Common use of Fittings Clause in Contracts

Fittings. 1.7.3.1. The supports must be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conducive to the collection of water. 1.7.3.2. The base of the container must be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base must give the container sufficient stability. The top edge of the base must be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates must be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures must be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports must shall be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conducive conductive to the collection of water. 1.7.3.2. The base of the container must shall be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base must shall give the container sufficient stability. The top edge of the base must shall be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark xxxx shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates must shall be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures must shall be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports must be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conducive to the collection of water. 1.7.3.2. The base of the container must be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base must give the container sufficient stability. The top edge of the base must be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark xxxx shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates must be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures must be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.

Fittings. 1.7.3.1. The supports must shall be manufactured and attached to the container body in such a way as not to cause dangerous concentrations of stresses or be conducive conductive to the collection of water. 1.7.3.2. The base of the container must shall be sufficiently strong and made of metal compatible with the type of steel used for the container. The form of the base must shall give the container sufficient stability. The top edge of the base must shall be welded to the container in such a way as not to be conducive to the collection of water nor to allow water to penetrate between the base and the container. 1.7.3.3. A reference mark shall be affixed on the containers to ensure their correct installation. 1.7.3.4. Where fitted, identification plates must shall be fixed on to the stress resistant shell and shall not be removable. All the necessary corrosion prevention measures must shall be taken. 1.7.3.5. The container shall have provisions to mount a gas-tight housing or kind of protection device over the container accessories. 1.7.3.6. Any other material, however, may be used for the manufacture of the supports, provided that its strength is assured and that all risk of the container end corroding is eliminated.