Flextime (a) For the purpose of this Agreement, flextime means the hours worked by an employee, or group of employees, who are given authority by the Employer to:
ATM Card If approved, you may use your card and personal identification number (PIN) in automated teller machines (ATMs) of the Credit Union, Instant Cash, and Cirrus® networks, and such other machines or facilities as the Credit Union may designate. For ATM transactions, you must consent to the Credit Union’s overdraft protection plan in order for the transaction amount to be covered under the plan. Without your consent, the Credit Union may not authorize and pay an overdraft resulting from these types of transactions. Services and fees for ATM overdrafts are shown in the document the Credit Union uses to capture the member’s opt-in choice for overdraft protection and the Schedule of Fees and Charges. At the present time, you may use your card to: - Make deposits to your savings and checking accounts. - Withdraw funds from your savings and checking accounts. - Transfer funds from your savings and checking accounts. - Obtain balance information for your savings and checking accounts. - Make point-of-sale (POS) transactions with your card and personal identification number (PIN) to purchase goods or services at POS terminals that carry Instant Cash, and Cirrus® network logo(s). - Access your Overdraft Protection account. The following limitations on ATM Card transactions may apply: - There is no limit on the number of cash withdrawals you may make in any one (1) day. - You may withdraw up to a maximum of $500.00 in any one (1) day, if there are sufficient funds in your account. - There is no limit on the number of POS transactions you may make in any one (1) day. - For security purposes, there are other limits on the frequency and amount of transfers available at ATMs. - You may transfer up to the available balance in your accounts at the time of the transfer. - See Section 2 for transfer limitations that may apply to these transactions. Because of the servicing schedule and processing time required in ATM operations, there may be a delay between the time a deposit (either cash or check) is made and when it will be available for withdrawal.
Catalog Information about Community Regional Medical Center – Diagnostic Medical Sonography Program (CRMC-DMSP) is published in a school catalog that contains a description of certain policies, procedures, and other information about the school. CRMC-DMSP reserves the right to change any provision of the catalog at any time. Notice of changes will be communicated in a revised catalog, an addendum or supplement to the catalog, or other written format. Students are expected to read and be familiar with the information contained in the school catalog, in any revisions, supplements and addenda to the catalog, and with all school policies. By enrolling in CRMC-DMSP, the Student agrees to abide by the terms stated in the catalog and all school policies.
Destination CSU-Pueblo scholarship This articulation transfer agreement replaces all previous agreements between CCA and CSU-Pueblo in Bachelor of Science in Physics (Secondary Education Emphasis). This agreement will be reviewed annually and revised (if necessary) as mutually agreed.
Rubric The rubrics are a scoring tool used for the Educator’s self-assessment, the formative assessment, the formative evaluation and the summative evaluation. The districts may use either the rubrics provided by ESE or comparably rigorous and comprehensive rubrics developed or adopted by the district and reviewed by ESE.
Software Title and ownership to Existing Software Product(s) delivered by Contractor under the Contract that is normally commercially distributed on a license basis by the Contractor or other independent software vendor proprietary owner (“Existing Licensed Product”), embedded in the Custom Products, shall remain with Contractor or the proprietary owner of other independent software vendor(s) (ISV). Effective upon acceptance, such Product shall be licensed to Authorized User in accordance with the Contractor or ISV owner’s standard license agreement, provided, however, that such standard license, must, at a minimum: (a) grant Authorized User a non-exclusive, perpetual license to use, execute, reproduce, display, perform, adapt (unless Contractor advises Authorized User as part of Contractor’s proposal that adaptation will violate existing agreements or statutes and Contractor demonstrates such to the Authorized User’s satisfaction) and distribute Existing Licensed Product to the Authorized User up to the license capacity stated in the Purchase Order or work order with all license rights necessary to fully effect the general business purpose(s) stated in the Bid or Authorized User’s Purchase Order or work order, including the financing assignment rights set forth in paragraph (c) below; and (b) recognize the State of New York as the licensee where the Authorized User is a state agency, department, board, commission, office or institution. Where these rights are not otherwise covered by the ISV’s owner’s standard license agreement, the Contractor shall be responsible for obtaining these rights at its sole cost and expense. The Authorized User shall reproduce all copyright notices and any other legend of ownership on any copies authorized under this clause. Open source software is developed independently of Contractor and may be governed by a separate license (“open source software”). If the open source software is governed by a separate License and provided under this Contract, Contractor shall provide a copy of that license in the applicable Documentation and the Authorized User's license rights and obligations with respect to that open source software shall be defined by those separate license terms and subject to the conditions, if any, therein. Nothing in this Contract shall restrict, limit, or otherwise affect any rights or obligations the Authorized User may have, or conditions to which the Authorized User may be subject, under such separate open source license terms.
Television Equipment Recycling If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.
TOOL STORAGE 1. A company shall provide on all construction jobs in towns and cities, and elsewhere where reasonably necessary and practicable (or if requested buy the employee), a suitable and secure waterproof lock-up solely for the purpose of storing employees’ tools, and on multi-storey and major projects the company shall provide, where possible, a suitable lock-up for employees’ tools within a reasonable distance of the work area of large groups of employees.
Flexible Work Arrangements (1) Work-life strategies are important to allow staff to harmonise their family and work commitments, while maintaining operational efficiency and work force productivity.
Television Equipment Recycling Program If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.
