Common use of Unbundled Loop Modifications (Line Conditioning Clause in Contracts

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYE, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYE. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYE, BULLSEYE will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE is available at the location for which the ULM was requested, BULLSEYE will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE InterGlobe which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEInterGlobe, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEInterGlobe. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE InterGlobe may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE InterGlobe requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE InterGlobe will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE InterGlobe shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE InterGlobe desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEInterGlobe, BULLSEYE InterGlobe will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE InterGlobe is available at the location for which the ULM was requested, BULLSEYE InterGlobe will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE InterGlobe will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 BellSouth shall perform Line Conditioning in accordance with 47 C.F.R. 51.319(a)(1)(iii). Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. Insofar as it is technically feasible, BellSouth shall test and report troubles for all the features, functions and capabilities of conditioned copper lines, and may not restrict its testing to voice transmission only. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE US LEC which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEUS LEC, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEUS LEC. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE US LEC may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE US LEC requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE US LEC will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE US LEC shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE US LEC desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEUS LEC, BULLSEYE US LEC will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE US LEC is available at the location for which the ULM was requested, BULLSEYE US LEC will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE US LEC will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000BellSouth TR 73600. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE C.M. which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEC.M., so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYE. C.M.. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE C.M. may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE C.M. requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE C.M. will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE C.M. shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE C.M. desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEC.M., BULLSEYE C.M. will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE C.M. is available at the location for which the ULM was requested, BULLSEYE C.M. will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE C.M. will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves serve no network design purpose and that are beyond the limits set according to applicable industry standards and/or standard technical references. Absent any applicable industry standard technical reference, (e.g. Xxxxxxxxx, XXXX, XXXX, XXXX) XXX XX 00000 unbundled local loop technical specifications shall apply in a non- discriminatory manner consistent with 47 CFR 51.311(b), the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any Any copper loop being ordered by BULLSEYE AT&T AND TC SYSTEMS which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEAT&T AND TC SYSTEMS, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEAT&T AND TC SYSTEMS. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE AT&T AND TC SYSTEMS may request removal of any unnecessary and non-non- excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE AT&T AND TC SYSTEMS requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE AT&T AND TC SYSTEMS will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE shall AT&T AND TC SYSTEMS may request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE AT&T AND TC SYSTEMS desires BellSouth to condition. However, AT&T AND TC SYSTEMS is responsible for obtaining and providing to BellSouth the information necessary to complete the SI and/or the LSR for line conditioning. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEAT&T AND TC SYSTEMS, BULLSEYE AT&T AND TC SYSTEMS will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE AT&T AND TC SYSTEMS is available at the location for which the ULM was requested, BULLSEYE AT&T AND TC SYSTEMS will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE AT&T AND TC SYSTEMS will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 BellSouth shall perform line conditioning in accordance with FCC 47 C.F.R. §51.319 (a)(1)(iii). Line Conditioning is as defined in FCC 47 C.F.R. § 51.319 (a)(1)(iii)(A). Insofar as routine network modification that it is technically feasible, BellSouth regularly undertakes to provide xDSL services to its own customers. This may include shall test and report troubles for all the removal of any devicefeatures, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filtersfunctions, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose capabilities of conditioned copper lines, and that are beyond the limits set according may not restrict its testing to industry standards and/or the XxxxXxxxx XX 00000voice transmission only. 2.5.2 BellSouth will remove The line conditioning activity of load coils only coil removal on copper loops and sub-should not be limited to copper loops that are less than with only a length of 18,000 feet in lengthor less. 2.5.3 For any copper loop being ordered by BULLSEYE DeltaCom which has over 6,000 six thousand (6,000) feet of combined bridged tap will be modified, upon request from BULLSEYEDeltaCom, so that the loop will have a maximum of 6,000 six thousand (6,000) feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEDeltaCom. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop Loop that will result in a combined total of bridged tap between 2,500 two thousand five hundred (2,500) and 6,000 six thousand (6,000) feet will be performed at the rates set forth in Exhibit A of this Attachment.A. 2.5.4 BULLSEYE DeltaCom may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 zero (0) and 2,500 two thousand five hundred (2,500) feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction SC Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment.A. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE DeltaCom requests ULM on a reserved facility for a new loop Loop order, BellSouth may perform a pair change and provision a different loop Loop facility in lieu of the reserved facility with ULM if feasible. The loop Loop provisioned will meet or exceed specifications of the requested loop Loop facility as modified. BULLSEYE DeltaCom will not be charged for ULM if a different loop Loop is provisioned. For loops Loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop Loop provisioned. 2.5.8 BULLSEYE DeltaCom shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE DeltaCom desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEDeltaCom, BULLSEYE DeltaCom will submit a service inquiry SI to BellSouth. If a spare Loop facility that meets the loop Loop modification specifications requested by BULLSEYE DeltaCom is available at the location for which the ULM was requested, BULLSEYE DeltaCom will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE DeltaCom will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE EPICUS which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEEPICUS, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEEPICUS. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE EPICUS may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE EPICUS requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE XXXXXX will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE EPICUS shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE EPICUS desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEEPICUS, BULLSEYE XXXXXX will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE EPICUS is available at the location for which the ULM was requested, BULLSEYE EPICUS will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE EPICUS will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE Rent-A-Line which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYERent-A-Line, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYERent-A-Line. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE Rent-A-Line may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE Rent-A-Line requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE Rent-A-Line will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE Rent-A-Line shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE Rent-A- Line desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYERent-A-Line, BULLSEYE Rent-A-Line will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE Rent-A- Line is available at the location for which the ULM was requested, BULLSEYE Rent-A-Line will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE Rent-A-Line will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop Subloop that may diminish the capability of the Loop or Sub-loop Subloop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000standard technical references. Absent any applicable industry standard technical reference (e.g. Telcordia, NESC, ANSI, NES) BellSouth’s TR 73600 Unbundled Local Loop Technical Specifications shall apply in a non-discriminatory manner consistent with 47 CFR 51.311(b). 2.5.2 BellSouth will perform line conditioning at parity and in accordance with 47 CFR 51.319(a)(1)(iii). Insofar as technically feasible, BellSouth will test and report troubles for all features, functions and capabilities of conditioned copper lines and may not restrict its testing to voice transmission only. 2.5.3 BellSouth will remove load coils only on copper loops Loops and sub-loops Subloops that are less than 18,000 eighteen thousand (18,000) feet in lengthlength at the charge, if any, approved by the appropriate PSC. 2.5.3 2.5.4 For any copper loop being ordered by BULLSEYE Southern Digital which has over 6,000 six thousand (6,000) feet of combined bridged tap will be modified, upon request from BULLSEYESouthern Digital, so that the loop will have a maximum of 6,000 six thousand (6,000) feet of bridged tap. This modification will be performed at no additional charge to BULLSEYESouthern Digital. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop Loop that will result in a combined total of bridged tap between 2,500 two thousand five hundred (2,500) and 6,000 six thousand (6,000) feet will be performed at the rates set forth in Exhibit A of this Attachment.A. 2.5.4 BULLSEYE 2.5.5 Southern Digital may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 zero (0) and 2,500 two thousand five hundred (2,500) feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction SC Process as mutually agreed to by the Parties. 2.5.5 2.5.6 Rates for ULM are as set forth in Exhibit A of this Attachment.A. 2.5.6 2.5.7 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 2.5.8 If BULLSEYE Southern Digital requests ULM on a reserved facility for a new loop Loop order, BellSouth may perform a pair change and provision a different loop Loop facility in lieu of the reserved facility with ULM if feasible. The loop Loop provisioned will meet or exceed specifications of the requested loop Loop facility as modified. BULLSEYE Southern Digital will not be charged for ULM if a different loop Loop is provisioned. For loops Loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop Loop provisioned. 2.5.8 BULLSEYE 2.5.9 Southern Digital shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE Southern Digital desires BellSouth to condition. 2.5.9 2.5.10 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYESouthern Digital, BULLSEYE Southern Digital will submit a service inquiry SI to BellSouth. If a spare Loop facility that meets the loop Loop modification specifications requested by BULLSEYE Southern Digital is available at the location for which the ULM was requested, BULLSEYE Southern Digital will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE Southern Digital will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE Comm South which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEComm South, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEComm South. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE Comm South may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE Comm South requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE Comm South will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE Comm South shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE Comm South desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEComm South, BULLSEYE Comm South will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE Comm South is available at the location for which the ULM was requested, BULLSEYE Comm South will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE Comm South will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as a routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop subloop that may diminish the capability of the Loop or Sub-loop subloop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves serve no network design purpose and that are beyond the limits set according to industry standards and/or standards. In the XxxxXxxxx XX 00000absence of an industry standard for a BellSouth Loop type, the Loop will be provided on a nondiscriminatory basis. 2.5.2 BellSouth will remove load coils only on copper loops Loops and sub-loops subloops as requested by MCI that are less than 18,000 feet in lengthlength at the rate set forth in Exhibit A. BellSouth will remove load coils on copper Loops and subloops that are greater than 18,000 feet in length on a special construction basis. 2.5.3 For any Any copper loop Loop being ordered by BULLSEYE MCI which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEMCI, so that the loop Loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEMCI. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop Loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE MCI may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. However, should BellSouth refuse MCI’s request to condition a Loop, BellSouth will comply with the appropriate requirements of 47 CFR 51.319 (a)(1)(iii). 2.5.7 If BULLSEYE MCI requests ULM on a reserved facility for a new loop Loop order, BellSouth may perform a pair change and provision a different loop Loop facility in lieu of the reserved facility with ULM if feasible. The loop Loop provisioned will meet or exceed specifications of the requested loop Loop facility as modified. BULLSEYE MCI will not be charged for ULM if a different loop Loop is provisioned. For loops Loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop Loop provisioned. 2.5.8 BULLSEYE MCI shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE MCI desires BellSouth to condition.condition.‌‌‌ 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEMCI, BULLSEYE MCI will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop Loop modification specifications requested by BULLSEYE MCI is available at the location for which the ULM was requested, BULLSEYE MCI will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE MCI will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as a routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop subloop that may diminish the capability of the Loop or Sub-loop subloop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves serve no network design purpose and that are beyond the limits set according to industry standards and/or standards. In the XxxxXxxxx XX 00000absence of an industry standard for a BellSouth Loop type, the Loop will be provided on a nondiscriminatory basis. 2.5.2 BellSouth will remove load coils only on copper loops Loops and sub-loops subloops as requested by MCI that are less than 18,000 feet in lengthlength at the rate set forth in Exhibit A. BellSouth will remove load coils on copper Loops and subloops that are greater than 18,000 feet in length on a special construction basis. 2.5.3 For any Any copper loop Loop being ordered by BULLSEYE MCI which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEMCI, so that the loop Loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEMCI. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop Loop that will result in a Page 70 of 509 Attachment 2 Network Elements & Other Services Page 22 combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE MCI may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. However, should BellSouth refuse MCI’s request to condition a Loop, BellSouth will comply with the appropriate requirements of 47 CFR 51.319 (a)(1)(iii). 2.5.7 If BULLSEYE MCI requests ULM on a reserved facility for a new loop Loop order, BellSouth may perform a pair change and provision a different loop Loop facility in lieu of the reserved facility with ULM if feasible. The loop Loop provisioned will meet or exceed specifications of the requested loop Loop facility as modified. BULLSEYE MCI will not be charged for ULM if a different loop Loop is provisioned. For loops Loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop Loop provisioned. 2.5.8 BULLSEYE MCI shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE MCI desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEMCI, BULLSEYE MCI will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop Loop modification specifications requested by BULLSEYE MCI is available at the location for which the ULM was requested, BULLSEYE MCI will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE MCI will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE Conextel which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEConextel, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYEConextel. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE Conextel may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE Conextel requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE Conextel will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE Conextel shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE Conextel desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEConextel, BULLSEYE Conextel will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE Conextel is available at the location for which the ULM was requested, BULLSEYE Conextel will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE Conextel will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves serve no network design purpose and that are beyond the limits set according to applicable industry standards and/or standard technical references. Absent any applicable industry standard technical reference, (e.g. Xxxxxxxxx, XXXX, XXXX, XXXX) XXX XX 00000 unbundled local loop technical specifications shall apply in a non- discriminatory manner consistent with 47 CFR 51.311(b), the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any Any copper loop being ordered by BULLSEYE TCG which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYETCG, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYETCG. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE TCG may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE TCG requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE TCG will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE shall TCG may request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE TCG desires BellSouth to condition. However, TCG is responsible for obtaining and providing to BellSouth the information necessary to complete the SI and/or the LSR for line conditioning. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYETCG, BULLSEYE TCG will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE TCG is available at the location for which the ULM was requested, BULLSEYE TCG will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE TCG will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE C.M. which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYEC.M., so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYE. C.M.. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE C.M. may request removal of any unnecessary and non-excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE C.M. requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE C.M. will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE C.M. shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE C.M. desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYEC.M., BULLSEYE C.M. will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE C.M. is available at the location for which the ULM was requested, BULLSEYE C.M. will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE C.M. will not be charged for ULM but will only be charged the service order charges for submitting an order.

Unbundled Loop Modifications (Line Conditioning. 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Sub-loop that may diminish the capability of the Loop or Sub-loop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, but are not limited to, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the XxxxXxxxx XX 00000. 2.5.2 BellSouth will remove load coils only on copper loops and sub-loops that are less than 18,000 feet in length. 2.5.3 For any copper loop being ordered by BULLSEYE Lightning Communications which has over 6,000 feet of combined bridged tap will be modified, upon request from BULLSEYELightning Communications, so that the loop will have a maximum of 6,000 feet of bridged tap. This modification will be performed at no additional charge to BULLSEYELightning Communications. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper loop that will result in a combined total of bridged tap between 2,500 and 6,000 feet will be performed at the rates set forth in Exhibit A of this Attachment. 2.5.4 BULLSEYE Lightning Communications may request removal of any unnecessary and non-non- excessive bridged tap (bridged tap between 0 and 2,500 feet which serves no network design purpose), at rates pursuant to BellSouth’s Special Construction Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A of this Attachment. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If BULLSEYE Lightning Communications requests ULM on a reserved facility for a new loop order, BellSouth may perform a pair change and provision a different loop facility in lieu of the reserved facility with ULM if feasible. The loop provisioned will meet or exceed specifications of the requested loop facility as modified. BULLSEYE Lightning Communications will not be charged for ULM if a different loop is provisioned. For loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the loop provisioned. 2.5.8 BULLSEYE Lightning Communications shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that BULLSEYE Lightning Communications desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for BULLSEYELightning Communications, BULLSEYE Lightning Communications will submit a service inquiry to BellSouth. If a spare Loop facility that meets the loop modification specifications requested by BULLSEYE Lightning Communications is available at the location for which the ULM was requested, BULLSEYE Lightning Communications will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, BULLSEYE Lightning Communications will not be charged for ULM but will only be charged the service order charges for submitting an order.