Felling, Bucking, Brushing and Limbing Plans Sample Clauses

Felling, Bucking, Brushing and Limbing Plans. ‌ Apply the following planning logic (OHLEC) to all phases of saw operations: Objective‌ Regardless of task, develop a plan to determine where you want the cut piece to end up. • If felling, plan the most desirable placement or lay for the tree • If bucking, plan where you want the bucked log or round to go • If limbing, determine sequence and direction for large branches when cut • If brushing, particularly in thick brush, plan how you will remove the brush when it is cut 8 (29 CFR 1910.266(d)(5)) Hazards/obstacles‌ Develop a plan to identify the hazards/obstacles: • That are overhead (fire, rotten top, widow makers and loose bark) • That are in the piece of wood being cut (fire, rot and hinge wood integrity, hollow, bar/saw length compared to diameter, bees or poison plants) • Springpoles • Buildings, equipment or other trees you don’t want damaged • That are associated with people and cutting area control Leans/binds‌ Since lay, cut piece placement, sequence or removal was determined in O develop a plan to: • Determine lean of a standing tree and calculate, in feet, the amount of head/back lean and side lean • Determine binds in log to be bucked, springpoles, limbs or brush to be removed Escape routes‌ Since leans and binds were determined in the previous step develop a plan to: • Determine the ‘good’ and ‘bad’ side of the tree, log, springpole, limb or brush • Determine and clear an escape route (or 2 routes if necessary for crosscut saw/axe work or situations that require two routes) Cut Plan‌ Develop a cut plan to determine which technique will be used to remove wood fiber to achieve the desired result including: • Face notch construction type (conventional, Humboldt or open face) • Hinge position, length of hinge, depth of hinge and amount of xxxxx shot needed • Back cut type (straight in from the back or chase, boring back cut and out the back, boring back cut with release or holding wood or strap) • Wedge placement including number of wedges and axe placement • Xxxxxx communication to crew members, swamper or crosscut xxxxxx partner
Sample 1
AutoNDA by SimpleDocs

Related to Felling, Bucking, Brushing and Limbing Plans

  • Switching and Tagging Rules The Developer and Connecting Transmission Owner shall each provide the other Party a copy of its switching and tagging rules that are applicable to the other Party’s activities. Such switching and tagging rules shall be developed on a nondiscriminatory basis. The Parties shall comply with applicable switching and tagging rules, as amended from time to time, in obtaining clearances for work or for switching operations on equipment.

  • Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.

  • CUTTING AND PATCHING The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.

  • Alignment with Modernization Foundational Programs and Foundational Capabilities The activities and services that the LPHA has agreed to deliver under this Program Element align with Foundational Programs and Foundational Capabilities and the public health accountability metrics (if applicable), as follows (see Oregon’s Public Health Modernization Manual, (xxxx://xxx.xxxxxx.xxx/oha/PH/ABOUT/TASKFORCE/Documents/public_health_modernization_man ual.pdf): a. Foundational Programs and Capabilities (As specified in Public Health Modernization Manual) b. The work in this Program Element helps Oregon’s governmental public health system achieve the following Public Health Accountability Metric, Health Outcome Measure: c. The work in this Program Element helps Oregon’s governmental public health system achieve the following Public Health Accountability Metric, Local Public Health Process Measure:

  • Proposed Policies and Procedures Regarding New Online Content and Functionality By October 31, 2017, the School will submit to OCR for its review and approval proposed policies and procedures (“the Plan for New Content”) to ensure that all new, newly-added, or modified online content and functionality will be accessible to people with disabilities as measured by conformance to the Benchmarks for Measuring Accessibility set forth above, except where doing so would impose a fundamental alteration or undue burden. a) When fundamental alteration or undue burden defenses apply, the Plan for New Content will require the School to provide equally effective alternative access. The Plan for New Content will require the School, in providing equally effective alternate access, to take any actions that do not result in a fundamental alteration or undue financial and administrative burdens, but nevertheless ensure that, to the maximum extent possible, individuals with disabilities receive the same benefits or services as their nondisabled peers. To provide equally effective alternate access, alternates are not required to produce the identical result or level of achievement for persons with and without disabilities, but must afford persons with disabilities equal opportunity to obtain the same result, to gain the same benefit, or to reach the same level of achievement, in the most integrated setting appropriate to the person’s needs. b) The Plan for New Content must include sufficient quality assurance procedures, backed by adequate personnel and financial resources, for full implementation. This provision also applies to the School’s online content and functionality developed by, maintained by, or offered through a third-party vendor or by using open sources. c) Within thirty (30) days of receiving OCR’s approval of the Plan for New Content, the School will officially adopt, and fully implement the amended policies and procedures.

  • Green Economy/Carbon Footprint a) The Supplier/Service Provider has in its bid provided Transnet with an understanding of the Supplier’s/Service Provider’s position with regard to issues such as waste disposal, recycling and energy conservation.

  • Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction. (b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.

  • TRAINING AND EMPLOYEE DEVELOPMENT 9.1 The Employer and the Union recognize the value and benefit of education and training designed to enhance an employee’s ability to perform their job duties. Training and employee development opportunities will be provided to employees in accordance with Employer policies and available resources. 9.2 Attendance at employer-required training will be considered time worked. The Employer will make reasonable attempts to schedule employer-required training during an employee’s regular work shift. The Employer will pay the registration and associated travel costs in accordance with Article 23, Travel, for employer-required training.

  • Vendor Encouraging Members to bypass TIPS agreement Encouraging entities to purchase directly from the Vendor or through another agreement, when the Member has requested using the TIPS cooperative Agreement or price, and thereby bypassing the TIPS Agreement is a violation of the terms and conditions of this Agreement and will result in removal of the Vendor from the TIPS Program.

  • Transfer and Seniority Outside the Bargaining Unit (a) It is understood that an employee shall not be transferred by the Hospital to a position outside the bargaining unit without his consent except in the case of temporary assignments not exceeding six (6) months. Such employees on temporary assignments shall remain members of the bargaining unit. (b) An employee who is transferred to a position outside the bargaining unit shall not, subject to (c) below, accumulate seniority. In the event the employee is returned by the Hospital to a position in the bargaining unit within twenty-four (24) months of the transfer he or she shall be credited with the seniority held at the time of transfer and resume accumulation from the date of his or her return to the bargaining unit. An employee not returned to the bargaining unit within 24 months shall forfeit bargaining unit seniority. (c) In the event an employee transferred out of the bargaining unit under (b) above is returned to the bargaining unit within a period of six (6) calendar months, he shall accumulate seniority during the period of time outside the bargaining unit."

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!