Defective Products None of the Group Companies has manufactured, sold or supplied products which are, or were, in any material respect, faulty or defective, or which do not comply in any material respect with any representations or warranties expressly made by such Group Company, or with all applicable regulations, standards and requirements.
Defective Product If Client rejects Products under Section 6.1 and the deviation is determined to have arisen from Patheon’s failure to provide the Manufacturing Services in accordance with the Specifications, cGMPs, or Applicable Laws, Patheon will credit Client’s account for Patheon’s invoice price for the defective Products. If Client previously paid for the defective Products, Patheon will promptly, at Client’s election, either: (i) refund the invoice price for the defective THIS EXHIBIT HAS BEEN REDACTED AND IS THE SUBJECT OF A CONFIDENTIAL TREATMENT REQUEST. REDACTED MATERIAL IS MARKED WITH [***] AND HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION. Products; (ii) offset the amount paid against other amounts due to Patheon hereunder; or (iii) replace the Products with conforming Products without Client being liable for payment therefor under Section 3.1, contingent upon the receipt from Client of all Active Materials and Client-Supplied Components required for the manufacture of the replacement Products. For greater certainty, Patheon’s responsibility for any loss of Active Materials in defective Product will be captured and calculated in the Active Materials Yield under Section 2.2.
Latent Defects Seller has no actual knowledge of any latent defects on, in, under or above the Land, the Lots or the Improvements (to the extent completed as of the date of this Agreement). For purposes of this representation, the actual knowledge of Seller shall mean the actual knowledge of only Xxxxxxxx X. Xxxx and no other person. 7.2
Supplier Selection If Customer selects a seat or galley supplier that is not on the Boeing recommended list, such seat or galley will become BFE and the provisions of Exhibit A, Buyer Furnished Equipment Provisions Document, of the AGTA will apply.
API A. Reliant shall supply to Cardinal Health for Manufacturing and Packaging, at Reliant’s sole cost, the API and applicable reference standards in quantities sufficient to meet Reliant’s requirements for each Product as further set forth in Article 4. Prior to delivery of any of the API or reference standard to Cardinal Health for Manufacturing and Packaging, Reliant shall provide to Cardinal Health a copy of the API Material Safety Data Sheet (“MSDS”), as amended, and any subsequent revisions thereto. Reliant shall supply the API, reference standards, and Certificate of Analysis FOB the Facility no later than thirty (30) days before the scheduled Manufacture Date upon which such API will be used by Cardinal Health. Upon receipt of the API, Cardinal Health shall conduct identification testing of the API. Cardinal Health shall use the API solely and exclusively for Manufacturing and Packaging under this Agreement. The maximum volume of API that Reliant supplies to Cardinal Health shall not exceed the amount reflected in the Firm Commitment and the next six (6) months of the Rolling Forecast.
Manufacturing Intrexon shall have the option and, in the event it so elects, shall use Diligent Efforts, to perform any manufacturing activities in connection with the Aquaculture Program that relate to the Intrexon Materials, including through the use of a suitable Third Party contract manufacturer. To the extent that Intrexon so elects, Intrexon may request that AquaBounty and Intrexon establish and execute a separate manufacturing and supply agreement, which agreement will establish and govern the production, quality assurance, and regulatory activities associated with manufacture of Intrexon Materials. Except as provided in Section 4.1, any manufacturing undertaken by Intrexon pursuant to the preceding sentence shall be performed in exchange for cash payments equal to Intrexon’s Fully Loaded Cost in connection with such manufacturing, on terms to be negotiated by the Parties in good faith. In the event that Intrexon does not manufacture Intrexon Materials or bulk quantities of other components of AquaBounty Products, then Intrexon shall provide to AquaBounty or a contract manufacturer selected by AquaBounty and approved by Intrexon (such approval not to be unreasonably withheld) all Information Controlled by Intrexon that is (a) related to the manufacturing of such Intrexon Materials or bulk qualities of other components of AquaBounty Products for use in the Field and (b) reasonably necessary to enable AquaBounty or such contract manufacturer (as appropriate) for the sole purpose of manufacturing such Intrexon Materials or bulk quantities of other components of AquaBounty Products. The costs and expenses incurred by Intrexon in carrying out such transfer shall be borne by Intrexon. Any manufacturing Information transferred hereunder to AquaBounty or its contract manufacturer shall not be further transferred to any Third Party, including any Product Sublicensee, or any AquaBounty Affiliate without the prior written consent of Intrexon; provided, however, that Intrexon shall not unreasonably withhold such consent if necessary to permit AquaBounty to switch manufacturers.
Correction of Defects To promptly correct any structural defects in the Improvements or any material departure from the Plans and Specifications not previously approved by Lessor. The advance of any Development Financing proceeds shall not constitute a waiver of Lessor's right to require compliance with this covenant.
Shipment If any of the Major Components associated with any Unit is not Shipped on or before (with the prior approval of the Buyer) the Scheduled Major Component Shipment Date set forth in Attachment 1 for reasons attributable to the Seller and not excused elsewhere in this Contract, the Seller shall pay as liquidated damages, and not as a penalty, a sum calculated in accordance with the table below for each Unit for each day of delay after the Scheduled Major Component Shipment Date as set forth in Attachment 1 until actual Shipment of the last Major Component for such Unit: Days after Scheduled Major Component Shipment Date Liquidated Damages (per day or partial day) *** *** *** *** *** *** Such liquidated damages, if any, shall be computed based on the date of Shipment of the last Major Component for a given Unit and such computations shall disregard any part of or accessory to the Major Component which may be shipped separately and arrive later unless such part of or accessory to the Major Component is necessary for the installation of the Major Component.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
Review of Materials During the term of this Agreement, Client shall ensure that all prospectuses, statements of additional information, registration statements, proxy statements, reports to shareholders, advertising and sales literature or other materials prepared for distribution to Fund shareholders or the public, which refer to the Subadviser in any way, prepared by employees or agents of Client or its affiliates are consistent with information previously provided by Subadviser. Subadviser shall promptly notify the Client of any changes to information pertaining to the Subadviser and stated in the materials described in this Section 6(g).
