Fuel Gas Analysis Sample Clauses

Fuel Gas Analysis. Six fuel gas samples will be collected during each one-hour test period. Shell shall ensure that three samples from each hour will be analyzed and the other three will be held by the Owner as backup samples. Fuel gas sampling will be performed at a convenient location such as the connection for pressure indicator upstream of the Plant orifice flow meter or other sample or vent connection in the upper hemisphere of the pipe. Shell shall ensure that stainless steel fuel sampling containers and appropriate connections will be provided by Owner. Sampling procedures will be in accordance with [7]. Each sample will be clearing labeled with an identification number, project name, date, time, name of the person acquiring the sample, and the words “Methane, Compressed.” Shell shall cause Owner to identify an independent authority to analyze the fuel gas samples, subject to mutual approval. The analysis will be performed in accordance with [9], [10], and [12], and will result in a report of constituting analysis (including chromatography charts showing peaks), lower and higher heating values (on a mass and volumetric basis), specific gravity, compressibility, and viscosity for each sample. Standard conditions should be specified as 60°F and 14.696 psia. In addition, the associated measurement uncertainties and quality assurance procedures should be provided by the laboratory. Fuel gas properties at flow meter process conditions for the flow equations will be determined from the laboratory analysis and hydrocarbon mixture calculations based on [11], [16], and [17]. A permanent Plant chromatograph will be in service at the on-site Transco and SONAT monitoring stations upstream of the Plant orifice meter as a source of secondary fuel constituent data. The chromatograph analysis of ten (10) constituents plus heating value and specific gravity will be available as a local output as well as in the DCS. Calibration cycles will be set as necessary to maximize the accuracy of the chromatograph. Sampling/analysis results will be updated approximately every five to ten minutes.
Sample 1
AutoNDA by SimpleDocs

Related to Fuel Gas Analysis

  • Risk Analysis The Custodian will provide the Fund with a Risk Analysis with respect to Securities Depositories operating in the countries listed in Appendix B. If the Custodian is unable to provide a Risk Analysis with respect to a particular Securities Depository, it will notify the Fund. If a new Securities Depository commences operation in one of the Appendix B countries, the Custodian will provide the Fund with a Risk Analysis in a reasonably practicable time after such Securities Depository becomes operational. If a new country is added to Appendix B, the Custodian will provide the Fund with a Risk Analysis with respect to each Securities Depository in that country within a reasonably practicable time after the addition of the country to Appendix B.

  • Sampling and Analysis The sampling and analysis of the coal delivered hereunder shall be performed by Buyer upon delivery of the coal to Buyer’s facility, and the results thereof shall be accepted and used as defining the quality and characteristics of the coal delivered under this Agreement and as the Payment Analysis. All analyses shall be made in Buyer’s laboratory at Buyer’s expense in accordance with ASTM standards where applicable, or industry-accepted standards in other cases. Samples for analyses shall be taken in accordance with ASTM standards or other methods mutually acceptable to both parties. Seller shall transmit its “as loaded” quality analysis to Buyer as soon as possible. Seller’s “as-loaded” quality shall be the Payment Analysis only when Buyer’s sampler and/or scales are inoperable, or if Buyer fails to obtain a sample upon unloading. Seller represents that it is familiar with Buyer’s sampling and analysis practices, and that it finds them to be acceptable. Buyer shall notify Seller in writing of any significant changes in Buyer’s sampling and analysis practices. Any such changes in Buyer’s sampling and analysis practices shall, except for ASTM or industry-accepted changes in practices, provide for no less accuracy than the sampling and analysis practices existing at the tune of the execution of this Agreement, unless the Parties otherwise mutually agree. Each sample taken by Buyer shall be divided into four (4) parts and put into airtight containers, properly labeled and sealed. One (1) part shall be used for analysis by Buyer. One (1) part shall be used by Buyer as a check sample, if Buyer in its sole judgment determines it is necessary. One (1) part shall be retained by Buyer until thirty (30) days after the sample is taken (“Disposal Date”), and shall be delivered to Seller for analysis if Seller so requests before the Disposal Date. One (1) part (the “Referee Sample”) shall be retained by Buyer until the Disposal Date. Seller shall be given copies of all analyses made by Buyer by the fifth (5th) business day of the month following the month of unloading. In addition, Buyer shall send Seller weekly analyses of coal unloaded at Buyer’s facilities. XXXXXXXXX COAL COMPANY, INC. LG&E/KU Xxxxxxxx Xx. X00000 Seller, on reasonable notice to Buyer, shall have the right to have a representative present to observe the sampling and analyses performed by Buyer. Unless Seller requests an analysis of the Referee Sample before the Disposal Date, Buyer’s analysis shall be used to determine the quality of the coal delivered hereunder and shall be the Payment Analysis. The Monthly Weighted Averages of specifications referenced in §6.1 shall be based on the individual Shipment analyses. If any dispute arises with regard to the analysis of any sample before the Disposal Date for such sample, the Referee Sample retained by Buyer shall be submitted for analysis to an independent commercial testing laboratory (“Independent Lab”) mutually chosen by Buyer and Seller. For each coal quality specification in question, if the analysis of the Independent Lab differs by more than the applicable ASTM reproducibility standards, the Independent Lab results will govern, and the prior analysis shall be disregarded. All testing of the Referee Sample by the Independent Lab shall be at requestor’s expense unless the Independent Lab results differ from the original Payment Analysis for any specification by more than the applicable ASTM reproducibility standards as to that specification. In such case, the cost of the analysis made by the Independent Lab shall be borne by the party who provided the original Payment Analysis. XXXXXXXXX COAL COMPANY, INC. LG&E/KU Contract No. J12004

  • Escrow Analysis If applicable, with respect to each Mortgage Loan, the Seller has within the last twelve months (unless such Mortgage was originated within such twelve month period) analyzed the required Escrow Payments for each Mortgage and adjusted the amount of such payments so that, assuming all required payments are timely made, any deficiency will be eliminated on or before the first anniversary of such analysis, or any overage will be refunded to the Mortgagor, in accordance with RESPA and any other applicable law;

  • Quantitative Analysis Quantitative analysts develop and apply financial models designed to enable equity portfolio managers and fundamental analysts to screen potential and current investments, assess relative risk and enhance performance relative to benchmarks and peers. To the extent that such services are to be provided with respect to any Account which is a registered investment company, Categories 3, 4 and 5 above shall be treated as “investment advisory services” for purposes of Section 5(b) of the Agreement.”

  • Research Analyst Independence The Company acknowledges that the Underwriters’ research analysts and research departments are required to be independent from their respective investment banking divisions and are subject to certain regulations and internal policies, and that such Underwriters’ research analysts may hold views and make statements or investment recommendations and/or publish research reports with respect to the Company and/or the offering that differ from the views of their respective investment banking divisions. The Company hereby waives and releases, to the fullest extent permitted by law, any claims that the Company may have against the Underwriters with respect to any conflict of interest that may arise from the fact that the views expressed by their independent research analysts and research departments may be different from or inconsistent with the views or advice communicated to the Company by such Underwriters’ investment banking divisions. The Company acknowledges that each of the Underwriters is a full service securities firm and as such from time to time, subject to applicable securities laws, may effect transactions for its own account or the account of its customers and hold long or short positions in debt or equity securities of the companies that may be the subject of the transactions contemplated by this Agreement.

  • Reverse Engineering The Licensee shall not reverse engineer, decompile or disassemble the object code version of the Computer Program without the prior written approval of the Licensor.

  • Investment Analysis and Implementation In carrying out its obligations under Section 1 hereof, the Advisor shall:

  • Independent Analysis Each Party hereby confirms that its decision to execute this Agreement has been based upon its independent assessment of documents and information available to it, as it has deemed appropriate.

  • Engineering Network engineering handles the technical aspects of the project, resolution of problems escalated by the NOC, planning for future network expansion, and improving performance and process. Engineering interacts directly with AOL and the NOC.

  • No Reverse Engineering Licensee may utilize and study the design, performance and operation of Xbox solely for the purposes of developing the Software Title. Notwithstanding the foregoing, Licensee shall not, directly or indirectly, reverse engineer or aid or assist in the reverse engineering of all or any part of Xbox except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. Reverse engineering includes, without limitation, decompiling, disassembly, sniffing, peeling semiconductor components, or otherwise deriving source code. In addition to any other rights and remedies that Microsoft may have under the circumstances, Licensee shall be required in all cases to pay royalties to Microsoft in accordance with Section 6 below with respect to any games or other products that are developed, marketed or distributed by Licensee, and derived in whole or in part from the reverse engineering of Xbox or any Microsoft data, code or other material.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!