Uniform Method of Determining Ability to Pay. (UMDAP) refers to the method used for determining the annual Client liability for Mental Health Services received from the County mental health system and is set by the State of California.
Uniform Method of Determining Ability to Pay Sample Clauses
Related to Uniform Method of Determining Ability to Pay
Method of Determination A determination (if required by applicable law) with respect to Indemnitee’s entitlement to indemnification shall be made, as follows: (a) if a Change in Control has occurred, unless Indemnitee shall request in writing that such determination be made in accordance with clause (b) of this Section 6.02, the determination shall be made by Independent Counsel in a written opinion to the Board, a copy of which shall be delivered to Indemnitee. (b) If a Change in Control has not occurred, and subject to Section 6.03, the determination shall be made by (i) a majority vote of the Disinterested Directors, even though less than a quorum; (ii) by a committee of Disinterested Directors designated by majority vote of such Disinterested Directors, even though less than a quorum; (iii) if there are no such Disinterested Directors, by the Independent Counsel in a written opinion to the Board, or (iv) by the Company’s stockholders.
Method of Measurement All linear and area measurements under this Agreement are measured on the horizontal plane, unless specified otherwise in an attached Schedule.
Method of Calculation All calculations under this Section 4 shall be made to the nearest one hundredth of a share.
Method of Computation To determine the Adviser’s liability with respect to the Excess Amount, each month the Fund Operating Expenses for the Fund shall be annualized as of the last day of the month. If the annualized Fund Operating Expenses for any month exceeds the Operating Expense Limit of the Fund, the Adviser shall first waive or reduce its investment advisory fee for such month by an amount sufficient to reduce the annualized Fund Operating Expenses to an amount no higher than the Operating Expense Limit. If the amount of the waived or reduced investment advisory fee for any such month is insufficient to pay the Excess Amount, the Adviser shall also remit to the Fund an amount that, together with the waived or reduced investment advisory fee, is sufficient to pay such Excess Amount.
Service Providing Methodology 1.3.1 Party A and Party B agree that during the term of this Agreement, where necessary, Party B may enter into further service agreements with Party A or any other party designated by Party A, which shall provide the specific contents, manner, personnel, and fees for the specific services. 1.3.2 To fulfill this Agreement, Party A and Party B agree that during the term of this Agreement, where necessary, Party B may enter into equipment or property leases with Party A or any other party designated by Party A which shall permit Party B to use Party A’s relevant equipment or property based on the needs of the business of Party B. 1.3.3 Party B hereby grants to Party A an irrevocable and exclusive option to purchase from Party B, at Party A’s sole discretion, any or all of the assets and business of Party B, to the extent permitted under PRC law, at the lowest purchase price permitted by PRC law. The Parties shall then enter into a separate assets or business transfer agreement, specifying the terms and conditions of the transfer of the assets.
Method of Compensation It is understood by the parties that, insofar as pay is concerned, employees temporarily filling a position in a higher broadband level shall be paid according to the same compensation method as promoted employees pursuant to the Rules of the State Personnel System.
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C. 1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.
Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
