General Description & MV-Option Definition and Rationale Sample Clauses

General Description & MV-Option Definition and Rationale. Purpose of ECM is to increase the efficiency of the City’s HVAC systems. This is accomplished by:  Installation of selected DX HVAC units.  Application of coating to selected HVAC coils  Installation of programmable thermostats, as specified in Schedule A.
Sample 1
AutoNDA by SimpleDocs
General Description & MV-Option Definition and Rationale. 2. Purpose of the measure is to increase the efficiency of the city’s lighting systems. This is accomplished by replacing selected existing lighting fixtures with new energy efficient LED lighting systems. Boundary of Energy
Sample 1
General Description & MV-Option Definition and Rationale. The purpose of this ECM is to reduce the loss of energy through air infiltration or leakage around doors, windows, wall penetrations or poor or missing insulating materials that cause loss of conditioned air, or introduction of unconditioned air to conditioned spaces. The loss of conditioned air or introduction of unconditioned air increases the heating load on the heating systems and increases in cooling loads on Air Conditioning systems.
Sample 1
General Description & MV-Option Definition and Rationale. Purpose of the measure is to increase the efficiency of the city’s street lighting systems. This is accomplished by replacing selected existing lighting fixtures with new energy efficient LED lighting systems. Retrofitting existing lighting to the most current technologies available will provide significant reductions in both the electrical demand and consumption for the impacted fixtures. The Energy Cost Savings for this ECM is fundamentally a “rate change” in the billing from FP&L. Capacities and performance indices of the Lighting Retrofit ECM are presented below in this M&V plan.
Sample 1
General Description & MV-Option Definition and Rationale. The purpose of this ECM is to reduce water consumption and sewer service used in City buildings. Equipment such as water faucets, toilets, urinals and showers will be retrofit with reduced water flow equipment.
Sample 1

Related to General Description & MV-Option Definition and Rationale

  • 020 Definitions The following definitions shall be applicable to this chapter:

  • Classification Definitions Note: The following classification definitions should be read in conjunction with: • the stream and field definitions in subclause 1.4.3 and 1.4.75 respectively: • the definitions of “or equivalent”, “work within the scope of this level” and “Engineering Associate” at the end of this Schedule; • the National Metal and Engineering Competency Standards Implementation Guide especially Table 2 of that Guide which shows the alignment between old and new titles under the Australian Qualifications Framework. For example Advanced Certificates are now known as National Diplomas and Associate Diplomas as National Advanced Diplomas; • Clause 5.1.3 (f) Points. Trainer/Supervisor/Coordinator - Level 1 A Trainer/Supervisor/Coordinator - Level I is an employee who is responsible for the work of other employees and/or provision of structured on-the-job training. Such an employee has completed a qualification at AQFIII level or above, of which at least one third of the competencies are related to supervision/training, or equivalent. Notwithstanding the above definition an employee who is mainly engaged to perform work supervising or coordinating the work of other employees and who has sufficient additional training beyond that of those coordinated or supervised so as to enable the employee to perform work within the scope of this level shall be classified at this level. Trainer/Supervisor/Coordinator - Level II A Trainer/Supervisor/Coordinator - Level II is an employee who is responsible for the supervision and/or training of Trainers/Supervisors/Coordinators - Level I. Such an employee has completed an AQF IV or V qualification or equivalent of which at least 50% of the competencies are in supervision/training. WAGE GROUP: C14 Engineering/Production Employee - Level I As Engineering/Production Employee - Level I is an employee who is undertaking up to 38 hours induction training which may include information on the enterprise, conditions of employment, introduction to supervisors and fellow workers, training and career path opportunities, plant layout, work and documentation procedures, occupational health and safety, equal employment opportunity and quality control/assurance. An employee at this level performs routine duties essentially of a manual nature and to the level of his/her training:

  • Master Definitions Supplement All terms and expressions used in this Agreement shall have the same meaning as those contained in the Master Definitions Supplement to the CAISO Tariff.

  • GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.

  • General Definitions 1. For the purposes of this Agreement, unless the context otherwise requires:

  • 000 DEFINITIONS 6.100 Maintenance shall be work performed for the repair, renovation, revamp and upkeep of property, machinery and equipment within the limits of the plant property.

  • DEFINITIONS AND INTERPRETATION Definitions 1.1 In this Contract, unless the contrary intention appears: Activity End Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Activity Start Date means the date reported as such in a Student Statistical Report for an individual's enrolment in an individual subject. Apprentice has the meaning given to it in the Act. Approved Training Scheme means a training scheme approved under section 5.5.2 of the Act. Brokering Services means the recruitment of individuals to participate in Skills First subsidised training in exchange for payment from the Training Provider or the student. It excludes activities carried out by individuals who are employees of the Training Provider on the Training Provider’s payroll, whose role includes the identification and recruitment of potential students. Business Day means a day which is not a Saturday, Sunday or a public holiday in Melbourne, Victoria.

  • SECTION I - DEFINITIONS As used in this Agreement, the following terms shall have the meanings ascribed herein unless otherwise stated or reasonably required by the Agreement, and other forms of any defined words shall have a meaning parallel thereto.

  • Additional Definitions The following terms have the meanings given below:

  • 050 Definitions 3.48.060 Filing of FEPC and EEOC complaints not prohibited. 3.48.070 Informal and formal procedures. 3.48.080 Costs of hearing. 3.48.090 Representation. 3.48.100 Freedom from reprisal.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!