Duct Insulation definition

Duct Insulation means mineral fiber batt and blanket thermal insulation with a membrane which has a frame spread classification of no more than 25 when tested in accordance with ASTM Designation E 84-77.
Sample 1Sample 2Sample 3
Duct Insulation. “HVAC Equipment Insulation”
Sample 1

Examples of Duct Insulation in a sentence

  • Pipe Insulation : Rigid Polyurethane Foam (PUF) Drain Pipe Insulation : Polyethylene Foam (Kinney Foam) Duct Insulation : Resin Bonded glass wool Acoustic Treatment : Resin Bonded glass wool Equipment Insulation : Expanded Polystyrene (SE) (EP).

  • Comply with requirements in "Duct Insulation Schedule, General," "Indoor Duct and Plenum Insulation Schedule," and "Aboveground, Outdoor Duct and Plenum Insulation Schedule" articles for where insulating materials shall be applied.

  • Duct Insulation, Duct Sealing and Air SealingAll HVAC ductwork, including plenums, shall be repaired, sealed and properly supported, according to Section D.2 “MANUFACTURED HOME – HVAC DUCTS”, before underfloor insulation is installed.

  • The Environmental A/E shall perform architectural or engineering services under the A/E Agreement and coordinate all services with the Owner’s Construction Manager-At-Risk for the following project: Abatement of Lead and Asbestos as required for the work in buildings 518, 718, 673, and 679, unit 6, as follows: No Asbestos Remediation No Lead Abatement Required AC Duct Insulation Mastic, 2nd Floor Domestic Water Pipe & fitting Insulations.

  • The whole setup was wrapped with insulation materials (Duct Insulation, Foil and Fiberglass, Frost King® All Season).Saturated aqueous solution was prepared by dissolving pure crystals of these chemicals in de-ionized water for several days followed by filtration through a 0.7 µm glass fiber filter (Whatman).

  • All accessible ducts in unconditioned attic areas shall be sealed, supported, mechanically fastened, and insulated in compliance with Section D.1. – HVAC Duct Insulation & Sealing when installing attic insulation.

  • The specimen preparation and mounting procedures of ASTM E 2231, Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics, shall be used.

  • There was not enough information to perform Illinois Statewide TRM calculations for Duct Sealing and Duct Insulation.

  • Unless otherwise specified measurement for duct insulation for the project will be on the basis of centre line measurements described herewith: Duct Insulation and Acoustic Lining:Duct insulation and acoustic lining will be measured on the basis of surface area of the duct including cladding, tapered pieces, bends, tees, branches, etc.

  • Installing ductwork in spaces in which the temperature is regulatedwill significantly decrease temperature loss within the ducts in a home.• Duct Insulation: If ductwork is placed in rooms where the temperature is controlled, the need for duct insulation is reduced; however some insulation is still necessary.

Related to Duct Insulation

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Hydrofluorocarbons means compounds that only contain hydrogen, fluorine, and carbon.

  • High global warming potential hydrofluorocarbons means any hydrofluorocarbons in a particular end use for which EPA’s Significant New Alternatives Policy (SNAP) program has identified other acceptable alternatives that have lower global warming potential. The SNAP list of alternatives is found at 40 CFR Part 82 subpart G with supplemental tables of alternatives available at (http://www.epa.gov/snap/).

  • Perfluoroalkyl and polyfluoroalkyl substances or “PFAS” means a class of fluorinated organic chemicals containing at least one fully fluorinated carbon atom.

  • Explosives (1) means solid, liquid or gaseous substances or mixtures of substances which, in their application as primary, booster, or main charges in warheads, demolition and other applications, are required to detonate.

  • Crawling bug insecticide means any insecticide product that is designed for use against ants, cockroaches, or other household crawling arthropods, including, but not limited to, mites, silverfish or spiders. “Crawling Bug Insecticide” does not include products designed to be used exclusively on humans or animals, or any house dust mite product. For the purposes of this definition only:

  • Diesel means a distillate oil which can be used as fuel for the operation of a compression ignition engine and which has an approximate boiling temperature of between 150 °C to 400 °C;

  • Encapsulation means the application of an encapsulant.

  • Polystyrene foam adhesive means an aerosol adhesive designed to bond polystyrene foam to substrates.

  • explosive actuated fastening device means a tool that is activated by an explosive charge and that is used for driving bolts, nails and similar objects for the purpose of providing fixing;

  • Radionuclide means a radioactive element or a radioactive isotope.

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Cyanoacrylate adhesive means any adhesive with a cyanoacrylate content of at least 95% by weight.

  • chemical tanker means a ship constructed or adapted and used for the carriage in bulk of any liquid product listed in chapter 17 of the International Bulk Chemical Code;

  • combustible waste means non-biodegradable, non- recyclable, non-reusable, non-hazardous solid waste having minimum calorific value exceeding 1500 kcal/kg and excluding chlorinated materials like plastic, wood pulp, etc.;

  • Incinerator means any enclosed device that:

  • Tanks has the meaning set forth in Section 4.12(b).

  • Fluid means material or substance which flows or moves whether in a semisolid, liquid, sludge, gas, or any other form or state.

  • Solid insulator means the insulating coating of wiring harnesses, provided in order to cover and prevent the high voltage live parts from any direct contact.

  • Explosive means a chemical compound, device, or mixture:

  • PCBs means polychlorinated biphenyls.

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV < Un 44 kV. [SANS 1019]

  • Dielectric material means a material that does not conduct direct electrical current. Dielectric coatings are used to electrically isolate UST systems from the surrounding soils. Dielectric bushings are used to electrically isolate portions of the UST system (e.g., tank from piping).

  • Tank means an enclosed space which is formed by the permanent structure of a ship and which is designed for the carriage of liquid in bulk.

  • Flammable means a chemical that falls into one of the following categories:

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.