibit corrosion resistance equal to that tested as part of Painting System #41 by the Steel Structures Painting Council. Chemical Composition of Paint All paint must conform with the following chemical requirements: No more than 20 percent Oxal Hexel, 17 percent Butyl Acetate, 3 percent Xylol. Maximum of 40 percent volatile by volume. Minimum of 60 degrees Fahrenheit Flashpoint. Formulated with air out additives for flowability. Two part aliphatic urethane with a 3 to 1 mixture ration and an absolute minimum of 60 percent solid content. Maximum VOC of 3.45 per gallon.
Sample 1
SURFACE FINISHING 
Sample 1Sample 2

Related to SURFACE FINISHING

  • Road Surfaces (1) Grade, shape, crown, and/or outslope surface and shoulders.

  • Surface  Grade and shape the road surface, turnouts, and shoulders to the original shape on the TYPICAL SECTION SHEET. Inslope or outslope as directed to provide a smooth, rut-free traveled surface and maintain surface water runoff in an even, unconcentrated manner.  Blading shall not undercut the backslope or cut into geotextile fabric on the road.  If required by the Contract Administrator, water shall be applied as necessary to control dust and retain fine surface rock.  Surface material shall not be bladed off the roadway. Replace surface material when lost or worn away, or as directed by the Contract Administrator.  Remove shoulder berms, created by grading, to facilitate drainage, except as marked or directed by the Contract Administrator.  For roads with geotextile fabric: spread surface aggregate to fill in soft spots and wheel ruts (barrel spread) to prevent damage to the geotextile fabric.

  • Drainage Systems (1) Clear culvert inlets, outlets, and sediment catching basins.

  • FABRICATION Making up data or results and recording or reporting them.

  • Walls 12 Developer shall provide rustication patterns on all walls, except drainage headwalls, in Aesthetic 13 Area 3 in accordance with Exhibit L2.24 of the LAADCR. The final designs shall resemble these 14 simulations.

  • Excavation If any excavation shall be made upon land adjacent to or under the Building, or shall be authorized to be made, Tenant shall afford to the person causing or authorized to cause such excavation, license to enter the Premises for the purpose of performing such work as said person shall deem necessary or desirable to preserve and protect the Building from injury or damage and to support the same by proper foundations, without any claim for damages or liability against Landlord and without reducing or otherwise affecting Tenant’s obligations under this Lease.

  • Carpet Cleaning Shampooing carpets with the deep dirt extraction (steam cleaning) method per manufactures recommendations.

  • Exterior Drainage Does water stand on the property for more than 24 hours after a heavy rain? Yes No Unknown Comments Are gutters and downspouts in good repair? Yes No Unknown Comments:

  • Welding Welding and use of cutting torches or cutoff saws will be permitted only in areas that have been cleared or are free of all material capable of carrying fire. Flammable debris and vegetation must be removed from within a minimum 10-foot radius of all welding and cutting operations. A shovel and a 5-gallon standard backpack water container filled and with handpump attached shall be immediately available for use in the event of a fire start. C8.212 – MARKET-RELATED CONTRACT TERM ADDITION (11/08). The term of this contract may be adjusted when a drastic reduction in wood product prices has occurred in accordance with 36 CFR 223.52. The Producer Price Index used to determine when a drastic reduction in price has occurred is stated in A20. Purchaser will be notified whenever the Chief determines that a drastic reduction in wood product prices has occurred. If the drastic reduction criteria specified in 36 CFR 223.52 are met for 2 consecutive calendar quarters, after contract award date, Contracting Officer will add 1 year to the contract term, upon Purchaser’s written request. For each additional consecutive quarter such a drastic reduction occurs, Contracting Officer will, upon written request, add an additional 3 months to the term during Normal Operating Season, except that no single 3-month addition shall extend the term of the contract by more than one year. Contracting Officer must receive Purchaser’s written request for a market-related contract term addition before the expiration of this contract. No more than 3 years shall be added to a contract's term by market-related contract term addition unless the following conditions are met:

  • Fill, Backfill and Landscaping No soil found on Site, or transported to the Site from remote locations, which contains debris or waste or Hazardous Materials shall be used for fill, backfill or landscaping topsoil.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!