Filling and Finishing. Catalent shall be responsible for filling and finishing of the Lead DMD Product, which shall be performed in accordance with the Specifications, cGMPs, applicable Laws and Regulatory Acts, and the Quality Agreement.
Filling and Finishing Sample Clauses
Related to Filling and Finishing
Packing and Marking All material and equipment to be furnished by the Contractor shall be packed, crated or otherwise suitably protected to withstand shipment undamaged to the destination. Each package, crate or part shall be marked plainly with the name of the consignee, shipping destination, the Owner's order number, and such other markings as are required. Complete packing lists, one copy with each package and two (2) copies by mail to the Owner at time of shipment, shall be supplied showing contents and identity of each package.
CUTTING AND PATCHING The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.
Skidding and Yarding Methods of skid- ding or yarding specified for particular areas, if any, are indicated on Sale Area Map. Outside Clearcutting Units and construction clearings, insofar as ground conditions permit, products shall not be skidded against reserve trees or groups of reproduction and tractors shall be equipped with a winch to facilitate skidding. B6.421 Rigging. Insofar as practicable, needed rigging shall be slung on stumps or trees desig- nated for cutting.
Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction. (b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.
Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Posting and Filling of Vacancies 8.1(1) When a permanent vacancy occurs within a classification covered by this agreement, which the Employer intends to fill, after the Employer applies the internal job transfer bidding procedure and the ultimate vacancy is thereby identified, such vacancy shall be advertised for ten (10) calendar days provided that nothing herein shall prevent the Employer from advertising such vacancy throughout its system or outside during the ten (10) day period. Probationary employees may, at the sole discretion of the Employer, be considered for another position outside their classification after the signing date of this agreement. The Company reserves the sole and absolute right to carry out any applicable interviewing or testing that is necessary in its opinion. All test processes will be approved by qualified Human Resources staff. An employee will only be allowed to take one test failure for each different job classification bid every four (4) months. Current employees applying for positions which involve increased driving responsibilities must meet corporate driving standards and provide with application a current driving abstract. The opinion of the Employer shall not be exercised in an arbitrary or discriminatory manner. 8.1(2) Internal Job Transfer Bidding Procedure 8.1(3) This internal job transfer bidding procedure is within a given classification as follows: 8.1(4) All employees within each classification, when requested, must submit a “standing application” to transfer to any existing alternate home base or location, shift, shift hours, days off (in order of preference), to transfer from part-time to full-time status, or to indicate that they wish no change, whichever is applicable to each individual within their current classification. 8.1(5) A copy of such standing application submitted will be furnished to the employee. Since a standing application will remain valid indefinitely until it results in action or is replaced by the employee, it is the responsibility of the employee to ensure that a standing application always reflects the employee’s current preferences. 8.1(6) (i) When a permanent classification position vacancy is to be filled, all standing applications will immediately be reviewed with the intention of awarding transfers (including any “resultant” transfers) in order of classification seniority in the following sequence, where applicable: (a) transfer of a full-time employee from one home base or location to another or as referred to above; (b) transfer of an employee from part-time to full- time status; (c) transfer of part-time employees from one home base or location to another or as referred to above; and (d) transfer of full-time employees to part-time.
Manufacturing and Marketing Rights The Company has not granted rights to manufacture, produce, assemble, license, market, or sell its products to any other person and is not bound by any agreement that affects the Company's exclusive right to develop, manufacture, assemble, distribute, market, or sell its products.
Sealing and Marking of Bids The bidder shall seal the original and each copy of the bid in separate envelopes duly marking the envelopes “ORIGINAL” and “COPY”. The envelopes shall then be sealed in an outer separate envelope.
PACKING AND SHIPMENT (a) Unless otherwise specified, all Work is to be packed in accordance with good commercial practice. (b) A complete packing list shall be enclosed with all shipments. SELLER shall mark containers or packages with necessary lifting, loading, and shipping information, including the LOCKHEED XXXXXX Contract number, item number, dates of shipment, and the names and addresses of consignor and consignee. Bills of lading shall include this Contract number. (c) Unless otherwise specified, delivery shall be FOB Place of Shipment.
Promotion and Marketing For the purpose of promotion and marketing, the Borrower hereby authorizes and consents to the reproduction, disclosure and use by the Lenders and the Agent of its name, identifying logo and the Facilities. The Borrower acknowledges and agrees that the Lenders shall be entitled to determine, in their sole discretion, whether to use such information; that no compensation will be payable by the Lenders or the Agent in connection therewith; and that the Lenders and the Agent shall have no liability whatsoever to it or any of its employees, officers, directors, affiliates or shareholders in obtaining and using such information as contemplated herein.
