Urinals. Unit must have a wall mounted urinal. Urinals are not required in ADA units.
Urinals a. Urinals shall be lipped type half stall white glazed vitreous China of approximate Size 630 x 420 x 380 mm size.
Urinals. 4.3.1. Half stall wall hung urinals of glazed vitreous china shall be provided with 15mm dia, C.P. brass spreader, 32mm dia C.P. domical waste and C.P. cast brass P Shaped trap (if in built water sealed provision not provided) with pipe and wall flange and shall fixed to wall by one C.I. bracket and two C.I. clips as recommended by manufacturers complete as directed by the Client’s Representative.
Urinals. Clean all urinals with a toilet bowl brush and disinfectant cleaner. Damp wipe all sides and undersides of urinals. Clean and dry all chrome fixtures. Remove graffiti. Eliminate urine, fecal, and other unacceptable odors.
Urinals. Shall be vitreous china washout type, wall hung, flush-o-meter valve type, 1.0 gallon flush, with carrier.
Urinals. The urinal shall be flat back or angular pattern lipped from basin of required dimensions of white/approved colour vitreous china and one piece construction with integral flushing box rim of an approved make as specified. It shall be fixed in the position by using wooden plug embedded in the wall with screws of proper size. The size of wooden plugs shall be 50mmx50mm at base tapering to 38mmx38mm at top and length of 5.0cms. These shall be fixed in the wall in cement mortar 1:3. After the plug fixed in the wall, the mortar shall be cured till it set. Each urinal shall be connected to a 32mm diameter PVC waste pipe unless otherwise specified, which shall discharge into a channel or approved trap as specified or shown in drawings. The connection between the urinal and flush or waste pipe shall be made by means of white lead mixed with chopped hemp. The flush pipe and waste pipe shall be concealed where directed. The inlet water supply pipe to the urinal shall be GI pipe of 15mm nominal bore concealed in the wall and provided with a 15mm wheel valve as shown in the drawing. Payment Payment of urinals shall be on unit basis. Rate quoted shall include cost of urinals, inlet and outlet pipes, wheel valve, breaking and making good the walls and flooring, making inlet and outlet connections, painting exposed brackets and GI pipes etc. all complete. Wash basins This shall be rectangle shape with one tap hole conforming to IS:2556 Part-IV. Wash basins shall be of one-piece construction including a combined overflow. A slot type of overflow having an area of not less than 5 Sq. cm. shall be provided in the front or back of the bowl and it shall be so designed as to facilitate cleaning of the overflow. This shall be fitted on C.I or MS fabricated brackets to suit the fixing of the wash basins. Brackets shall conform to IS:775. The brackets shall be given two coats of white enamel paint or Aluminium paint, over a coat of primer. The wall side shall be fixed well flushed with the plaster of wall and the joint if any, shall be properly stopped with mortar and painted white. One pillar cock, angular stop cock, PVC connecting pipe with brass union, a CP brass bottle trap with union, CP brass chain and rubber PVC stopper, 32mm dia. PVC waste pipe shall also be supplied and fitted with the wash basin and connected to the trap as per the drawing. The top of rim of the wash basin shall be fixed at 800mm above finished floor level, unless otherwise specified. Payment Payment sh...
Urinals. To be as Twyfords 'Xxxxxxx' or equivalent, white vitreous china bowl urinal complete with chrome plated strainer. A suitably sized white vitreous china cistern to BS 1876 : 1972 including syphon and drip tap is to be provided. Stainless steel flush pipe with spreader and clip is required between the cistern and the bowl. Each set of urinals to be fitted with a flushing control device such as a cistermiser or equivalent.
Urinals. Type size and shape of the urinal will be as specified in schedule “A” and shall confirm to IS - 2556 (Part–VI) section 1. The bottom of the pan shall have sufficient slope from the front towards the outlet shall be provided. When installed there should be no liquid left over in the bottom of the pan of the urinal after flushing. Each urinal shall be provided with not less than two fixing holes on each side. Each urinal shall have an integral flushing rim of suitable type and inlet or supply horn for connecting flush pipe. The flushing rim and inlet shall be of the self draining type.
Urinals. Wall mounted, low consumption, flush valve, white, vitreous china (if any).
Urinals iv. Separate toilets for ladies and gents duly making one of the toilets disabled friendly.
