Compliance with Federal Regulations (1) Any contract entered pursuant to this solicitation shall contain the following provisions: All USDOT-required contractual provisions, as set forth in FTA Circular 4220.1F, are incorporated by reference. Anything to the contrary herein notwithstanding, FTA mandated terms shall control in the event of a conflict with other provisions contained in this Agreement. Contractor shall not perform any act, fail to perform any act, or refuse to comply with any grantee request that would cause the recipient to be in violation of FTA terms and conditions. Contractor shall comply with all applicable FTA regulations, policies, procedures and directives, including, without limitation, those listed directly or incorporated by reference in the Master Agreement between the recipient and FTA, as may be amended or promulgated from time to time during the term of this contract. Contractor’s failure to so comply shall constitute a material breach of this contract.
Compliance with Federal and State Work Authorization and Immigration Laws The Contractor and all subcontractors, suppliers and consultants must comply with all federal and state work authorization and immigration laws, and must certify compliance using the form set forth in Section 7 (“Georgia Security and Immigration Compliance Act Affidavits”). The required certificates must be filed with the Owner and copied maintained by the Contractor as of the beginning date of this contract and each subcontract, supplier contract, or consultant contract, and upon final payment to the subcontractor or consultant. State officials, including officials of the Georgia Department of Audits and Accounts, officials of the Owner, retain the right to inspect and audit the Project Site and employment records of the Contractor, subcontractors and consultants without notice during normal working hours until Final Completion, and as otherwise specified by law and by Rules and Regulations of the Georgia Department of Audits and Accounts.
Compliance with Accessibility Standards All parties to this Agreement shall ensure that the plans for and the construction of all projects subject to this Agreement are in compliance with standards issued or approved by the Texas Department of Licensing and Regulation (TDLR) as meeting or consistent with minimum accessibility requirements of the Americans with Disabilities Act (P.L. 101-336) (ADA).
Compliance with Statutes The Borrower and its Subsidiaries are in compliance in all material respects with all applicable statutes, regulations and orders of, and all applicable restrictions imposed by, all governmental bodies and have all necessary permits, licenses and other necessary authorizations with respect to the conduct of their businesses and the ownership and operation of their properties except where the failure to so comply or hold such permits, licenses or other authorizations could not reasonably be expected to have a Material Adverse Effect.
Compliance with Federal Requirements Federal money will be used or may potentially be used to pay for all or part of the goods, construction or services under the Contract. The Contractor is responsible for compliance with all federal requirements imposed on the funds and accepts full financial responsibility for any requirements imposed by the Contractor’s failure to comply with federal requirements. Certification regarding Debarment, Suspension, Ineligibility, and Voluntary Exclusion. Federal money will be used or may potentially be used to pay for all or part of the work under the Contract, therefore Contractor certifies that it is in compliance with federal requirements on debarment, suspension, ineligibility and voluntary exclusion specified in the solicitation document implementing Executive Order 12549. Contractor’s certification is a material representation upon which the Contract award was based. Contingency Fees Prohibited.
Proof of Compliance with Workers’ Compensation Coverage Requirements An XXXXX form is NOT acceptable proof of workers’ compensation coverage. In order to provide proof of compliance with the requirements of the Workers’ Compensation Law pertaining to workers’ compensation coverage, a contractor shall:
Proof of Compliance with Disability Benefits Coverage Requirements In order to provide proof of compliance with the requirements of the Workers’ Compensation Law pertaining to disability benefits, a contractor shall:
Compliance with Privacy Code The parties acknowledge that the Warrant Agent may, in the course of providing services hereunder, collect or receive financial and other personal information about such parties and/or their representatives, as individuals, or about other individuals related to the subject matter hereof, and use such information for the following purposes:
Compliance with State Law The Business Associate acknowledges that by accepting the PHI from Covered Entity, it becomes a holder of medical information under the MCMRA and is subject to the provisions of that law. If the HIPAA Privacy or Security Rules and the MCMRA conflict regarding the degree of protection provided for PHI, Business Associate shall comply with the more restrictive protection requirement.
Compliance with Standards Although the standards for workmanship, material, and equipment have been selected in these specifications as a basis of reference, standards and specifications of the other bank member countries and recommendations of standards international organizations will be acceptable provided they are substantially equivalent to the designated standards and provided furthermore that the contractor submits for approval detailed specifications which he proposes to use. Reference to brand names or catalog numbers if any in these specifications have been made only for that equipment for which it has been determined that a degree of standardization is necessary to maintain certain essential features. And in certain cases such references have also been made for purposes of convenience to specify the requirements, in either case offers of alternative goods, which have similar characteristics and provide performance and quality at lease equal to those specified are acceptable. If the contractor offers materials, equipment, design calculations or tests, which conform to standards other than those specified, full details of the differences between the proposed standards and that specified in so far as they affect the design or purpose of the equipment, are to be supplied by the contractor if called upon to do so by the engineer, where required by the engineer for approval purposes, the contractor shall supply, without charge, duplicate copies of the proposed standards with English translations of the relevant portions. The contractor shall have available in his place of business (or in his supplier’s works) the relevant copies of standards or codes used for the use of the Engineer.
