General Standard Operating Procedure. TEVA undertakes to comply with the requirements and operating procedures given in the Product Approval in the Territory.
General Standard Operating Procedure Sample Clauses
Related to General Standard Operating Procedure
Standard Operating Procedures Standard Operating Procedures shall not contravene the Canada Labour Code, the Canadian Human Rights Code, or the Collective Agreement, and an allegation of such contravention is subject to the grievance procedure.
General Standard Without prejudice to all other obligations of the parties under this contract, each party shall, in its dealings with the other for the purpose of, and in the course of performance of its obligations under, this contract, act with due efficiency and economy and in a timely manner with that degree of skill, diligence, prudence and foresight which should be exercised by a skilled and experienced: (a) network owner and operator (in the case of Network Rail); and (b) train operator (in the case of the Train Operator).
Technical Standards The Generation System shall be installed and operated by the Interconnection Customer consistent with the requirements of this Agreement; the Technical Requirements; the applicable requirements located in the National Electrical Code (NEC); the applicable standards published by the American National Standards Institute (ANSI) and the Institute of Electrical and Electronic Engineers (IEEE); and local building and other applicable ordinances in effect at the time of the installation of the Generation System.
General Standard of Care The Custodian shall exercise reasonable care and diligence in carrying out all of its duties and obligations under this Agreement, and shall be liable to the Funds for all loss, damage and expense incurred or suffered by the Funds, resulting from the failure of the Custodian to exercise such reasonable care and diligence or from any other breach by the Custodian of the terms of this Agreement.
General Standards An Assistant Professor will be competent to teach in a particular field, will be current in the literature of that field, and will seek to meet student needs in both the classroom and in non-classroom environments. However, an Assistant may be a junior member of the academic community, with little professional and/or teaching experience. Furthermore, an Assistant may have little experience in curriculum development, committee work, governance, professional and/or community service, etc. In short, an Assistant Professor generally will be new to tenure-track college teaching. For eligibility for promotion from Assistant to Associate Professor, the candidate must have served a minimum of four (4) years at the rank of Assistant Professor, and must show evidence that he/she has grown professionally and consistently has sought to meet student needs, in both the classroom and in non-classroom environments. A successful candidate for the rank of Associate Professor will have remained current in the field, and will have improved his/her teaching in some demonstrable way. He/she also will have demonstrated professional growth in one or more of the following ways: completion of additional appropriate course work (if applicable), attendance at professional conferences, service on campus and/or District committees, professional and/or community service, or, the production of some creative work. Evidence of professional growth will be drawn from a careful analysis of student evaluations and peer evaluations over a period of time, and from a critical reading of materials submitted by the candidate. For promotion from Associate to Professor, the candidate must have served a minimum of four (4) years at the rank of Associate Professor, and must show evidence that he/she has grown professionally to a point where he/she has mastered both a particular field of knowledge and the teaching of that knowledge. A successful candidate must show evidence that he/she consistently has sought to meet student needs, in both the classroom and non-classroom environments. A Professor should be a senior member of the faculty, one who has such substantial experience, knowledge, and skill that he/she could mentor junior faculty in his/her area of expertise. A Professor will have demonstrated all the same kinds of achievements and attributes necessary for promotion to the Associate Professor rank, but in addition will demonstrate that he/she is a leader in some appropriate sense. Evidence of professional growth and leadership will be drawn from a careful analysis of student evaluations and peer evaluations over a period of time, and from a critical reading of materials submitted by the candidate.
Service Level Standards In addition to all other requirements in this Agreement, and in accordance with the Best Claims Practices & Estimating Guidelines, Vendor shall use reasonable and good faith efforts to meet the Service Level Standards set forth below.
Design Criteria and Standards All Projects/Services shall be performed in accordance with instructions, criteria and standards set forth by the Director.
Specifications and Standards a) All articles supplied shall strictly conform to the specifications, trademark laid down in the bidding document and wherever articles have been required according to ISI/ ISO/ other applicable specifications/ certifications/ standards, those articles should conform strictly to those specifications/ certifications/ standards. The supply shall be of best quality and description. The decision of the competent authority/ purchase committee whether the articles supplied conforms to the specifications shall be final and binding on the supplier/ selected bidder.
General specifications For the purpose of this Regulation, the vehicle shall fulfil the following requirements:
GENERAL WORKING CONDITIONS Section 18-1. Employment begins and ends at each project site. Section 18-2. The selection of craft foremen and/or general foremen and the number of foremen required shall be entirely the responsibility of the Employer, it being understood that in the selection of such foremen and/or general foremen the Employer will give primary consideration to the qualified individuals available in the local area. After giving such consideration, the Employer may select such individuals from other areas. All foremen shall take orders from the designated Employer representatives. Craft foremen shall be designated working foremen at the request of the Employer. Section 18-3. There shall be no limit on production by employees nor restrictions on the full use of tools or equipment. Employees using tools shall perform any of the work of the trade and shall work under the direction of the craft foremen. There shall be no restrictions on efficient use of manpower other than as may be required by safety regulations. Section 18-4. Employees shall be at their place of work at the starting time and shall remain at their place of work performing their assigned functions under the supervision of the Employer until quitting time. The parties reaffirm their policy of a fair day’s work for a fair day’s wage. Section 18-5. All equipment assigned to a project shall be under the control of the Employer. The Employer shall have the right to determine how many pieces of equipment an individual employee shall operate. In an emergency, foremen shall operate any equipment assigned by the Employer, and there shall be no restriction on foremen in the use of the tools of his or her craft in such emergency. The foremen shall be from the craft normally operating the equipment. In accordance with currently recognized craft jurisdiction, the Employer shall determine the assignment of employees to start, stop, and maintain small portable construction equipment. Such work may be assigned to craft employees within a reasonable distance of their primary duties or an employee may be assigned full time to start, stop and maintain the Employer’s small, portable equipment on the job site. There shall be no over xxxxxxx of this type of equipment. The number of employees assigned to rigging and scaffolding operations shall be at the sole discretion of the Employer. The ratio of journeyperson to welders shall be determined solely by the Employer. Section 18-6. The Employer may utilize the most efficient methods or techniques of construction, tools or other labor saving devices to accomplish the work. Practices not a part of the terms and conditions of this Agreement, stand by crews and feather bedding practices will not be recognized. Section 18-7. It is recognized that specialized or unusual equipment may be installed and/ or serviced by individuals who have special training, skill, or qualifications and are not covered by this Agreement. Testing, inspection, or service performed on plant equipment under warranty may be performed by the vendor’s personnel. Section 18-8. Neither the Union nor its local unions shall coerce or in any way interfere with the Owner’s personnel, operation or facilities at the plant site. The Owner’s right to contract directly with other companies for work at the plant site shall not be limited, and the Union shall cooperate and not interfere with the Employer’s operations. Section 18-9. It is agreed that overtime is undesirable and not in the best interest of the industry or the employees; therefore, except in unusual circumstances, overtime will not be worked. Where unusual circumstances do exist, however, the Employer will have the right to assign specific employees and/or crews to perform such overtime work as is necessary to accomplish the job. Section 18-10. There will be no rest periods, organized coffee breaks or other non-working time established during working hours. Section 18-11. Individual seniority shall not be recognized or applied to employees working on projects under this Agreement. Section 18-12. The Employer shall establish such reasonable project rules as the Employer deems appropriate. These rules will be reviewed at the pre-job conference and posted at the project site by the Employer, and may be amended thereafter as necessary.
