Non-responsible Contractor The County may debar a Contractor if the Board of Supervisors finds, in its discretion, that the Contractor has done any of the following: (1) violated a term of a contract with the County or a nonprofit corporation created by the County, (2) committed an act or omission which negatively reflects on the Contractor’s quality, fitness or capacity to perform a contract with the County, any other public entity, or a nonprofit corporation created by the County, or engaged in a pattern or practice which negatively reflects on same, (3) committed an act or offense which indicates a lack of business integrity or business honesty, or (4) made or submitted a false claim against the County or any other public entity.
General Responsibility The Consultant shall, at all times during the Agreement, remain responsible. The Consultant agrees, if requested by the Commissioner of NYSDOT or his or her designee, to present evidence of its continuing legal authority to do business in New York State, integrity, experience, ability, prior performance, and organizational and financial capacity.
Trustee Not Responsible The Trustee shall not be responsible in any manner whatsoever for or in respect of the validity or sufficiency of this [First] Supplemental Indenture or for or in respect of the recitals contained herein, all of which are made solely by the Company and the Guarantors.
Not Responsible SAP and its licensors will not be responsible under this Agreement (i) if the Software is not used in accordance with the Documentation; or (ii) if the defect or liability is caused by Licensee, a Modification or Add-on (other than a Modification or Add-on made by SAP which is provided through SAP Support or under warranty), or third-party software; or (iii) if the Software is used in conjunction with any third party software for which the Licensee lacks sufficient rights from the third party vendor for such use; or (iv) for any Licensee activities not permitted under this Agreement. SAP AND ITS LICENSORS SHALL NOT BE LIABLE FOR ANY CLAIMS OR DAMAGES ARISING FROM INHERENTLY DANGEROUS USE OF THE SOFTWARE AND/OR THIRD-PARTY SOFTWARE LICENSED HEREUNDER.
Engineers Responsibility The Engineer shall be responsible for the accuracy of its work and shall promptly make necessary revisions or corrections resulting from its errors, omissions, or negligent acts without compensation. The Engineer will not be relieved of the responsibility for subsequent correction of any such errors or omissions or for clarification of any ambiguities until after the construction phase of the project has been completed.
Union Responsibility The Union will attend to any necessary documentation required as a result of a change in the designated institution.
MUTUAL RESPONSIBILITY 6.2.1 The Contractor shall afford the State and separate contractors reasonable opportunity for the introduction and storage of their materials and equipment and the execution of their work, and shall connect and coordinate his / her Work with the work of the State and separate contractors as required by the Contract Documents.
6.2.2 If any part of the Contractor's Work depends for proper execution or results upon the work of the State or any separate contractor, the Contractor shall, prior to proceeding with the Work, promptly report to the Architect any apparent discrepancies or defects in such other work that render it unsuitable for such proper execution and results. Failure of the Contractor so to report shall constitute an acceptance of the State's or separate contractors work as fit and proper to receive
6.2.3 Any costs caused by defective or ill-timed work shall be borne by the party responsible therefor.
6.2.4 Should the Contractor wrongfully cause damage to the work or property of the State, or to other work on the site, the Contractor shall promptly remedy such damage as provided in Subparagraph 10.2.5 of these General Conditions.
Seller’s Responsibility If the Seller determines that the Interface Problem is primarily attributable to the design of a Warranted Part, the Seller shall, if so requested by the Buyer and pursuant to the terms and conditions of Clause 12.1, correct the design of such Warranted Part to the extent of the Seller’s obligation as defined in Clause 12.1.
Joint Responsibility If the Seller determines that the Interface Problem is attributable partially to the design of a Warranted Part and partially to the design of any Supplier Part, the Seller will, if so requested by the Buyer, seek a solution to the Interface Problem through cooperative efforts of the Seller and any Supplier involved. The Seller will promptly advise the Buyer of such corrective action as may be proposed by the Seller and any such Supplier. Such proposal will be consistent with any then existing obligations of the Seller hereunder and of any such Supplier towards the Buyer. Such corrective action, unless reasonably rejected by the Buyer, will constitute full satisfaction of any claim the Buyer may have against either the Seller or any such Supplier with respect to such Interface Problem.
Reporting Responsibility a) Vendor shall be responsible for reporting all services purchased under the Contract. Vendor shall file the monthly reports, subcontract reports, and pay the administrative fees in accordance with the due dates specified in this section.
b) DIR shall have the right to verify required reports and to take any actions necessary to enforce its rights under this section, including but not limited to compliance checks of Vendor’s applicable Contract. Vendor will provide all required documentation at no cost.
